cr touch ender 6 3d models

Same mount as original just added a cutout for the cr touch plug

Make a CR-Touch mountable after breaking the fragile mounting tabs. ...

Cr Touch Cover work in progress for just a better and easy design

With this remix, I have also included the STLs for the Pi Camera body and mounting arm from Michael (Modmike) Triffon's Creality Ender 3 Pi Cam Mount which fit the CR-6 SE as well. You should be able to follow the assembly pictures to see how to...

Edited fan body version to use with CR touch mounting bracket because extra clearance is needed. Not tested yet. ... Use original printing settings as noted in original Fang Fan Duct for Ender 3 v2 by MakerSmitty

I built this for my Ender 3 since I fell in love with the CR-10 SE's sleek design. ...All you have to do is secure one screw at the top, and you're ready to go.

I like how the bed is held in place on the CR-6 SE so I wanted that on my ender 3 as well.The clips are attached to the bed, so you cannot loose them and only cover the build plate the bare minimum. You will need per clip a M3x20 bolt, an M3 nut and...

I like how the bed is held in place on the CR-6 SE so I wanted that on my ender 3 as well. The clips are attached to the bed, so you cannot loose them and only cover the build plate the bare minimum. You will need per clip a M3x20 bolt, an M3 nut...

CR Touch version of https://www.thingiverse.com/thing:5318363

... I'm sure it would work with a BL Touch too, but it's specifically designed for the CR Touch. The CR Touch is a little bulkier than the BL Touch, so there's not a lot of material on the small clip end. I'd recommend going with 40% infill minimum.

I designed the cover for the CR-Touch because it goes into error mode if you get too close to it with a PI-IR cam. it seems that the Pi-cam's IR lights are crashing the CR-Touch. the cover prevents it from going far. At a distance of 1 cm between...

... mount added to design. I do not know the X, Y, or Z offsets figured out yet so let me know if get it dialed in. In theory, they should be: X=+30.6 Y=-12.5 I don't have the CR touch installed so let me know if you find the offsets to be different.

Estuve buscando varias opciones para mejorar la ventilación de capa de mi Ender 3, actualmente tiene un ventilador radial 5015 y una sonda de nivelación, para esta ultima me tome la libertad de modificar el soporte del bltouch del diseño original del...

Remix of X-Limit switch housing to mount a MS Lifecam Studio / Cinema for Ender 3 v2 when you have CR-Touch ABL (Unsure of BL-Touch) I didn't think before printing the original and the xcarriage crashed into it as it was trying to home as the ABL...

This is a remix of Skia_MKX's remix of Satsanas design for the fan ducting for the micro swiss direct drive conversion for the ender 3's and the CR-10s to allow use of the CR-Touch. https://www.thingiverse.com/thing:4933205 The reason I remixed this...

Se reajusto el soporte del Bltouch para poder meter un CR-touch ya que el cable esta ubicado en distinta forma

Standard mini satsana with side cr-touch. in case it would be usefull for someone else. ... Z-offset should be around -1.1 for my microswiss

Here is a Ender 6 version (with the recesses) of the "new" or "updated" minimus fan shroud backplate. ...4/15/2023

Remixed the BL Touch attachment for the CR Touch. Fits perfect and works great. ... Moved the mounting holes over to be lined up with the vertical adjustment holes so the wires go up the channel properly as well.

I like the Micro Swiss dual fan kit, but the author didn't have the CR Touch mount, only BL Touch which is different. So I drew my own. ...

... the mounting holes on. ...Couldn't find anything else on the internet, so here's what I came up with in tinkercad. Printed in Resin, since my FDM printer was dead in the water until I could get the CR-Touch working again. ... Your mileage may vary!

... ...Two m3x8 screws and two m3 nuts are required to mount the CR Touch. The thicker one work for me. It depends on the position of the holder and the hotend. I have stock hotend. ...You also need two m3x8 screws and two m3 nuts for a thicker holder.

I am using it with 2 washers as I realized, that the CR touch is also a bit shorter compared to the BL Touch. The gantry mount can be printed both laying flat without supports and vertically with supports. ...The second option is recommended due to...

Designed for the Ender 3 V2 and supports the original steel BL/CR Touch mounting bracket. This design will work with both the Creality BL Touch and CR Touch mounts since the mounting brackets are very similar. [thanks Locksen for verifying this] ...

UPDATE*** 1/2/20 Confirmed fit on Creality CR-6 se. ____________________________________________ EDIT*** 6/13/20 Added notched version for use with TH3D EZABL bed leveling sensor. Without it, the Z axis will not trigger because the EZABLE support...

Designed to be printed with TPU.There are 2 versions, one is 32mm tall the other is 46mm tall.You will need to print 4 of either.Print SettingsPrinter:Creality CR-6 seRafts: NoSupports:NoInfill: 10Filament:Priline TPU Black Notes: Category: 3D...

... without sensor protection. ...I made this because the original design is not compatible with cr-touch. I've also added the sldprt file if you want to edit it. ... Little ridges in the design (photo 2) are unnoticeable and make it fit tightly.

UPDATE*** 1/2/20Confirmed fit on Creality CR-6 se.EDIT*** 6/13/20Added notched version for use with TH3D EZABL bed leveling sensor.Without it, the Z axis will not trigger because the EZABLE support bracket hits the cover.EDIT*** 2/2/20Added a few...

Designed for the CR-6 SE/MAX, but the Ender 3 line of printers uses the same endstop cap, so it should work there too. ... ######################################################################## As always, I'm not asking for your money, but it...

Using E30Andrew's [Satsana Ender 3 Fan Duct for CR-Touch](https://www.thingiverse.com/thing:4970480/files). In order to use this in conjunction with Benawhite's [Ender 3 - Direct Drive Adapter](https://www.thingiverse.com/thing:3386628), the cable...