cr 200b 3d models

19938 3d models found related to cr 200b.
BLTouch CR-200B
BLTouch CR-200B
thingiverse

BLTouch holder for CR-200B

cr-200b partcooler
cr-200b partcooler
thingiverse

I own a CR-200b and the default partcooler is not so good. ... I found the design of ShaunTheBaa and changed it, so it fits on the cr-200b. And it works like a charm! ... Thx ShaunTheBaa for sharing V2 is a cleaned-up version

CR-200B Stand Increase
CR-200B Stand Increase
cults3d

Since the Stand of the CR-200B is very low, the fan can not suck enough air to cool the circuit board. Especially if a better fan is installed. ... With this stand, the printer is placed higher up(+2,5cm), which significantly contributes to the...

CR-200B Cooling Duct
CR-200B Cooling Duct
thingiverse

Yet another cooling duct for creality CR-200B. This is my first upload to thingiverse. Its made without support and does not require other components than the two screws that removed when unmounting the original cooling duct. This design...

CR-200B Stand Increase
CR-200B Stand Increase
thingiverse

Since the Stand of the CR-200B is very low, the fan can not suck enough air to cool the circuit board. Especially if a better fan is installed. ... With this stand, the printer is placed higher up(+2,5cm, which significantly contributes to the...

CR-200B Stand Increase
CR-200B Stand Increase
myminifactory

Since the Stand of the CR-200B is very low, the fan can not suck enough air to cool the circuit board. Especially if a better fan is installed. ... With this stand, the printer is placed higher up(+2,5cm, which significantly contributes to the cooling...

CR_200B_Extruder_Mount
CR_200B_Extruder_Mount
thingiverse

This is a new carriage with provisions to mount a Orbitor extruder to the CR-200B. The wire channel has been moved back a bit allow the Orbitor mounting screw. All of the mounting holes such as hotend, hotend fan, original cover mounting holes and...

CR-200B endoscope mount
CR-200B endoscope mount
thingiverse

I measured it for mounting on the CR-200B without the metal shroud cage. In the picture, I mounted using the angled version which allows a view a little from above. I've included the flat version where it will provide a flatter view giving you a...

Support CR-Touch CR-200B
Support CR-Touch CR-200B
thingiverse

Support for CR-Touch developed for CR-200B hotend.

Creality CR-200B / CR-200B Pro Top Spacer / Raiser
Creality CR-200B / CR-200B Pro Top Spacer / Raiser
prusaprinters

An upgrade for the Creality CR-200B 3D printer. ...It's a spacer that elevates the top dome, preventing the cables from rubbing against its upper part.

4020 blower fan CR-200B
4020 blower fan CR-200B
thingiverse

Better fan for CR-200B 4020 Fan: https://www.bastelgarage.ch/creality-4020-bauteillufter-cr-10s-pro-max Printed in ASA: https://www.bastelgarage.ch/easa-schwarz-filament-1-75mm-1kg-esun

4020 blower fan CR-200B
4020 blower fan CR-200B
cults3d

Better fan for CR-200B 4020 Fan: https://www.bastelgarage.ch/creality-4020-bauteillufter-cr-10s-pro-max Printed in ASA: https://www.bastelgarage.ch/easa-schwarz-filament-1-75mm-1kg-esun

Cr 200B Bearing Spool Holder
Cr 200B Bearing Spool Holder
thingiverse

Remixed the original so that the threading would align with the notches in the back of the Cr-200B (the original was tilted to the side). ...Also put the axle together for a single piece print.

CR-200B 120mm fan mount
CR-200B 120mm fan mount
thingiverse

The CR-200B has two fans doing basically one one job. Replace both the 5015 radial and 4020 axial inside the case with a 12V 120mm axial. I mounted pushing air out the bottom so less chance for cool air to introduce into the printing chamber. ...If you...

CR Touch CR-200b
CR Touch CR-200b
thingiverse

I made the following changes: - made the screw holes smaller to fit the m3 screws included with the CR Touch - made a cutout so that the cable connector on the CR Touch is accessible - removed the top cable brackets so it can be printed without...

cr 200b orbiter 1.5 mount
cr 200b orbiter 1.5 mount
grabcad

cr 200b orbiter 1.5 mount

Creality CR-200B GT2 Belt Clip
Creality CR-200B GT2 Belt Clip
thingiverse

This is a belt retention clip for the Creality CR-200B.

CR-200B Filament sensor bracket for BMG
CR-200B Filament sensor bracket for BMG
thingiverse

Small bracket to hold the filament runout sensor when using a Bondtech (BMG) extruder on a CR-200B

CR-200B fan holder for extruder gear
CR-200B fan holder for extruder gear
thingiverse

CR-200B 3D printer extruder stepper motor is encloses without possibility to good disipate heat. ...This model will hold fan near extruder gear.

cr 200b orbiter 2.0 mount
cr 200b orbiter 2.0 mount
thingiverse

cr 200b orbiter 2.0 mount. Holes were designed to put a brass inserts. ...The top two holes front side is for 2mm

CR-200B XY Axis Bearing Retainer
CR-200B XY Axis Bearing Retainer
thingiverse

Bearing retainers for the CR-200B, 3 of mine were broken and 4th one was cracked, Replacing with the brittle under supported ones even if you could find them seemed pointless. I designed these they fit great. You will need to use M3X12 screws for...

CR-200B_Part_Cooling_Duct_Upgrade
CR-200B_Part_Cooling_Duct_Upgrade
thingiverse

Part cooling duct upgrade for CR-200B. Directs airflow more at nozzle. Uses all stock screws to mount. I am using a Microswiss all metal cr10 hot end mounted as stock hot end is same length within a few mm so duct should work with stock hot end...

Cr-200B Creality Fan Upgrade Schwalbe
Cr-200B Creality Fan Upgrade Schwalbe
thingiverse

It is modular and variable so it should fit all upgrade Hotends for the CR-200B It can also be used as a base for other upgrade Parts for example a BL-touch or other cooling fan nozzle solutions. I call it Schwalbe. I just connected the other...

5015 blower fan duct CR-200B/Ender3
5015 blower fan duct CR-200B/Ender3
thingiverse

Originally designed for CR-200B but I guess can also fit Ender 3 since it has a very similar head design (not the V2!). The fan duct allows to hold a 5015 blower fan which improves a lot the cooling performance compared to the stock 4010 fan. ...

Vent cover for Creality CR-200B
Vent cover for Creality CR-200B
thingiverse

It covers the ~200mm dual fan exhaust area on the back of the Creality CR-200B and provides an outflow that works well with a 3" vinyl flex duct. This is a rough STL, put together as a quick fix. You may need supports to print it well, depending...

CR-200B 5015 blower part cooling
CR-200B 5015 blower part cooling
thingiverse

I modifed it enough to allow the duct/fan to slide under the CR-200B chassis and enough clearance to avoid the bed retention screw. Check the posted pictures, I was able to fully travel the bed without any hitting anything. NOTE, I reverse the...

CR-200B CRTouch Mount Left
CR-200B CRTouch Mount Left
cults3d

Shoppping List: CRTouch: https://www.bastelgarage.ch/cr-touch-auto-leveling-kit-fur-4-2-2-4-2-7-mainboard or BLTOuch: https://www.bastelgarage.ch/bltouch-3-1-automatischer-nivellierungssensor...

CR-200B CRTouch Mount Left
CR-200B CRTouch Mount Left
thingiverse

Shoppping List: CRTouch: https://www.bastelgarage.ch/cr-touch-auto-leveling-kit-fur-4-2-2-4-2-7-mainboard or BLTOuch: https://www.bastelgarage.ch/bltouch-3-1-automatischer-nivellierungssensor...

Creality CR-200B Printer
Creality CR-200B Printer
grabcad

Creality 3D is a professional 3d printer manufacturer, specializing in integrating 3d printing software research, 3d printer design.They recently launched a brand-new model of their printer #CR200B, here is Cad file of Enclosure of same that...

CR-200B Fan Upgrade Schwalbe CR-Touch (Remix)
CR-200B Fan Upgrade Schwalbe CR-Touch (Remix)
thingiverse

My Printer: Creality CR-200B Creality Sonic Pad Phaetus Dragonfly BMS CR-Touch