cr touch ender 6 3d models

are you struggeling with calibrating the CR touch or any other sort of probe, chanses are that your x axis may be twisted. this makes the distance between nossle and the probe to bed different. x offset doesnt really matter, but if this is the case...

I had remixed this Satsana Fan shroud from several others model and after creating it I had discovered the stock Cr touch placement would interfere with the part cooling fan. So I had made a different mount so to basically flip it around so the side...

... did not perform very well. So I remixed an existing (hopefully proven) file to fit to this DD Kit. It has an attachment point for a CR Touch. I am not sure if a BL Touch will fit, becuase it has a shorter throw I think. ... Maybe it helps someone

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

I've increased the dimensions of the top bracket and added some more brackets to the bottom (v2).On the ABL mount I've cut out a slot on the top to make the wires fit for a CR Touch. I've also made a slot along the bottom for it's cables to route...

This is a BIQU H2 mount on the latest Ender 3 v2 mount.

Redesigned bracket to clear CR TouchDesigned an extension bracket to get a better view of the nozzleRedesigned camera housing for an Arducam Pi Camera with Motorized Lens (https://a.co/d/eDK9wCd)

Hobbled together something that will work to properly allow the NG extruder to hit the X-Axis limit switch on the Ender 3 V2 Neo from Creality. ...The switch style is that of the Ender 3 S-1 model which lays flat instead of vertical.

I made this to attach a 1" travel dial indicator to my Ender 3 V2. It requires a CRTouch bracket (though not necessarily the sensor itself). It mounts above the bracket using the brackets mounting bolts. The indicator I am using is this one...

Remixed https://www.thingiverse.com/thing:4647793 Added a draft angle to the face that mounts to the stock Ender 3 v2 carriage plate as my Hemera, and therefore nozzle, were not square to the axis/bed. The draft angle "pushes" the bottom of the...

thanks and hope this helps anyone lol print it with many wall layers and then 100% infill would probs be strongest Adding offsets cuz I'm using it rn and it works for me: Ender 3 pro: X= -47, y= -5, z =-0.36 but irrelevant cuz you can just change...

I also wanted it to sit in line with the Y-Axis of the printer nozzle.Offsets for the prove are X: 39 and Y: -1 (Z offset should be the same as the stock mount location)I'll link my Noctua 40x40 fan mounts as I finish them as well.UPDATE:...

I liked the design of the combined USB (micro)-SD card holder but I wanted to attach it firmly to my printer. ...So I added a hook to hook the holder to the aluminum profile of my CR-6 SE. ...

I made the following changes: - made the screw holes smaller to fit the m3 screws included with the CR Touch - made a cutout so that the cable connector on the CR Touch is accessible - removed the top cable brackets so it can be printed without...

Had one for the stock setup and worked great, but this fan mount interfered with it since it used the same mounting holes.Mixed in my CR-Touch mount with Lautrec_996's 45 degree fan mount.Let me know if you'd like me to mix in the mount to one of the...

I made it compatible with the CR Touch.Their design did not let my CR Touch sensor sit perpendicular to bed; The sprite's screws were in the way. Also, the runout sensor seemed a bit too low and would make contact with part of the sprite.I added the...

The additionnal length of this mount puts the probe at a position where it will not hit a Pi cam mount placed on the QR Code covering the X axis motor.This was only tested with a CR Touch. ...I'm assuming the BL Touch has the same dimensions has not to...

The additionnal length of this mount puts the probe at a position where it will not hit a Pi cam mount placed on the QR Code covering the X axis motor.This was only tested with a CR Touch. ...I'm assuming the BL Touch has the same dimensions has not to...

The Creality Spider hot end lowers the nozzle requiring the probe to be lowered accordingly. ... This design is made for the Ender 6 with a Creality Spider. Tested with BL Touch, added cable notch for CR Touch.

Remixed from Mesmer88 - a commenter said to make it thicker so I did.You may be able to get away with stock M3 screws by putting the bracket over top of the fan mounting shroud. Better is to get slightly longer M3 screws and place the bracket under...

Satsana fan duct with cr-touch bracket cutout for 4010 or 4020 fans, compatible with Ender 3 and Ender 3 v2.

... Ender 3/Ender 3 v2 printer with a MicroSwiss direct drive installed. ...This allows for usage of the Cr-Touch without a printed part, you'll need to use the ender 3 cr touch mount bracket and screw through the fan duct.Printed with PETG at .20mm 

... the Ender 3/Ender 3 v2 printer with a MicroSwiss direct drive installed. ...This allows for usage of the Cr-Touch without a printed part, you'll need to use the ender 3 cr touch mount bracket and screw through the fan duct.Printed with PETG at .20mm

Ender 6 direct drive mont with Bl-Touch holder. ...

Remixed two designs together; unlike all other designs, first one didn't interfere with CR touch, 2nd had Ender logo I liked.

This is a custom direct drive setup designed for the Ender 3, CR10, CR10S, CR10S4, and CR10S5 printers, utilizing a BMG extruder and an E3D V6 hotend. The primary intention was to couple the BMG extruder directly to the E3D V6 hotend without any PTFE...

hi, i was looking for some cr touch bracket, but i've cannot find anything good for my ender 3 pro with satsana fan duct already printed. here you can try this on yours ender 3/3pro. be carefull! at first you have to carefully set the X axis...

Support for CR-Touch developed for CR-200B hotend.

A CR Touch Adapter for SATSANA FanHead for Ender 3 & v2. ... Enjoy