cr touch ender 2 pro 3d models

Ender 2 Pro Led Halterung, Benötigt werden ein parr M3 Schrauben und Natürlich die LED´s Stecker und Kabel. ich verwende Neopixl die über das SKR Mini e3 V3 gesteuert werden bei den verlinkten LED´s passen 2x6 in die aufnahme, kleben ist nicht...

The Creality Ender 3, Ender 3 Pro, and CR-10 Extruder Knob are highly regarded components for 3D printing enthusiasts. These extruders offer impressive performance and reliability. With a focus on precision and ease of use, they cater to both...

I created a simple screencover for the Ender 2 Pro to make it dark at night. It´s a tight fit so it wont vibrate during printing.It prints without supports flat on the build plate.The "Winged Rotary Knob" by HiddenP56 works perfetly together with...

**Description** ==================== This is a remix of TinyTouch NMPG, a very cost-efficent alternative to BLTouch and other commercial products - adapted for use on Ender 3/Ender 3 Pro with stock extruder assembly Please note that even though this...

I made the following changes: - made the screw holes smaller to fit the m3 screws included with the CR Touch - made a cutout so that the cable connector on the CR Touch is accessible - removed the top cable brackets so it can be printed without...

... a 26mm piece of 4m rod that was pushed into place once heated. ...You want 16mm of the thread on show. Print Settings Printer: Ender 2 Pro Rafts: NoSupports: No Resolution: 0.2Infill: 20-25% Filament: Amazon PETG Orange Category: 3D Printer Parts

# Ender2Pro-BlTouch BLTouch bracket for the Ender2 Pro ## Installation This should work with the M2.5 nuts/screws provided with the BLTouch _or_ you can use M3 screws (with no nuts). Note: When using M3 screws, you will be tapping directly into...

Ender 2 pro LED holder for bltouch holder https://www.printables.com/en/model/197622-ender-2-pro-hot-end-fan-mount-with-cr-touch-bl-tou

... FDM printers are known for their reliability and affordability, making them a popular choice among hobbyists and professionals alike. ...The Ender 3, Ender 3 Pro, and CR-10 series are all well-regarded for their ease of use and high-quality prints.

I made it compatible with the CR Touch.Their design did not let my CR Touch sensor sit perpendicular to bed; The sprite's screws were in the way. Also, the runout sensor seemed a bit too low and would make contact with part of the sprite.I added the...

The additionnal length of this mount puts the probe at a position where it will not hit a Pi cam mount placed on the QR Code covering the X axis motor.This was only tested with a CR Touch. ...I'm assuming the BL Touch has the same dimensions has not to...

The additionnal length of this mount puts the probe at a position where it will not hit a Pi cam mount placed on the QR Code covering the X axis motor.This was only tested with a CR Touch. ...I'm assuming the BL Touch has the same dimensions has not to...

Creality Ender 3 and Ender 3 Pro users often report issues with their extruder knob not turning smoothly, which can make it difficult to adjust the temperature or tension. This problem typically arises from wear and tear on the gear teeth, causing...

It was hard to find a 40x40 24v fan near me so I design this support for 5015 fan. ... I really like Rocco 81-92 job on his parts and this is my little contribution.

A coupler made from a combination of an extruder and Teflon tube on the Creality CR2 (Ender 2) consists of plastic (female thread) and metal (male thread), respectively. Frequent installation or reinstallation can cause significant damage to the...

This piece works with all Creality Ender 2 / 3 / 3 pro / CR-10 printers and should also work on all printers with a Z-axis of 8mm diameter. You will need an M4 screw and a ball bearing (type Abec 7) to fix it. This two-piece part replaces the...

Remixed from Mesmer88 - a commenter said to make it thicker so I did.You may be able to get away with stock M3 screws by putting the bracket over top of the fan mounting shroud. Better is to get slightly longer M3 screws and place the bracket under...

Ender-5 Pro BLTouch / 3D touch sensor mount This is a remix from https://www.thingiverse.com/thing:3383611 Just added 2.5mm to bring the sensor a bit closer to the bed.

Satsana fan duct with cr-touch bracket cutout for 4010 or 4020 fans, compatible with Ender 3 and Ender 3 v2.

Remix of ebyaskawa Ender 3 Pro Umbilical Support Bracket. ...I only added bl touch mount to it.

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

The evolutionary spool holder is designed to work seamlessly with multiple Creality printers, including the CR-10, CR-10s, CR-10s Pro, and Ender models. ...It's built to fit onto the original bracket of these machines.

I recently purchased this sensor:...

... the Ender 3/Ender 3 v2 printer with a MicroSwiss direct drive installed. ...This allows for usage of the Cr-Touch without a printed part, you'll need to use the ender 3 cr touch mount bracket and screw through the fan duct.Printed with PETG at .20mm

... Ender 3/Ender 3 v2 printer with a MicroSwiss direct drive installed. ...This allows for usage of the Cr-Touch without a printed part, you'll need to use the ender 3 cr touch mount bracket and screw through the fan duct.Printed with PETG at .20mm 

Remixed two designs together; unlike all other designs, first one didn't interfere with CR touch, 2nd had Ender logo I liked.

This is a cover designed for the Creality Ender-3 Pro/V2 Touch Screen.Watch the video here: https://youtu.be/rg1y4zzKOXg

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket. Category: 3D Printer Parts

This is a custom direct drive setup designed for the Ender 3, CR10, CR10S, CR10S4, and CR10S5 printers, utilizing a BMG extruder and an E3D V6 hotend. The primary intention was to couple the BMG extruder directly to the E3D V6 hotend without any PTFE...