cr touch pinout 3d models

Wanting to mount a BL-Touch V3.1 on my Creality CR-10 Mini i did not find a mount with the desired height and stability so i decided to design my own. It is much more stable because it also 'clamps' around the Extruder-mount back-plate. Furthermore...

I firmly attached it to the bracket that supports the bltouch for my cr-10 by shocksofmighty. I am releasing this design into public domain, allowing every individual to freely use it as they see fit. Conceived on Bobcad V30 Let us end human...

### Hardware Holes for the CR Touch are designed for M3 Screws & Nuts like my CR Touch Bracket ### Probe offset: -49.3, -16.7 Set with M851 X-49.3, and M851 Y-16.7 *I'm sure it's not perfect, but it's fairly close.* ### Print Settings See below...

https://www.printables.com/model/255772-cr-touch-left-side-mount-for-ender-3s1s1-proI redesigned it for my Ender 3 S1 Pro.Reasons for remixThe original had its X-offset being-55.5mm however this didn't allow me enough room for my X-axis to reach for...

The other issue I had (which may be the way I set up my printer) was that with the CR touch, my extruder was digging into the bed before the CR touch could sense the bed and retract. Hence I made the mount thicker to reduce the Z-offset. Finally,...

As the amazing project contains a bracket only for BL-Touch I've decide to "adapt" one for my CR Touch. This is a remix for https://www.thingiverse.com/thing:4943125 (Ender 3), but I believe it can also be used for Ender 5 as well Have used my...

This is for an Ender 3 v2 printer with CR Touch. I made the hot end connector three pieces to be able to move when performing auto bed leveling. The original design prevented the hot end from traveling the entire length of the x axis which is...

I recently bought a Bl Touch for my CR-10 V2 and was unable to find a mount that made use of the factory mounting point. This solution worked perfectly for me. ... The mount functions incredibly well with the tinymachines3D source code, which requires...

Ender CR Touch Mount The sensor can be adjusted a little bit in height (+ and - 3.5 mm from nominal). Designed the position (left front) such that it can't collapse with the Y-wheel on the left, and no limitation of the X-range. The sensor cable...

My OCD kicked in and I moved the screw holes to make it flush. The other issue I had (which may be the way I set up my printer) was that with the CR touch, my extruder was digging into the bed before the CR touch could sense the bed and retract. ...I'm...

(This is a second attempt at publishing this thing; I never managed to get the previous version listed) There are a few other CR-Touch probe mounts for the CR200B, but none of them worked for me. They either mounted behind the carriage (reducing...

(This is a second attempt at publishing this thing; I never managed to get the previous version listed) There are a few other CR-Touch probe mounts for the CR200B, but none of them worked for me. They either mounted behind the carriage (reducing...

This remix includes recess for M3 nuts and added material to move the CR Touch lower without using spacers. Attach sensor to mount using 2x M3 nuts and 2x M3x8mm or longer bolts. Attach mount to blokhead base / carriage using M3 x 8mm bolts. Step and...

I've had problems with bed leveling (wrong layer height acros entire bed - cr touch working properly, Z axis screws was moving, but it had wrong measurements because there is some problem in Y axis) like many others as i can saw through internet. Now...

I was working with this Satsana model that supports the metal brackets for the CR-Touch. I ran into two issues.The cable tie support on the top right of the model was super thin and broke mere seconds after removing it from the build plate.The...

*** NOTE *** You will HAVE to install mount and fan shroud to the plate BEFORE you attach the CR Touch to the mount!!!! Ensure the screw you use to attach the mount to the printer seats inside the recess of the print and is flush with surface. ...

Yes, and now this holder for a CR-Touch came out. The first variant was promising but a bit shaky. Because of this, I designed a second variant that can be clipped and fixed at the front of the hotend cover.</p> <p>I have uploaded both variants for...

Yes, and now this holder for a CR-Touch came out. The first variant was promising but a bit shaky. Because of this, I designed a second variant that can be clipped and fixed at the front of the hotend cover.<br /> I have uploaded both variants for...

YMMV.When putting together the x-carriage with the cr-touch, you have to put the cr-touch and bracket together first using 3mm screws (button socket cap) 6mm long iirc with m3 hexnuts. You then take that and slide it into place inside the first half...

remixed phosperus's carriage for cr 200b to mount orbiter.

Here I present my CR touch mount for my Ender 5.Unfortunately, none of the models online has pleased me and met my conditions,because with the standard mount you unfortunately break the sensor if you move the axes to the very left front. ...My first...

I need to bring down my bltouch to to match my new extruder CR-touch...

This Creality Sprite Extruder backplate relocates the CR Touch probe to X=-47mm, Y=0mm. This allows the bed mesh to be more accurate along the Y axis because the hotend lines up exactly with the probe (useful if the Y extrusion is warped). ...It also...

My probe kept hitting those bed clips because the new BL Touch 3.x model is slightly taller than its predecessors, so I adjusted it by remodelling the mount using Blender3D.

... Good luck to install at finished Touch UI with your sreen but I don't know why, Touch UI (0.16.0) works only with Octoprint 1.3.8, not newer. ... I think this is usable with 3D printers cases who have the same design as Geeetech for exemple.

When installing Touch UI on your finished setup, good luck is recommended, as I've encountered an issue where Touch UI (0.16.0) only works seamlessly with Octoprint 1.3.8 and not with newer versions. ... This case design is compatible with 3D printer...

... Creality Spider hotend requires the probe to be lowered in order for it to work. ...I made this quick design to compensate for the spider hotend size difference. This should also work for other Ender printers that use the stock hotend and the BL touch

(the spacer is the same one you use to adjust the fans).When installing use washers', Screws through CRt and bracket then washer then nutThe X/Y Offset I use:X= -1.8&nbsp;Y= -37.5&nbsp;Print Setting:Layer height 2.0 or 1.6 (I prefer 1.6)Infill 100%...

This is for non H users looking to upgrade to BL touch. NOTE: +0.20 Tolerance added to holes. 1: i have not printed this 2: Original part is aluminium. I suggest printing in HT materials or using this as a template to make one from aluminum. 3: I...

I wanted to mount my RPI below the touch screen of the printer, so I made this mount. I had to do some filing with the first version of the below_screen_base.STL to get the screws in straid. For version 2 I made the hols .5mm wider and moved the...