cr 6 se direct drive 3d models
552450 3d models found related to cr 6 se direct drive.
thingiverse
This almost-direct drive bracket requires the purchase of a Titan (clone or otherwise) and the appropriate stepper motor. In my case I used the following: A Titan clone extruder: https://www.amazon.de/gp/product/B07MZKY9WJ The thinnest...
thingiverse
Sonic Pad Bracket sensor with CR Touch and Direct Drive.EASY TO INSTALL ----- USE SAME SUPPORT FOR CR TOUCH OR BL TOUCH
thingiverse
CR-10 S4 Direct Drive Extruder Mount Rev. ...01 Watch this video on YouTube: https://youtu.be/drFjboCvHf8
thingiverse
This direct drive conversion for ender 3 pro. pacifically designed for cr touch. ...I made this in tinkcad.
thingiverse
this a direct drive for a ender 3 pro with cr touch ( that my first try off publish thing )
thingiverse
Designed a custom CR-10 Direct Drive mount by merging ideas from two pre-existing Thingiverse mounts and tailoring it to meet my specific requirements.
thingiverse
Cable chain mounts for X Endstop and Bondtech Direct Drive for Creality (Cr-10 / Ender) printers Uses this cable chain: https://www.thingiverse.com/thing:2920060
prusaprinters
Updated Print Settings Printer: Creality CR-6 SE Rafts: NoSupports: Yes Resolution: 0.2mmInfill: 50 Filament: BIQU Matte PLA Olive green Notes: You need a little bit of support for the part that screws into the X-carriage. Post-Printing...
thingiverse
## Bill of materials - One [Bondtech LGX](https://www.bondtech.se/product/lgx-large-gears-extruder/) with either the direct drive or bowden interface plug attached - 2x M3x14 screws - 2x M3x10 screws If using a [reverse bowden mount to feed...
thingiverse
I have a mirrored BMG extruder that I bought from Bondtech as part of the [Creality3D CR-10S PRO Extruder Kit](https://www.bondtech.se/en/product/creality-cr-10s-pro-extruder-kit/) I found this [CR10S Pro direct drive by...
thingiverse
Designed this clip to hold the Creality Laser to snap on directly to the direct drive extruder on the CR-10 V3 E3D Direct Drive Extruder Printer. There are two version one with holes and one without. ...The holes are to direct mount the D-B500F...
thingiverse
Just a simple cable support to organize the cables so they don't get damaged when upgrading CR-10 with direct drive system from Micro swiss. Works good. ... Mounted easly with some cable ties around the stepper motor and cables.
thingiverse
Mount for a TH3D EZABL on a CR-10 (S) using a Microswiss Direct Drive extruder and all metal hotend. Cutout to be use with a Fang mounting plate. ... Offsets: X: -64.5 Y: -8
thingiverse
This work with a inexpensive drive plate to make a direct drive setup for a Cr-10 or Tornado. You just grind away a little of the plate to make it so a stepper motor will seat properly. Link to Drive plate.
thingiverse
I have the Microswiss Direct Drive / Hotend combo on my CR-10S. https://store.micro-swiss.com/products/micro-swiss-direct-drive-extruder. The Petsfang didn't fit on my printer so I modified the base to allow it to fit. ... I haven't modified the...
thingiverse
This fit's tight around the cable plug on the head. You may need to scale the STL in you preferred slicer to make it fit properly. Support on motor is for 13mm cable. ... Support on motor 2 is for 22mm cable.
thingiverse
This clip was design for people who has no space in front of the Printer. ...
prusaprinters
SummaryI have a mirrored BMG extruder that I bought from Bondtech as part of the Creality3D CR-10S PRO Extruder KitI found this CR10S Pro direct drive by Achocho conversion that I could remix to work with the mirrored extruder. I also added a Bowden...
thingiverse
CRELITY 3D CR-6 SE Original CR6-SE hot end 40mm fan adapter part. ... for replace damaged part
prusaprinters
When I first installed my direct drive bracket I couldn't fully get the fan duct back on properly cause the two parts interfered with each other.Best to print with PETG with supports.Credit to Eric Anastas for the original design...
thingiverse
This is a direct drive mount that doubles as an X carriage for the CR-10S printer. I have not tested it on the CR-10 model, but it fits a Fang style blower perfectly: https://www.thingiverse.com/thing:2606026. Two 25mm M3 bolts are all you need to...
thingiverse
Creality CR-6 SE Folding Spool holder clone, fits all Creality printers with same aluminium framing
thingiverse
Quick functional mounting plate to raspberry pi model [x]-B v-rail Creality CR-6 SE
thingiverse
This is my first crack at a cable anchor/tie for my CR-10 V2, which is using a direct drive mount and had no convenient place to tie wires. ...I'm definitely still working on this one, but the current revision works rather well.
thingiverse
CR 10 Direct Drive Extruder Mod Single Part, revamped from another 2 part design. The extruder is now firmly centered over the print head, a significant improvement over its predecessor. A unique dual fan setup catches your eye on the far side of...
thingiverse
I'm testing Bantamount, a free modular mount for CR-10, and discovered that it's relatively simple to modify into a direct drive extruder. ... The results are impressive - it works seamlessly but still requires fine-tuning on the right side to ensure...