cr 10s pro v2 upgrades 3d models

This is an extremely simple fix to let you fit a more accurate 8mm probe (sensing range 2mm) to the CR-10s Pro, so that the probe is thermally separated from the nozzle. For me this is a significant improvement over the LJ18A3-8-Z/BX. The probe I...

The standard automatic bed levelling sensor that comes with the CR-10s Pro v1 is an 18mm diameter capacitative probe, which unfortunately has poor repeatability due to its sensitivity to environmental factors. Many people replace this with an...

Step 6: Select upgrade firmware and navigate to CR10SPro_1.1.9_B5.hex (For the CR-10S Pro) or CR-X_1.1.9_B5.hex (for the CR-X) and upload. Cura told me this failed, but it didn't. Power on and off the machine and the Tiny Machines logo will show and...

I'm reworking TallNHairyDave's magnetic base for the CR-10S Pro of hamkers' camera arm, giving it a fresh spin. I love the original design, but I had two major issues: 1) The initial magnet size wasn't readily available on Amazon, so I swapped them...

I designed a small housing to shield the buck converters needed when swapping out the CR-10s Pro's cooling and extruder cooling fans for Noctua or other 12v fans. The enclosure attaches to the back of the extruder motor, where the black plate is,...

- [Original Filament Holder](https://www.thingiverse.com/thing:3209211), print all of these parts except the holder - [Side mount for CR-10S Pro](https://www.thingiverse.com/thing:3790189) - [Version that's 90 degree...

... and grounds between multiple interfaces. In order to take full advantage of the Duet features I designed the [CR-10S Pro Custom Transfer Board](https://github.com/ReXT3D/cr-10s-pro-mods/tree/duet3d) that allows all signals to be fully independent.

Here are two 5015 fan mounts for a Bullseye Mount designed specifically for the CR-10S PRO. You can find them on Thingiverse at https://www.thingiverse.com/thing:3439109. I created these mounts using two identical 5015 fans, one with a thicker wall...

Extensions accommodate a 310x310x3 glass bed on a CR-10S Pro. This is a standard glass bed size, but the oem clips don't quite fit. With these installed, you won't lose any print area as the printer doesn't reach the back of the bed. Simply slide...

I remixed the original filament roller for my cr-10s pro because slicing with Cura 4.1 and having the Creawesome mod installed caused certain parts to not fit properly, specifically the bearing wouldn't fit into the wheel and neither would the body...

The CR-10s Pro is a fantastic 3D printer that can be modified to support LED lighting with the addition of a switch-case and other necessary components. To get started, you will need to acquire several key items, including the switch itself, which...

fan mounts for creality cr-10s pro with the creality spider 3.0 hotend. all 6 holes on the hotend fan mount for 40x40x10 fan will need to be reamed out with a drill bit .098 (4 holes) for easier fan install and .191 (2 holes) to press fit the mount...

This is a mount I created to use the Bigtreetech Smart Filament Sensor encoder wheel with a CR-10S Pro. Directions: Remove the stock filament sensor. Place the mount over the filament sensor mount posts, they will align. Use 4 x M3x6mm...

This is just a remixed version of the base piece to fit on the side of a CR-10s Pro. Specific to this version: The slots are a little too long on the base giving me the ability to move the mount up or down to get the right angle. I mounted...

My bed cable snapped after several large prints, so I came up with this fix for my Creality CR-10s PRO. You can see the broken bed power cord in the picture and video below. The solution involves adding a chain that adjusts the cable angle while...

This is a mount I created to use the Bigtreetech Smart Filament Sensor encoder wheel with a CR-10S Pro. Directions: Remove the stock filament sensor. Place the mount over the filament sensor mount posts, they will align. Use 4 x M3x6mm...

Here's a quick DIY solution I came up with that I think you might find helpful - a guide for wiring your blTouch along the ribbon cable on my CR-10S PRO printer. The idea was to create a simple way to manage the blTouch wires, and here's how I made...

Here's a revised Filament guide designed for my CR-10s pro, taking into account that most existing guides assume the Spool holder is mounted on top of the machine. Since I've already printed a Spool holder to place on the left side of the table, I...

This is my custom x-gantry adaptor designed to convert a Creality CR-10s Pro into a direct-drive machine that's compatible with Hero ME Gen 5 adapters. I created this to centralize all cables in one point and secure them with clamps, making it easy...

In other words, while it was optimized for my setup with stock hot end and Microswiss nozzle, it should work well with all CR-10S Pro units. Please do not print this in PLA. Even though there is good clearance between the duct and the heater...

SD extension cable mount for firmware upgrade LCD screen so you don't have to open the bottom every time you want to update the LCD screen -For a better fit in Cura scales to 102% -Clean the holes for the bolts with a 2 mm drill -Use two bolts and...

... added stability, melt the nut into the hexagon using a soldering iron. Apply a piece of tape between the metal housing and the SD card holder to prevent cable damage. Note: No adjustments or drilling is necessary on your CR 10S Pro metal housing.

Here's an upgrade to my previous cable cover specifically designed for CR-10s Pros with direct drive conversions like my Hemera. After upgrading to direct drive, I was left with a tangled mess of wiring under and around the breakout board - but also...

Synchronize your CR-10S Pro Z Axis steppers without sacrificing print capacity or risking damage to your printer! **Edit 3/3/19:** By request, I've added V2_Beta (untested at this point) to enable socket head cap screws for mounting the stepper...

It securely bolts inside the body of a Creality CR-10S Pro and may also work with other printers. It attaches where the stock 4020 blower fan is typically located. The case becomes even more useful when paired with a fan mount like this one found on...

This is a Raspberry pi mount for the CR-10s pro with optional camera mount. It is designed to be mounted on either side or on the back of your 3D-Printer.</p> <p>The mount is extremly easily mount/removable for optimal flexibility.</p> <p>These are...

This is a Raspberry pi mount designed specifically for the CR-10s pro with an optional camera mount. It can be mounted on either side or at the back of your 3D printer for maximum versatility. The mount is extremely easy to install and remove,...

SummaryThis design is a remix of TallNHairyDave's magnetic base for the CR-10S Pro of Hamkers' camera arm.I love the design, but I had two problems:1) I could not source the same size magnets from Amazon used in the original. So instead, I switched...

I wanted to add some cable chains to my CR-10S Pro and found some pretty good designes online, but I wanted some changes on everything. I used johnniewhiskey´s chain links on both chains, but modified them slightly, so they can be printed without...

I've been using my custom-made fang style fan duct since the original one snapped after a few prints - decided to share it as there aren't many other models available that offer airflow from opposite sides on the stock CR-10S Pro configuration, which...