cr touch ender 2 pro 3d models

The ender 2 pro can be equipped with a CR Touch auto bed leveler. Only creality does not yet have a mounting bracket for the Ender 2 Pro. ...So you will have to print one yourself.

Ich freue mich drauf. Wenn ihr Lust habt könnt ihr auch gerne mal in meiner Facebook-Gruppe vorbeischauen: Ender2 Pro Community Print Settings Printer Brand: Creality Printer: Ender 2 Rafts: No Supports: Yes Resolution: 0,12 Infill: 15 Filament:...

If you are interested, you can also visit my Facebook group: Ender2 Pro Community Deutsch: Ich habe hier einen Remix des BLTouch Halters gemacht da ich mir einen CR-Touch bestellt hatte.  Ich wollte aber zusätzlich das original Hotendcover behalten...

I'm looking forward to it. If you are interested, you can also visit my Facebook group: Ender2 Pro Community Deutsch: Ich habe hier einen Remix des BLTouch Halters gemacht da ich mir einen CR-Touch bestellt hatte.  Ich wollte aber zusätzlich das...

I've remixed a Satsana 5015 to fit with the Ender 2 Pro.Some Modifications made:Optional Orbiter V2 Direct Drive mountFixed CR Touch mount (My klipper offsets - X:-44.5, Y: -13.5 Z:1)Optional ADXL mount on the side (1x M3 Hole)Print with nozzle fan...

I've remixed a Satsana 5015 to fit with the Ender 2 Pro.Some Modifications made:Optional Orbiter V2 Direct Drive mountFixed CR Touch mount (My klipper offsets - X:-44.5, Y: -13.5 Z:1)Optional ADXL mount on the side (1x M3 Hole)Print with nozzle fan...

This is a Satsana "inspired" design for the Ender-2 with a CR-Touch Mount and a 5015 fan duct. Designed to be printed without needing supports. This should allow for full travel of the bed without any mods for that. My CR-Touch to nozzle offsets...

Made a little more sturdy version of https://www.thingiverse.com/thing:5219978. ...That version was moving to much. Specially adapted for https://www.thingiverse.com/thing:5867916. So NOT for the standard cooling duct of the Ender 2 Pro.

I made the part that attaches to the carriage plate a bit thinner so you can use shorter screws (that's all I had at the time so I couldn't install the original version).

I originally came across this model from Printibles user 3dprint, then I found the original model on Thingiverse that had the .step files and I ended up editing the model in Fusion360 to fit the Ender 2 Pro and a Cr-touch/Bltouch. FeaturesActive part...

Print time was about 1h 15min to 2h and fits the stock 4010 fan on the Ender 2 Pro. The three bolts needed are the same bolts that secured the stock cover (two long for the fan and one short to secure the mount to the mounting plate). TO INSTALL:...

Do modulu byli přidané snímače ( CR-Touch ,Pinda probe V1) a pod ventilátor jsem nalepil Led pásek 12V ktery je ovladaný od ventilátorů + odpor 620 ohm

The stock Ender 2 Pro fan and housing works fine, but it's impossible to see the nozzle while printing.  Also needed a mount for the CR-Touch/BL-Touch. ...Had one for the stock setup and worked great, but this fan mount interfered with it since it used...

Adapted dmatos's BL Touch mount for Creality's new CR Touch probe for my Ender-3 Pro. I thickened the mount's arm for added strength and to slightly lower the probe height, added a piece that sits against the left edge of the Micro-Swiss frame to...

I found that the original didn't quite fit properly and triggered the X axis endstop too early so I have made a little cut out for it so it fits correctly.

Remix of another design that adds the additional 4mm offset for the longer Creality Spider hot end.

A remix of the [Mini Satsana + CR Touch](https://www.thingiverse.com/thing:5254926) file by [hobie2987](https://www.thingiverse.com/hobie2987). The original [Mini Satsana](https://www.thingiverse.com/thing:5160364) design had some wayward vertices...

This direct drive conversion for ender 3 pro. ...pacifically designed for cr touch. ...I made this in tinkcad.

Petsfang Mount for CR Touch and Sonic Pad G Sensor ADXK345 for Ender 3 Pro using stock hotend plate

this a direct drive for a ender 3 pro with cr touch ( that my first try off publish thing )

The bracket has been designed to accommodate a CR touch on an ender 3 pro with the Satsana 3d printed fan shroud. You should not need to print this with any supports, 3 or 4 walls should be fine. ...I ended up needing to adjust my Z offset to exactly...

Remixed version of the Ender 3 Pro BLTouch Mount by puturai. mount that can be used for the CR-Touch from creality. works with the included screws but needs 2x M3 Nut. Nothing more to add than that it works well for me. ...This one needs some supports...

Ender CR touch mount. ... I lost/miss placed my CR touch mount for my ender 3 pro, made up this quick sturdy design.

... setups. This can be printed in PLA. But PETG is recommended for longevity. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 75% Filament: eSun PETG White Category: 3D Printer Accessories

The original works nice for bl-touch, but does not enough room for cr touch wiring. So, i made a ugly, quick, hacky cut to fit my needs. ... Printed in ABS, 30% infill, on a modded Ender 3 gen 1.

Madau's original design worked great and was nice and strong, but when I got a CR-Touch probe I discovered they do not play nicely together. I removed a small piece to make room for the CR-Touch and thatdoes make the bracket slightly less stable, so...

CR touch bracket for Ender 7

I am using this on an Ender-5 Pro, but it is probably also compatible with the Ender-5, and probably not with the Ender-5 Plus. Let me know yea or nay in the comments and I'll update this description to confirm. Also it should still be compatible...

*UPDATE* I have a newer design posted that mounts on the left side and does not require a longer cable.https://www.printables.com/model/257460-ender-3-s1-zero-offset-cr-touch-mount Like many others I was having issues with the automatic bed...

CR Touch offsets are : x_offset: -46.5 y_offset: 0 Hardware for CR-touch probe: 2x M3 nuts With KLIPPER You can modify the offset in the "printer.cfg" file: [bltouch] x_offset: -46,5 y_offset: 0 You may also need to adjust your mesh if you get an...