cr touch ender 2 pro 3d models

I had to pad out my CR Touch with the stock setup to get proper clearance for z-offset by adding a couple of fat washers between the sensor and the mounting posts. I carried this over with the NG, but I went ahead and used a M3 nut instead of...

This is a modification of the Left Side BL Touch Mount for the BlokHead so that it's usable with a CR Touch. Depending on how things all line up for you, you'll need spacers to ensure the CR Touch is long enough. I used nuts and it works fine. ...

A remix of the 0 Y Sprite CR Touch mount to fit a V2. ...Ends up closer to 1 Y offset.

Edit it online https://www.tinkercad.com/things/5kl5t0HJbxx remix of (FIX) Satsana Fan Duct Remix for Micro Swiss Direct Drive Extruder - Creality CR-10 & Ender 3 Printers + CR Touch https://www.thingiverse.com/thing:5183321 Offset: X: -48 Y: -9 i...

will need to change the m3 bolt to a m3x8mm and 2 are needed for the cr touch. i did find that i needed to place a nut at the bottom of the v2 mount to allow for clearance. this is my first attemp and think i will do another version so it has more...

I noticed that this design had not been properly adapted to the CR Touch without anything extra added onto the design and decided this would be very useful considering the benefits of the CR Touch compared to the BL Touch. The probe offset should...

I used tinkercad and a cadgrab model to make this model compatible with the cr touch without decreasing the build volume. ...Read the original's desc for more details.

I used tinkercad and a cadgrab model to make this model compatible with the cr touch without decreasing the build volume. ...Read the original's desc for more details.

Remixed the original 5015 fan duct and slimmed the left duct down to make room for the CR Touch Also added a slot for an M3 nut to utilize the rear mounting hole from the original duct

Remixed the BLTouch mount to fit Creality's own CR Touch model. Printed with 100% infill (because I always print parts with 100% infill but it's up to you) with support on. Use same nuts and M3 bolts as BL touch model. ... left side offsets X:-61,...

I trimmed the front of this cover down so it will clear a BL Touch or a CR Touch when it auto homes. I also created a wire slot on the back rather than a hole out the side like the original. ...This is for ease of installation and I also feel like it...

I'm currently using the Hemera V6/Colcano Part Cooling Duct by Hangtight but I haven't tested this CR Touch version as I have a BLTouch: https://www.thingiverse.com/thing:4042492 With my modified mount for additional Z axis adjustment to account for...

That's a spare part for Ender 2 Pro Belt Tensioner.Essa é uma peça de reposição para o esticador da correia da Ender 2 Pro.

This is a remix of moodyfools edit that allows the Satsana duct to work with the new CR Touch and Steel Mount that is included with the kit. ...Like the other Satsana Ducts, you must flip the belt ends on the Gantry to where the brass ends are facing...

Good day,Welcome to my profile, full of models and miniatures :-)I'm an Ainon3Dprint model maker and printerI have a holder for CR touch, BL touch, 3D touch probes for you. ...There are two variants, one of which is the original creality dimensions and...

are you struggeling with calibrating the CR touch or any other sort of probe, chanses are that your x axis may be twisted. this makes the distance between nossle and the probe to bed different. x offset doesnt really matter, but if this is the case...

I had remixed this Satsana Fan shroud from several others model and after creating it I had discovered the stock Cr touch placement would interfere with the part cooling fan. So I had made a different mount so to basically flip it around so the side...

... did not perform very well. So I remixed an existing (hopefully proven) file to fit to this DD Kit. It has an attachment point for a CR Touch. I am not sure if a BL Touch will fit, becuase it has a shorter throw I think. ... Maybe it helps someone

I've increased the dimensions of the top bracket and added some more brackets to the bottom (v2).On the ABL mount I've cut out a slot on the top to make the wires fit for a CR Touch. I've also made a slot along the bottom for it's cables to route...

This is a BIQU H2 mount on the latest Ender 3 v2 mount.

Redesigned bracket to clear CR TouchDesigned an extension bracket to get a better view of the nozzleRedesigned camera housing for an Arducam Pi Camera with Motorized Lens (https://a.co/d/eDK9wCd)

Remixed https://www.thingiverse.com/thing:4647793 Added a draft angle to the face that mounts to the stock Ender 3 v2 carriage plate as my Hemera, and therefore nozzle, were not square to the axis/bed. The draft angle "pushes" the bottom of the...

Hobbled together something that will work to properly allow the NG extruder to hit the X-Axis limit switch on the Ender 3 V2 Neo from Creality. ...The switch style is that of the Ender 3 S-1 model which lays flat instead of vertical.

... my own brain…) and still I was able to reduce the weight (nearly 20%). ... should fit on the Sidewinder X1/X2 and Genius too. bed level sensor offset: x_offset:-2.5 y_offset:30 thanks to user h19x51 for the main work. ...For me i fine tuned it :-)

I made this to attach a 1" travel dial indicator to my Ender 3 V2. It requires a CRTouch bracket (though not necessarily the sensor itself). It mounts above the bracket using the brackets mounting bolts. The indicator I am using is this one...

Printed on Ender 5 proresolution 0.2mminfill 100%wall 1.2mm

ALSO, REPORT ME IF YOU FOUND ANY ERROR.** Important notes -------- * Parts were tested for parts mutual matchings and collisions and thus they are accurate to some extent, although I didn't print any parts (except...

I thought the Ender 2 Pro looked like it had an animal-like face, so I gave it some ears. Best paired with googly eyes (not included) You can use filament swapping for the color change. Onshape link Category: 3D Printer Accessories

I thought the Ender 2 Pro looked like it had an animal-like face, so I gave it some ears. Best paired with googly eyes (not included) You can use filament swapping for the color change. ... [Onshape...

I wanted some rails to perfectly fit my Ender 2 pro after getting bits in it. These cover the screws and print without supports (I added a tiiiiny support to one end you can snap off). ...I've also included the rail in its whole length if you have...