cr touch ender 2 pro 3d models

The **CR Touch** support is placed as close as possible to the nozzle so in the ***Configuration.h*** for the ***Marlin*** firmware the values for the *NOZZLE_TO_PROBE_OFFSET* should be: ``` #define NOZZLE_TO_PROBE_OFFSET { -37, -7, 0 } ``` A new...

... in length. ... I also added a hole to access the screw inside, and a brace (untested) for added support of the CR Touch to keep it steadier. I printed it with supports from bed only. ...and even at a .28 layer height, mine turned out great.

Cr touch mount for creality ender 3 v2.

Ender 6 CR touch mount for DDX V3 with Mosquito Hotend

First and foremost I want to start with a **WARNING:** While this does work for the Ender 3 Pro It will require a little bit of trimming of the plastic around one side of the mounting support on the CR Touch. The tolerance and clearance are very...

https://www.printables.com/model/255772-cr-touch-left-side-mount-for-ender-3s1s1-proI redesigned it for my Ender 3 S1 Pro.Reasons for remixThe original had its X-offset being-55.5mm however this didn't allow me enough room for my X-axis to reach for...

#### CR Touch Mount for the Satsana Remix for the Ender 3 V2 I couldn't find a remix for the CR-Touch so I created it myself. #### Why? ... Because the original mount didn't have room for the connector of the CR-Touch, and if you tried to put the...

Remixed version of the Ender 3 CRTouch Mount by Plasmid0.Almost same mount for the CR-Touch from Creality. ...But I added additional cutouts for head shield ears.

You will need 2 x 18mm (ish) m3 bolts 4 x m3 nuts 2 x m3 lock washers Fit the bolts through the CR Touch and lock on with a nut on each. Slot the bolts into the mount, add a lock washer on each, then lock on with a nut on each. The middle nuts are...

Fun duct turbin 5015 + cr touch

... the Creality Sermoon V1 Pro and the Creality CR-Touch bed leveling sensor. ... More information about the [configuration of Klipper and the Creality Sermoon V1 Pro](https://www.hyperio.ch/blog/creality-sermoon-v1-with-cr-touch-and-klipper.html). ...

Modified Version of the Creality Ender 3 S1 Shroud with the BL Touch and CR Touch mount moved to the right side Update 1: Added the hole for the gear tensioner back and missed the gab for the metal backet to slot into Update 2: Fixed some...

# Description I altered the BL-Touch Petsfang Ender-3 mount to be compatible with the CR-Touch. The little notch above the screw hole I found was not actually necessary, but it does not hurt anything either, so I left it in out of laziness. I...

... use when upgrading a Creality Ender 3 V2 Neo with a Titan direct drive kit. ...The bracket will attach to the two offset holes on the x axis motion assembly and will hold the CR-Touch device as well as the accelerometer that comes with the Sonic Pad.

This is a versatile BL-Touch support that's simple to print with the Creality CR-10S PRO. It prints quickly, mounts effortlessly, and adjusts smoothly. ...For optimal results, it's recommended to use PLA filament instead of PETG due to its superior...

This is a simple, no fuss cover for the Creality CR-10S Pro touch screen. It sits neatly within the front case cavity, just above the screen. I printed this using three perimeters, laid facing up with supports. ...Filament is PLA+ at 205° with a 60°...

I have both the CR touch AND the Octoprint Touchscreen on my Ender 3 - and a bracket wasn't available that would work with both of those things. So I modified the original bracket to suit my needs, and it worked out pretty well! ... This is the...

I decided to design a CR Touch mount for my Ender 3 MAX as my CR Touch never came with mounts at all. I searched for a little while for pre-made ones but didn't find anything I really liked so decided I would attempt my own one. It was designed in...

Just chopped off a bit of the mount to clear the CR Touch.

I want to use this shroud https://www.thingiverse.com/thing:5404679 (needed to remix it) and this cooling ducts https://www.thingiverse.com/thing:5137512 After printing the cooling system did not fit with my CR Touch for a few millimeters. ...I took...

I saw a few CR-5 users wanting to upgrade to the Pro H BL touch. I have not printed this myself and am unsure if HT materials will hold up. I can update this later with a thermal test on the surface of the carriage. ... For now though, test at...

I created this reinforced version, I added CR Touch, available 2 versions of direct, standard or Redrex. For the front conveyor use epoxy glue, use self-tapping screws 2.9x10 mm. ...Silent 4010 or 4020 fans can be used, under the front conveyor you can...

Here I present my CR touch mount for my Ender 5.Unfortunately, none of the models online has pleased me and met my conditions,because with the standard mount you unfortunately break the sensor if you move the axes to the very left front. ...My first...

This is for an Ender 3 v2 printer with CR Touch. I made the hot end connector three pieces to be able to move when performing auto bed leveling. The original design prevented the hot end from traveling the entire length of the x axis which is...

Sorry for the hiccups.-----------------------------------------------------------------------------LDO Apogee for Phaetus Dragonfly BMS hotend (incl mount for Orbiter 2.0 and cr/bl touch) for Ender 5 x-axis carriage plate. I wasn't happy with a few...

The original mount by Properprinting was awesome but it didn't have a spot for a CR/BL touch sensor, so I added one! ...

original BL touch was mounted in a way that blocks the mounting to x carriage mount is from thingiverse making it difficult to adjust too toolhead i am also using cr touch mount comes from satana before using voron i was using this mount. ...thanks...

this is a remix for this thingy https://www.thingiverse.com/thing:4921720 I've added a slot to allow for CR-touch installation and lowered the connection by 2mm to avoid print head hitting the bed

Made this mount to deal with the included mount in the kit not clearing the part cooling fan. ...Uses all provided screws that come with the CR touch kit.

### Hardware Holes for the CR Touch are designed for M3 Screws & Nuts like my CR Touch Bracket ### Probe offset: -49, -9 *I'm sure it's not perfect, but it's fairly close.* ### Print Settings See below **Please leave comments and such with any...