cr touch ender 2 pro 3d models

Add a touch screen interface for Klipper on your Ender 3 / Ender 3 Pro / Ender 3 V2 with a 4inch LCD touch screen + KlipperScreen. More information: https://youtu.be/jIFCERxnAXU https://www.youmaketech.com/ender3-touch-screen-interface-for-klipper/...

Ender-3 Pro 3D touch sensor mount This is a remix from https://www.thingiverse.com/thing:3383611 Just added 3.5 mm to bring the sensor a bit closer to the bed.

 I upped the perimeters to 4 and upped a gyroid infill to 50% for more stiffness.BL Touch offset (z offset is approximate) * +-- BACK ---+ * | [+] | * L | 1 | R <-- Example "1" (right+, back+) * E | 2 | I <-- Example "2" ( left-, back+) *...

Ender 2 Pro storage cover after upgrade

Ender-5 Pro BLTouch / 3D touch sensor mount This is a remix from https://www.thingiverse.com/thing:3383611 Just added 2.5mm to bring the sensor a bit closer to the bed. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No...

Ender-3 Pro 3D touch sensor mount This is a remix from https://www.thingiverse.com/thing:3383611 Just added 3.5 mm to bring the sensor a bit closer to the bed. ...Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA...

Mount the China BL touch on the Ender 3 Pro's endstop bracket securely with screws provided. Then, print a small glue holder at a thickness of 1.5 mm using iron plate material. ...Mark the holes for mounting the glue holder and carefully drill them into...

A more rigid version of the BL-Touch mount for the Ender 3 Pro Fang Duct. Printed with Tree Supports and high infill. Edit: After printing I noticed that the part is slighty to large. The side of the upper support tentacle touches the...

BLtouch mount for Ender 3 Pro Microswiss Direct Drive kit, offsets the BLT 60 degrees, enabling you to take the standard Ender shroud off without removing BLT.

Just bought the Ender 2 Pro and Creality CR-Touch. No Mount that i can use with this printer in the Box. So, the solution: I found one here, plus my thought with the inserts in the two holes forwards (M3/6) and with Tinkercad I made something that I...

I made an enclosure for my Ender 3 S1 Pro and wanted to put the controller outside for easy manual control... (I might build an Octoprint RPi enclosure with switching relays etc at some point as one larger unit integrating the touch control...). ...

This is a remix for brunofporto's bracket BFP Touch with reference on auroratechchannel's 3D touch bracket for ender 5, so this is bfp touch bracket not the 3d touch, special thanks to both of them!

It is processed to fit perfectly on stock Ender 3 Pro. Due to the fragile nature of the initially design of the BL Touch mount, it was remixed into more strong one.. Both turbine fans are wired into one socket to the board.. Optional printing...

... The BL touch requires a Z offset of 0.48mm from the nozzle on mine, serving as a useful starting point for fine-tuning the calibration. For maximum durability, I recommend printing this mount in a robust material such as Carbon Fiber PLA/ABS/PC.

(At least on the Ender 3 V2 with the Sprite Pro extruder) You would then set the endstop position to keep the nozzle zero above the build plate. The fit is good, you will need slightly longer M3 screws than the ones originally used to mount the...

Ender 3d direct drive with Bl-Touch holder. It's really easy to print, but a little bit tricky to remove the supports. Original screws used, you can use the original extruder if you want. Motor cable must be extended. I did by soldering some...

- Place the assembly on the Ender 3/Pro and start both screws but don't tighten yet. - Press down firmly on the area below the LCD but just above the mounting screws so that the cut away on the back is held against the aluminum extrusion. - Then...

Support for CR-Touch developed for CR-200B hotend.

Держатель катушки для Ender 2 Pro. ...Крепится комплектными винтами. Filaments spool holder for Ender 2 Pro. ...Attach with the screw included in the kit.

Держатель катушки для Ender 2 Pro. ...Крепится комплектными винтами. ------------------------------- Filaments spool holder for Ender 2 Pro. ...Attach with the screw included in the kit.

Finally, I added a mount for a BL/CR touch. I have had some issues with it running into the X-axis stepper motor mount, but I solved that by removing the mount entirely and printing an adjustable X-axis endstop mount. You may need to add a couple...

Ender 2 PRO motherboard cover for 4040 fan and 5050 fan

This a remix of the Mini Satsana for the Ender 2 Pro. ...

Remastered from a familiar concept, I simplified its design to make it compatible with numerous Creality Printers such as Ender 3 and CR-10 models.

This is a remix changing the magnet orientation in order that the magnet is facing the Touch Mi.

... offset used, should fit with a 12mm bolt, with 1 M3 hexnut to lower the sensor to +0 offset.   Roughly the height of the ABL Mount.https://www.printables.com/model/197773-ender-2-pro-abl Thanks to Hair for the original offset cover Printed in PLA.

This design brings the BL touch very close to the nozzle and accommodates two 40mm fans for good cooling. I run the hot end cooler blowing outward "away" from the printed parts. The design is meant to have 3mm brass melt-in inserts where...

I wasn't happy with the touch screen being the widest point of my printer, so I designed this to move it inboard and save some room. It prints in two pieces and snaps together, no supports required. It's a pretty good friction fit so no glue...

DIY Creality Ender 3 / Ender 3 Pro / Ender 5 / Cr-10 Extruder Knob.

... y 14.5 Questions and suggestions are welcome. CR10, CR10S, CR10S4 and CR10S5 mounts can be found here: https://www.thingiverse.com/thing:3721746 06-29-2019: A BL Touch mounting plate has been added to this design. ...It still requires testing.