cr 4020 3d models

*TPU Fan Mount or Dampener for 4010 Axial 4020 Radial Fan* Sometime the cheap fan itself is quiet enough, but when attached to sometime the vibration will get amplified and get really noisy. The Noctua have rubber mount for their fan which...

I was searching for a functional adapter for my 4020 fan to try out with my Kossel Plus, but the designs I found weren't suitable for optimal airflow. So, I designed one myself. The fan can be securely attached using double-sided adhesive tape...

4020 Blower duct optimised for printing in ABS. removable pad to help with adhesion, supports from build platform only if you have good bridging settings. Single side part cooling using a 4010 blower. Left and right fixing options. Blower...

This is a remix of the Ender 3 Pro Fan Shroud for 4020 Fan w/ BL Touch Mount by jass_on. Its remixed so it will fit the stock Ender 5.exept for the fan mounting. I've made it a little wider to fit the cables from the hot end and removed the ABL...

I swiftly fabricated a custom ABL mount to accommodate the existing sensor, ensuring it clears the endstop housing even with the dual 4020 duct in place. By setting an offset of minus 58 units in the X-axis and minus 10 units in the Y-axis, I...

Due to size constraints, I originally designed the 4020 mount, then switched to 2020.There's one quirk which I'm unsure of: The camera/display ports sit under the board, and the arm obstructs that area. You can definitely plug in cables around it,...

It features a modified design that accommodates a large 4020 fan, similar to those found in high-end computer coolers like Noctua. The hotend cover boasts a spacious 19mm hole perfect for EZ-ABL sensors, ensuring precise temperature readings. ...This...

Simple dual 4020 blower fan cooling duct for BIQU H2. Simple and low profile, it is height adjustable via the 2 mounting slots that connect directly to the H2. print gets fairly thin by the duct so .4mm nozzle or smaller would be best, but I...

It is designed to hold two 4020 fans, not the more common 5015, this trying to keep the mount as small as I could (it is not small either way) Printing: You might need a few support on at least one of the borders, just to make sure the cavity for...

The screw hole for holding the 4020 blower fans on the original HMG5 lightweight ducts did not line up with the holes on the 4020 blowers I purchased. This corrects that issue by enlarging the top of the 'arm' that holds the fan and then...

It is designed to hold two 4020 fans, not the more common 5015, this trying to keep the mount as small as I could (it is not small either way) Printing: You might need a few support on at least one of the borders, just to make sure the cavity for...

Creality Wifi Box Case 4020 Mount Creality Wifi Box Case (and lid) firm fit for 4020 profile. Couldn't find a proper one and I did it myself. Take care that the case fits 4020 profile very firmly. You may break or slide through the corners of the...

It is designed to hold two 4020 fans, not the more common 5015, this trying to keep the mount as small as I could (it is not small either way) Printing: You might need a few support on at least one of the borders, just to make sure the cavity for...

Buy it printed from me: https://3dchanh.com/my-store/ols/products/sidewinder-x1-ultimate-cooler-4020-radial. Note that you will need to print the compact extruder cover, as the stock one is too large. ... **Hardware Requirements:** 4020 Version 2:...

Buy it printed from me: https://3dchanh.com/my-store/ols/products/sidewinder-x1-ultimate-cooler-4020-radial Note you will need to print the compact extruder cover, the stock one is too big. ... Hardware Needed: 4020 Version 2: ( BLTouch: X 58, Y -36 )...

I'm dissatisfied with the upgrade options available for my 40mm hotend cooling fan, so I designed this custom mount to accommodate a quieter, more powerful 4020 blower fan instead. This innovative mount fits snugly over the stock mounting holes of...

This is the Satsana fan duct where the part cooling fan is a 4020 one. To know if supports are required or not, please refer to the first link of the three above. For BLTouch, there is a gap in the mounting side that allows the stock metal bracket...

**** If you make it and it works, please click like :) **** I couldn't find a suitable cooling duct for my 4020 blower that came with my A10T. So I found one that was close and hacked it up. I don't have the link for the original or I would give...

I designed the shroud to use a 4020 fan which is a huge improvement over the original fan. It reuses the original screws and it stays clear of everything. You may need to adjust the depth of the screw holes depending on your print. ... I have...

These are cable clips/ducts that snap onto 2020, 3030, and 4020 extrusions. Adjust your slicer's Z height to suit your needs. By default, a 10 mm height produces a robust clip. To create a duct, set the desired length as the Z height. The image...

**** If you make it and it works, please click like :) **** I couldn't find a suitable cooling duct for my 4020 blower that came with my A10T. So I found one that was close and hacked it up. I don't have the link for the original or I would give...

Edit: Updated and uploaded a V2.5 for the fan part, less radius but better droop resistance A cyclone fan modified for the 4020 fan found on the SV01 and edited on the heatsink clip to allow room for the nut found near the v6/OG hotend. Uses all OG...

This customized cyclone fan is tailored specifically for the 4020 fan found on the SV01, while also incorporating modifications to the heatsink clip to accommodate the nut located near the v6/OG hotend. The design utilizes all original parts and...

Made a minor modification to the provided 4020 adapter for HangTight's Creality cooler so it doesn't block the part cooler's optimal position. *NOTE: The model looks okay despite being a simplified mesh converted to brep and modified in order to...

Slightly modified remix of the version modified for the larger 4020 fan thats factory on the creality CR10s-pro. I quickly smoothed and beveled inside and outside of blower intake seat for more "laminar" flow, and a somewhat factory look. Not...

This is a customized holder for the Sapphire PRO printer, specifically designed as FAN 4020. EDIT: Version 4 of this design has been created. I have redesigned the pull holes to direct them more precisely towards the heatbed. Edit December 29,...

I didn't have a 5015 fan but I did have a 4020 for some reason, so I modified the duct to fit and adjusted and cleaned up the mounting holes. I also moved the mount for the original TronXY inductive bed probe so that the holes weren't cut into the...

__________ Simple "Air assist" for k40 alike lasers for 4020 blower fans Works well enough for this type of machine. ... <br><br><br><Center><big><big><b> If you like my work <a rel="nofollow" href="http://paypal.com/paypalme/maxdarkdog"><img...

I use a larger effector in my delta printer, which requires either three 4020 fans or 4010 fans for optimal performance. This setup is specifically designed to work seamlessly with the E3D V6 1.75mm hotend and its clones, as well as carriages of 40mm...

Printhead for Flying Bear Ghost 4s with two turbo blowers model 4020. Printed all parts in ABS material, achieving a 100% coverage and scaling up by 102%. The tensioner and its seat must be filed down for easy gliding. An M3 nut is used for the...