cr 6 se direct drive 3d models

I required a way to lift the sensor to the BMG Extruder on the CR-6 SE using the filament sensor from https://www.thingiverse.com/thing:4635094. I no longer had the original casing. This was my first ever own 3d print design, so there might be...

I'm working on building an upgraded spool support for the CR-6 SE with bearings, but as a step along the road, this is a basic replacement for the spool support. It twist-locks into the arm that comes with this model (and presumably other) Creality...

CR-6 SE Filament roller that uses 608-2RS bearings for maximum smoothness! Screws into filament arm the same way the stock one does, but with almost zero friction on the filament roll. Print with bottom of the frame on the print bed, and the...

... with the breakout board cover. Straight forward print, just print with the fan mount on the bed. No support needed. Current version only for 40x40x10mm fan. Printed with the Creality CR-6 SE which is still not selectable in Thingiverse.

A replacement drawer tray for the CR-6 SE to take a Raspberry Pi 3A+ and a PiJack power adapter board (which will take up to 32v input) to run OctoPrint. The USB ‘extension’ is wired leaving out the V+ connection so the Pi can’t back power the...

Remixed the Ender 3 Webcam mount by aallensd for my CR-6 to mount to the Rails instead and added support to the arm.

This bracket was required due to space constraints (as shown in pictures), my printer could only fit on an angle due to the width increase of the standard spool mount position. Print Settings Printer Brand: Creality Printer: CR-X Rafts: No Supports:...

My CR-6 SE printer is installed at such a height and angle from my seated position that I have difficulty seeing the blue LED that signals activation of the bed probe. While musing to myself how I might bring that signal out where I could see it,...

Part cooling fan for the Creality CR6 SE that uses the stock blower flan but directs the airflow closer to the nozzle. ... Version for 40mm quiet fans: https://www.thingiverse.com/thing:4777287

I have found a this previous design somewhere but it was no where near fitting the CR-6 so I have made it fit, you can use the original screws, takes only couple minutes to install

I had to tweak it a bit since the CR-6 SE has closed slots on the front, and the rear side is blocked (already used for the dual Z axis screw stabilizers) REQUIRED PARTS: ==================== * *Printed Brackets* (left and right separately) *...

Inspired by 3Deth's and RICBRU's work, I've designed my own CR-6 SE air intake with two-tone air deflectors.I'm not sure if this surpresses any noise...it's just designed to look cool while redirecting the vent to pull colder air from above the hot...

Filament: Prusament ASA Black Notes: Yeah, it's weird I didn't print these on the CR-6 SE itself, but I already had the Prusa printer set up with the 0.6 nozzle which gets us down to just two perimeters on each layer. Printed 8 of these in 9...

May work all 4040 profiles, but Cr-6 has some obstacles at rear right side. ...So i remixed Foot-3-RR part for my printer.</p><p><strong>Print Settings:</strong></p><p>0.2 layer height<br>%15 infill (rectilinear)<br>3 walls&nbsp;<br>4 top/bottom...

[drawer_org]: https://www.thingiverse.com/thing:4612526 [419mining]: https://www.thingiverse.com/419mining/designs [scad]: OpenScAD.org # Nozzles Holder for CR-6 SE Drawer Organizer This is an accessory for the [drawer organizer][drawer_org] on...

The top part of the stock cover is a little loose, but it can't back out anymore.&nbsp;I used longer M3 bolts since the stock ones were too short.&nbsp;I printed in PETG on the CR-6 at 40% infill. ...I didn't use supports, there was a little drooping on...

Part cooling fan for the Creality CR6 SE that uses the stock blower flan but directs the airflow closer to the nozzle. ...Version for 40mm quiet fans: https://www.thingiverse.com/thing:4777287 Print Settings Printer Brand: Creality Printer: Ender 3...

Support for the Bowden tube on CR6-SE Hotend

Hello, petit cache de protection, pour cacher se moche câble.

This is the useful accessory that is missing from the Creality CR-6 SE. A simple device to automatically turn off the printer after printing has finished. If you don't trust yourself to solder this cable yourself, because you are working on a...

The 6burner V4 can be used either in bowden mode or in direct drive by installing a direct drive extruder, 4 different can be mounted. The extruder is installed on the x-carriage and let the strain gauge dedicated to the hotend installed (stock,...

... Mounts with a tab in the front and a M3x16 or M3x20 bolt from the back through the Orbiter mount. Remixed the left circuit cover and added a version without text cutout and one with CR-6 logo (design: https://www.thingiverse.com/thing:4778892).

Tray organizer for the CR-6SE, it is a simple print, no suports needed.

remix of SE Bed Handle w/ camera mount with rounded edges uses original screws

I remix the Endstop Cover for the CR6-SE with the Logo of the company Sachsenring that build the iconic Trabant in east germany.

I took the CR-6 drawer that takman29 created ( https://www.thingiverse.com/thing:4656033 ) and the Z-cover that RICBRU created ( https://www.thingiverse.com/thing:4670030 ) and just simply combined them, then fixed the drawers to fit. I couldn't...

Petg 40% 0.20

This is a holder for full size Sd cards. ...It is designed to be mounted on the CR6-Se printer in the extrusions. ... Print with the SD card slots down for best results.

A mount for the filament sensor of Creality CR-10S printers when using a direct drive extruder, or as a spool holder on top if mounted in the opposite direction. Two versions are available: V1 with the filament guide and V2 without the filament...

I'm using this: https://www.thingiverse.com/thing:4669393 And lastly, I printed a spacer which is also included in the files to increase the length of the parts cooler tip so that it doesn't blow directly at the heater block with the added height. I...