cr touch ender 6 3d models

Update 1; I found that when I printed the original model I indented the wrong side of the mount for the CR touch and that the indentation was also too big, I have edited this and made the indentation smaller and on the correct side, I have printed...

I couldn't find a proper mount for the CR Touch when I printed out the Blokhead, so I just put in a little cut out for all of the wires to slide through.

... a nice gray and pink paint job.--UPDATE: I added a CR-Touch compatible version. There's very little room between the x-motor and the CR-Touch, so if you find that my model doesn't work for you, you might also check out this remix by bkbilly instead.

This was measured and recreated off of the stock Ender 3/ / Ender 3 Pro CR Touch mount. I'm uploading this so people can use it as a reference point for making custom holders / integrating it into extruder mods. Drop a like if this helped you! ...

I remixed this awesome mount for the BL touch to accommodate a CR touch, and still front mount it to the H2. You will need the following to install this mount:4 x M3x8mm screws2x M3 NutsMy Probe offsets are:X = 28.25Y= 27.60Z = 0.57

I need something that would push the filament a bit further out from the Z-axis as I have mounted a BMG Dual gear extruder sideways of where the original extruder is on the CR-6 SE and have a top mounted spool holder. This extended arm aligns thing...

The goal of this remix is to be able to use the Satsana Ender 3 Fan Duct with a CR Touch and the Creality Spider 3.0 all-metal hot end. Notes: It currently sits as a WIP due to the original part being marked WIP. ... Pictures of both FDM and Resin...

Hence the merging of two existing designs.My Ender 3 has direct drive & CR Touch with printed (4020) fan cowl I liked Dannys' mounting design which I trimmed and added Benjis' drag knife holder and spring clamp.Still uses original mounting holes but...

Soporte para sensor de autonivelado de cama CREALITY CR TOUCH para hotend V6 tipo  Trianglelab DDE.Necesarios 4 tornillos M3x10mm.Carro extrusor Trianglelab DDE V6...

A shim or spacer when extra z-offset is required to install the CR Touch. Recommend 90% infill 1mm and 2mm versions are available for download. Follow the link to Tinkercad to customize size. This object was made in Tinkercad. ...Edit it...

Fan fairing for replacing the extruder fan with 40 x 40 x 20 mm. ...It is compatible with standard CR-Touch support. The passage of the cables of CR-Touch is integrated

Adapted dmatos's BL Touch mount for Creality's new CR Touch probe for my Ender-3 Pro. I thickened the mount's arm for added strength and to slightly lower the probe height, added a piece that sits against the left edge of the Micro-Swiss frame to...

I originally came across this model from Printibles user 3dprint, then I found the original model on Thingiverse that had the .step files and I ended up editing the model in Fusion360 to fit the Ender 2 Pro and a Cr-touch/Bltouch. FeaturesActive part...

... desk-space. ...So I adapted the Ender 3 metal spoolholder. When putting the filament on top you have to also have some kind of guide to feed at an relaxed angle. The guide is made out of two parts that connect with 4 small self driving screws. ...

This prevents the part cooling from aiming too high, at your nozzle.** If you have a CR-Touch, the Satsana remixes that have the integrated BLTouch mount will NOT work! The position of the wiring connector is right between the 2 mounting screws. This...

It's recommended you do this first with just the screws (no CR-Touch or cable support) to make the threads, then take out the screws, and then attach everything to the backing plate. Remember to change your X, Y, and Z probe offsets. ...You'll need to...

Remixed tsuga's model to work on E3v2. ...Clearance for X endstop.Original model: https://www.printables.com/model/333070-cr-touch-zero-offset-probe-backplate-mount

Do modulu byli přidané snímače ( CR-Touch ,Pinda probe V1) a pod ventilátor jsem nalepil Led pásek 12V ktery je ovladaný od ventilátorů + odpor 620 ohm

Just notched out the bracket a bit for the CR Touch cable to clearance. ...Original model works fine, but puts too much stress on the small wires.

I bought my printer and when I saw the design by Jargs for covering the QR Code I was amazed, but I wanted to upgrade my printer to add a CR Touch. Once installed, I realized that the button for the X axis couldn't be pressed. I modified the model...

Mounts a 5015 fan for the heatbreak and moves the cr touch inline with the nozzle on the right side. Clears the gantry. Set heatbreak fan to 50% fan speed for ultra quiet operation. You will need to extend the CR Touch wires. ... x offset=37.687

Mounts a 5015 fan for the heatbreak and moves the cr touch inline with the nozzle on the right side. Clears the gantry. Set heatbreak fan to 50% fan speed for ultra quiet operation. You will need to extend the CR Touch wires. ... x offset=37.687

All credits (and hail) to the wonderful Rogue Paul for giving us the free ----> Minimus Hotend Cooler System <---- You can grab the whole suite here: https://cults3d.com/en/3d-model/tool/minimus-hotend-cooler-system This is a remix of his Ender 3...

Using E30Andrew's Satsana Ender 3 Fan Duct for CR-Touch. ...In order to use this in conjunction with Benawhite's Ender 3 - Direct Drive Adapter, the cable channel needed to be moved or shaved off. In my case it broke off cleanly during install, so I...

I have a CR Touch and I wanted it on the right side anyway so I went to work. This is my 1st design so please be kind. After 9 reprints I finally came up with something that worked. Enjoy. I wanted a place to mount a digital gauge for axis...

I have a CR Touch and I wanted it on the right side anyway so I went to work. This is my 1st design so please be kind. After 9 reprints I finally came up with something that worked. Enjoy. I wanted a place to mount a digital gauge for axis...

Original : https://www.thingiverse.com/thing:3179892 I want use this duct system and CR touch same time. So.. I modified it. ... need extra m3 nut and some zip tie.

This is a custom backplate that moves the CR Touch in line with the nozzle so that the Y-offset is 0. ...It also includes a mounting point for an accelerometer.

I've modified the original model with a 2.5 mm lower bracket, this becouse, for some reason my cr touch was to high on the mount resulting in the noozle crashing into the bed while using the mesh leveling.

Here is a dual 5015 fan Satsana remix with a CR Touch mount included, based on https://www.thingiverse.com/thing:4697079. Check it for more details on printing and fans. ...