cr touch pinout 3d models

Original : https://www.thingiverse.com/thing:3179892 I want use this duct system and CR touch same time. So.. I modified it. ... need extra m3 nut and some zip tie.

Here is a dual 5015 fan Satsana remix with a CR Touch mount included, based on https://www.thingiverse.com/thing:4697079. Check it for more details on printing and fans. ...

Edited fan body version to use with CR touch mounting bracket because extra clearance is needed. Not tested yet. ... Use original printing settings as noted in original Fang Fan Duct for Ender 3 v2 by MakerSmitty

Remix of X-Limit switch housing to mount a MS Lifecam Studio / Cinema for Ender 3 v2 when you have CR-Touch ABL (Unsure of BL-Touch) I didn't think before printing the original and the xcarriage crashed into it as it was trying to home as the ABL...

I bought my printer and when I saw the design by Jargs for covering the QR Code I was amazed, but I wanted to upgrade my printer to add a CR Touch. Once installed, I realized that the button for the X axis couldn't be pressed. I modified the model...

I bought my printer and when I saw the design by Jargs for covering the QR Code I was amazed, but I wanted to upgrade my printer to add a CR Touch. Once installed, I realized that the button for the X axis couldn't be pressed. I modified the...

This design works really well in terms of allowing one to monitor prints remotely, but one issue I had involved the CR Touch colliding with the camera mount when homing. I edited this part to give the CR Touch clearance when homing. After opening...

This design will work with both the Creality BL Touch and CR Touch mounts since the mounting brackets are very similar. [thanks Locksen for verifying this] All the hardware you need should be found when disassembling the original fan shroud, so...

I am using it with 2 washers as I realized, that the CR touch is also a bit shorter compared to the BL Touch. The gantry mount can be printed both laying flat without supports and vertically with supports. ...The second option is recommended due to...

... a nice gray and pink paint job.--UPDATE: I added a CR-Touch compatible version. There's very little room between the x-motor and the CR-Touch, so if you find that my model doesn't work for you, you might also check out this remix by bkbilly instead.

This adds a similar to stock fanguard, with a little extra reinforcement also to keep the arm for the CR Touch from bending. As with the original:x_offset: -46.8y_offset: 0You will need two M3 nuts to attach the CR touch. ...Still no supports...

Vous pouvez également récupérer la partie permettant la fixation du Touch-MI sur un fang spécifique via BreezeBlock _ FanShroud _CR-10_Stock_MicroSwiss_5015 : https://www.thingiverse.com/thing:2814717. ... L'adaptation Breezeblock_Harness pour Touch-MI...

You can also retrieve the part allowing the fixing of Touch-MI on a specific Fan: BreezeBlock _ FanShroud _CR-10_Stock_MicroSwiss_5015 : https://www.thingiverse.com/thing:2814717 Adaptation Breezeblock_Harness for Touch-MI :...

Just added a hole to the creator's design (https://www.printables.com/model/255772-cr-touch-left-side-mount-for-ender-3s1s1-pro) to be able to access the tensioner screw, not really need to touch it until you start to have extrusion problems like I...

... ... In packet is spool filament holder, mount for filament sensor and mount for CR touch sensor. Also you can rotate spool holder if you screw it only with one screw. Evreything works and fits fine. ...You will just need some M3 screws and nuts.

... without sensor protection. ...I made this because the original design is not compatible with cr-touch. I've also added the sldprt file if you want to edit it. ... Little ridges in the design (photo 2) are unnoticeable and make it fit tightly.

Made a remix with the following desingns https://www.thingiverse.com/thing:4960249 https://www.thingiverse.com/thing:5141820 https://www.thingiverse.com/thing:4736330 Made this so i can easy change the nozzle and still have the CR touch and laser...

This is a mini satsana remix that works with the original cr touch mounts and the creality direct drive kit. It's a good idea to take to screws from the hotend fan and use them to mount it into place as you can see in the picture above. ... Check out...

Remixed the modular arm bracket from https://www.thingiverse.com/thing:4213384 with the modifications to the predecessor non-modular bracket remix that prevents collisions with the CR-Touch sensor (https://www.thingiverse.com/thing:3481096) so the...

Mounts a 5015 fan for the heat break and moves the cr touch inline with the nozzle on the left side. ...Clears the gantry.Set heat break fan to 50% fan speed for ultra quiet operation.X-Offset is -50.7

Added a cutout for the CR Touch wire connector and switched the lateral support to the other side of the probe mount. Added the creality dragon to the front. (Dr Boo's Creality Dragon Logo - printable (https://www.thingiverse.com/thing:2873554)...

... on my Cr-10s printer. ...To enable bed leveling, I modified some features of this design https://www.thingiverse.com/thing:3197146, allowing me to mount the BL-Touch sensor directly onto the hotend cooling block for optimal cooling performance.

Made a remix with the following desingns https://www.thingiverse.com/thing:4960249 https://www.thingiverse.com/thing:5141820 https://www.thingiverse.com/thing:4736330 Made this so i can easy change the nozzle and still have the CR touch and laser...

... of the mount with the stock screws. Zip-tie wiring to the strain relief bracket. Design is based of a model of the stock CR-10 hotend by Geoff Tayler on GrabCAD https://grabcad.com/library/cr10-stock-hot-end-1 Full step model included for remixes

I thickened the mount's arm for added strength and to slightly lower the probe height, added a piece that sits against the left edge of the Micro-Swiss frame to help with alignment, enlarged the semi-circular cutout to better clear a screw head on...

There's very little room between the x-motor and the CR-Touch, so if you find that my model doesn't work for you, you might also check out [this remix](https://www.thingiverse.com/thing:5276100) by [bkbillybk](https://www.thingiverse.com/bkbillybk)...

The **CR Touch** support is placed as close as possible to the nozzle so in the ***Configuration.h*** for the ***Marlin*** firmware the values for the *NOZZLE_TO_PROBE_OFFSET* should be: ``` #define NOZZLE_TO_PROBE_OFFSET { -37, -7, 0 } ``` A new...

Minimus system: https://cults3d.com/en/3d-model/tool/minimus-hotend-cooler-system This is a custom backplate for the Minimus with double 4010 part coolers and a 4020 material cooler + cr touch. I have a microswiss hotend, does not work with stock...

The goal of this remix is to be able to use the Satsana Ender 3 Fan Duct with a CR Touch and the Creality Spider 3.0 all-metal hot end. Notes: It currently sits as a WIP due to the original part being marked WIP. ... Pictures of both FDM and Resin...

... have been able to finally create my own model of satsana. This sastana has 3 front mount screws. CR / BL Touch adapter. Direct drive adaptation. And stock parts / Fans only. An amazing piece. ...i hope others are in need of this as i was.