cr touch ender 2 pro 3d models

https://www.thingiverse.com/thing:2759439 This mount is shortened and adjusted to bring the CR Touch closer to the bed compared to the original. The original design did not get my CR Touch close enough to detect the bed, this design should fix that...

This mount took inspiration from the mount included with the CR-Touch that fits with the Ender3.This model uses the same dimensions as the parent remix, however it was made fresh in Tinkercad...

https://www.thingiverse.com/thing:2759439This mount is shortened and adjusted to bring the CR Touch closer to the bed compared to the original.The original design did not get my CR Touch close enough to detect the bed, this design should fix that for...

CR Touch sensor mount and spacer. ... The center of the holes are 18mm distant and the holes are 1,5mm of radius (3mm of diameter).

I liked the shroud I found by chubbyzook (thing: 4821813). ...So, when it was time for a CR Touch, I remixed this design.

This Bracket is specifically designed for this direct drive. ...print with the open slide slot for the CR Touch wiring on the build plate to save using supports

... the other ones, so the other designs did not work for me. I designed it for the Ender 2 Pro, but I believe it should work for Ender 3 also if you have your filament spool attached on the side. ... Use 20mm M3 bolts to hold the sensor in place.

($1.50)https://www.aliexpress.us/item/2251832780928351.htmlMy runout sensor seems to be a bit different that the other ones, so the other designs did not work for me.I designed it for the Ender 2 Pro, but I believe it should work for Ender 3 also if...

This is a Satsana "inspired" design for the Ender-2 with the stock fan duct and CRTouch/BLTouch mount. (CRTouch/BLTouch is optional and doesn't need to be installed.) Designed to be printed without needing supports. This should allow for full...

This clip uses the 2 existing mounting points of the CR Touch probe. You will require 2 longer M3 screws and 2 M3 nuts to install it. I recommend printing at 100% infill. The bracket can be printed flat. The clip should be printed on its side with...

I searched the web and don't find Ender2 Pro Bracket So I chose This as a Remix https://www.thingiverse.com/thing:3052488 Hope you Guys Like it!

Drop in replacement for weak stock Ender2 pro 150w power suppy. ... bom: SUSWE 300W 24V 12.5A https://aliexpress.com/item/1005003394055957.html 8010 24v fan IEC 320 C14 inlet (AC-07) 14mm round on/off switch M3/M4/M5 hot melt inserts some...

This design allows: - to adapt to a direct drive and bowden system - to be 15% * faster to print than the original Satsana - to be 17% * lighter - to be installed with the original fans of the Ender 5 Cumulating the benefits of Satsana: - better...

This design allows: - to adapt to a direct drive and bowden system - to be 15% * faster to print than the original Satsana - to be 17% * lighter - to be installed with the original fans of the Ender 5 Cumulating the benefits of Satsana: - better...

Hello, I designed this simple remix of @pmayer enclosure to adapt an skr 2 inside. ... I just modified the front panel, so take the rest of the case from original maker.

The housing is fully compatible with the housings for the right side. ...If ferrules are used, these wires have to be connected before mounting the Duet 2 Wifi in the case, otherwise it becomes very tricky.

The BTT SKR 2 uses the same bolt patterns as the SKR Turbo v1.3/1.4, but it has an additional USB port. ...This remix adds a slot for the USB.

... inside corners and diamond cutouts added to the case. I wanted the rounded compartments so it would be easier to get small parts out with my big fingers. The diamond cutouts in the case took 2 hours off the print time and reduced filament use.

I remixed the Support Touch-mi CR-10 from Thingiverse (https://www.thingiverse.com/thing:3350748) for my own CR-10S printer. ...I made the X-axis cart a bit larger, about 2mm more than usual, and also modified the magnet holder so it doesn't spin...

This is a combo shroud that allows you to mount both a Noctua NF-A4x20 FLX 40mm fan and a BL-Touch auto-leveler to your Ender 3 Pro. You will need four M3 screws (approximately 1.5 cm in length) and nuts in order to secure the fan to the shroud.

Hope you like it.These parts require some screws to attach to Ender 3 V2 and other required components, the list will be given below. Find the components at your nearest local store or click on the link I have given below. Please attention that I am...

 Print the knobs then use an m4 bolt and screw it a little into the m4x8x6 insert. 2. Add just a little Kwik JB Weld onto the insert.3. Turn the wheel upside down and then place the insert into the knob while holding the m4 bolt. Take out bolt.4. ...Let...

The BTT SKR 2 uses the same bolt patterns as the SKR Turbo v1.3/1.4, but it has an additional USB port. ...This remix adds a slot for the USB.</p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>FLSun Super Racer</p> <p class="detail-setting...

... a little. The printing needs a well-calibrated device, I used PETG filament. In addition, 2 ball bearings with an outer diameter of 12 mm, an inner diameter of 8 mm and a height of 3.5 mm are required. ... The grinding noise is gone now...

this is a remix for the problem im facing in my ender 3 pro with sprite and crtouvh not leveling the whole bed for some reason

Made insert nuts suitable for ZeroG project inserts (they are larger than EVA 2.4 default) Made necessary holes for CR/BL Touch hanger. Materials: 7 Inserts M3 X D5.0 X L4.0 M3 Nuts: 2x 16mm 2x 8mm 3x 25mm for 10mm fan or 3x 35mm for...

Improving leveling knobs for the Ender-2 printer requires a thoughtful approach. Two distinct variants exist - one designed for front screws, which is slightly larger in size to accommodate two screws, and another smaller variant suited for the rear...

Better leveling knobs designed specifically for Ender-2 machines. Two variants exist: a larger size suitable for two front screws and a smaller size intended for the rear screw, with the latter requiring careful adjustment to avoid hitting the...

Here are the hardware components used: * 2 M3 bolts for secure attachment of the BL Touch mount * 2 M3 bolts to fasten the BL Touch probe securely * 2 M3 nuts to stabilize the BL Touch probe * 2 M3 washers for added stability and reduced wear on the...

<p>I had been using a satsana shroud I found over on thingiverse by chubbyzook (Thing: 4821813). ...I couldn't find one with the propper CR Touch mount, so I remixed the one I was already using.Print with supports touching buildplate