cr 10s pro v2 upgrades 3d models

Here's a custom-made mounting bracket designed specifically for the digital indicator from Harbor Freight, model #63613. This solution aims to facilitate easier bed tram adjustments. To assemble this mount, you'll need one 1" 1/4 bolt and a...

I received some valuable input from the team, so I adjusted the design to a new angle, V2, which ensures that the airflow is directed straight into the nozzle fan duct of the CR-10S PRO. ...This should result in improved flow and increased durability,...

A strain relief for CR-10S pro with a centered cable, I needed to reposition the strain relief when i upgraded the bed heater to a AC 220V.The reason for the screenshot from thingiverse is because i am moving all my designs from there.

A strain relief for CR-10S pro with a centered cable, I needed to reposition the strain relief when i upgraded the bed heater to a AC 220V.The reason for the screenshot from thingiverse is because i am moving all my designs from there.

I added a second tower in, especially if you run a CR-10s Pro V2 or CR-10 Max which have a BL-Touch. you want to tie the wires to the somehow more rigid PTFE tube. The base with the cutout allows you to travel further to the right without crashing...

Bigtreetech PI TFT43 mount for the CR-10S Pro adapter I would add a photo but thingiverse is beeing difficult as usual

This is a mount for filament sensor of CR-10S Pro using Bondtech DDX. ... One with cable ties and one without.

If you own a CR-10S Pro, be sure to install the quiet fan upgrades mentioned at: https://www.youtube.com/watch?v=RRbvASlom4A&t=29s It is well worth your time and money to make this upgrade. This design was inspired by Thingiverse's 3399705. ...

I successfully installed it on my Ender 5 Plus, but it should also work seamlessly on the CR 10S PRO V1 or V2. The same bolts are utilized for this purpose. ...If you want to achieve even greater stability, I highly recommend using two metal inserts...

This is the mount I designed when upgrading my Creality CR-10S Pro with a Hemera direct drive extruder, BLTouch, 40x40x20 heat sink cooling fan and 4015 part cooling fan. I kept the stock filament sensor and moved it to the mount. ... I used this...

This is a coupler reinforcement that gets mounted onto the extruder of a CR-10S Pro or CR-10 MAX. ...The purpose of this part is to prevent the bowden or capricorn tube from slipping out of the coupler.

Soporte multipropósito para Creality CR-10s PRO. Recambio de Asa de soporte de bobina de filamento. Base para USB y MicroSD. Soporte extendido para alicates y pinzas. Multipurpose support for Creality CR-10s PRO. Replacement of filament spool...

Déflecteur d'air pour refroidir efficacement un hotend micro-microswiss avec le ventilateur d'origine de l'imprimante Creality CR-10s pro. Il peut être fixé avec les vis du ventilateur d'origine. Fanduct for micro-swiss hotend installed on Creality...

Air deflector to efficiently cool a micro-swiss hotend with the original fan of the Creality CR-10s pro printer. It can be fixed with the original fan screws. Fanduct for micro-swiss hotend installed on Creality CR-10s pro. ...Don't need new screws.

Spool Holder designed specifically for the CR-10S Pro with bearings, crafted to perfectly complement the following Thingiverse design: https://www.thingiverse.com/thing:3579392. The necessary bearings are two 608ZZ units, which will provide smooth...

This is a remix of the side Filament Spool Holder by builditfull, made to work with the Creality CR-10S PRO. It mounts on the side screws, and on the 2020 side-rail. By having the spool on the side, filament guides are not necessary anymore, and the...

Ender 10S Upgrade Power Supply Control Unit Stand Best Creality CR-10/S/V2 Upgrades & Mods elevates the control unit about 2.8 inch - 7.3 cm helps in good unit ventilation and better cooling easier access to the sd card avoid grounding electric...

Remixed from the Voron Switchwire x carriage, this mods lets you mount a Stealthburner toolhead on a CR-10s pro (tested) it could work with other CR-10 and Ender 3 style printers (not tested)I run klipper but I use a octopus board and two IDC30...

* See (https://www.thingiverse.com/thing:4801958) for my BTT TFT70 case * See (https://www.thingiverse.com/thing:4689019) for my BTT PI TFT50 case ### BTT TFT43 Case for the CR-10S Pro v2 This will allow you to mount the Big Tree Tech (BTT) TFT43...

I found the initial design interesting, but I added a no bearing wheel and a additional guide so the filament will not detach from the wheel, when the tension is reduced. ...Also the original sensor bracket is not allowing the filament to be pulled out...

I have uploaded a drilling guide to change the ABL mounting holes on the original plate to Suit the version 2 plate ABL mounts. BL Touch Offset { -38, -2, 0 } Z offset approximately -3.10 The eccentric nut and bolt need to be assembled...

Noctua Fan https://www.amazon.com/gp/product/B009NQLT0M/ref=as_li_tl?ie=UTF8&tag=antontech-20&camp=1789&creative=9325&linkCode=as2&creativeASIN=B009NQLT0M&linkId=b1c2b6436b675b1f38f7e136c009af7e Power Converter ...

This is a dial gauge holder that mounts onto the extruder of the printer. ... It uses friction so no hardware or modifications to the printer are required.

All the Creality printers come with this ugly QR Code on the printer, mine was even peeled up in the corners. This simple <1h print covers it up. I made 2 versions; mine fits the 41.5mm one but maybe your printer isn't too precise and you need the...

used 2x 12v noctua fans powered in series to replace the single 4020mm board fan

This is a dial gauge holder that mounts onto the extruder of the printer. ... It uses friction so no hardware or modifications to the printer are required.

In South Africa, sourcing the exact 760mm belt required for the z-axis sync mod is a daunting task. Undeterred, I discovered an 852mm belt in stock and designed this innovative tensioner system to seamlessly integrate with the aluminium extrusions.

These are parts for a cable chain from another user. I just re-thrown the "Cable_chain_bottom_bracket_new part.STL" part to be able to install my own filament holder. The old part "Cable_chain_bottom_bracket_old part.STL" does not work for this. You...

I found the initial design interesting, but I added a no bearing wheel and a additional guide so the filament will not detach from the wheel, when the tension is reduced. ... Also the original sensor bracket is not allowing the filament to be pulled out...

I remixed the original to print the tops of the ducts separately so that the inner surface was smooth as possible for better air flow. I attached them with super glue. ...Printed in PETG it worked great and was quieter than the original.