cr 10s pro upgrades 3d models

I designed a small housing to shield the buck converters needed when swapping out the CR-10s Pro's cooling and extruder cooling fans for Noctua or other 12v fans. The enclosure attaches to the back of the extruder motor, where the black plate is,...

This is a mount I created to use the Bigtreetech Smart Filament Sensor encoder wheel with a CR-10S Pro. Directions: Remove the stock filament sensor. Place the mount over the filament sensor mount posts, they will align. Use 4 x M3x6mm...

- [Original Filament Holder](https://www.thingiverse.com/thing:3209211), print all of these parts except the holder - [Side mount for CR-10S Pro](https://www.thingiverse.com/thing:3790189) - [Version that's 90 degree...

I remixed the original filament roller for my cr-10s pro because slicing with Cura 4.1 and having the Creawesome mod installed caused certain parts to not fit properly, specifically the bearing wouldn't fit into the wheel and neither would the body...

This is just a remixed version of the base piece to fit on the side of a CR-10s Pro. Specific to this version: The slots are a little too long on the base giving me the ability to move the mount up or down to get the right angle. I mounted...

fan mounts for creality cr-10s pro with the creality spider 3.0 hotend. all 6 holes on the hotend fan mount for 40x40x10 fan will need to be reamed out with a drill bit .098 (4 holes) for easier fan install and .191 (2 holes) to press fit the mount...

The current Hero Me Gen5 gantry adapter has some minor flaws and fails to fit snugly onto the CR-10s Pro V2 gantry plate without extensive modifications, but this remix aims to rectify these issues: * The two holes used to attach the gantry adapter...

This is a mount I created to use the Bigtreetech Smart Filament Sensor encoder wheel with a CR-10S Pro. Directions: Remove the stock filament sensor. Place the mount over the filament sensor mount posts, they will align. Use 4 x M3x6mm...

In other words, while it was optimized for my setup with stock hot end and Microswiss nozzle, it should work well with all CR-10S Pro units. Please do not print this in PLA. Even though there is good clearance between the duct and the heater...

**For the Creality CR-10S Pro and the Creality CR-10S Pro V2 only. I have the V2.** This is a remix of [Anar's CR10-S Pro Frame Brace (light version)](https://www.thingiverse.com/thing:4000797) 10mm bottom frame brackets. IMO, his light version remix...

Here's an upgrade to my previous cable cover specifically designed for CR-10s Pros with direct drive conversions like my Hemera. After upgrading to direct drive, I was left with a tangled mess of wiring under and around the breakout board - but also...

4020 radial fan guard specifically for Creality CR-10S Pro, working with stock fan duct and its variants. Also works perfectly with Hero Me 4020 air pipe/fan duct。</p> <p>Mount with</p> <p>2x M3*18 screws</p> <p>1x M3*20 screw</p> <p>bolts are needed...

Remix of boulwarek's file to fit for the glass bed of the CR-10S Pro V2. Essentially it's just 5mm lower than the original. This ensures that no matter how you tighten the bed springs the x-axis gantry doesn't hit the stepper motors of the z-axis.

A simple, yet more accurate re-creation of the X gantry calibration tool provided by Creality that ships with the CR-10S Pro V2. I measured Creality's version with calipers and it was 99.60mm. I assume it is supposed to be 100mm, so I created my...

Noctua NF-A4x20 Fan Mount and Shroud for Creality CR-10S Pro V2 Custom Cover to Conceal Noctua's Beige Fan Custom Fan Shroud Boosts Airflow on OEM Hotend...

LED Light Strip Mount for the Top Gantry - specifically for CR-10S Pro v1/v2 - May/should work on other printers, just check length of rail. For me the [original](https://www.thingiverse.com/thing:3312232) (thanks @KenNox) was the best design I...

I designed this to fit my CR-10S Pro V2 after having tried a couple of other designs that were available online and never being quite satisfied with them. I have swapped out the stock blower fan for a pair of 5015 blower fans (cheap from Amazon).

It securely bolts inside the body of a Creality CR-10S Pro and may also work with other printers. It attaches where the stock 4020 blower fan is typically located. The case becomes even more useful when paired with a fan mount like this one found on...

This is a Raspberry pi mount for the CR-10s pro with optional camera mount. It is designed to be mounted on either side or on the back of your 3D-Printer.</p> <p>The mount is extremly easily mount/removable for optimal flexibility.</p> <p>These are...

This is a Raspberry pi mount designed specifically for the CR-10s pro with an optional camera mount. It can be mounted on either side or at the back of your 3D printer for maximum versatility. The mount is extremely easy to install and remove,...

So I uploaded a v2, which should help dissipate heat better.* My version of a perfect Creality CR-10S Pro V2 Tool Holder. You will need 2x M5 25mm bolts with T-Nuts. Remove some screws from the printer's base and slide the holder's left 'fin'...

SummaryThis design is a remix of TallNHairyDave's magnetic base for the CR-10S Pro of Hamkers' camera arm.I love the design, but I had two problems:1) I could not source the same size magnets from Amazon used in the original. So instead, I switched...

I wanted to add some cable chains to my CR-10S Pro and found some pretty good designes online, but I wanted some changes on everything. I used johnniewhiskey´s chain links on both chains, but modified them slightly, so they can be printed without...

I've been using my custom-made fang style fan duct since the original one snapped after a few prints - decided to share it as there aren't many other models available that offer airflow from opposite sides on the stock CR-10S Pro configuration, which...

https://youtu.be/TMVGrmwluwY I designed this piece to hold a PTFE tube as a reverse bowden filament guide for my Creality CR-10S Pro V2. I have a filament dryer next to the machine and want to have the PTFE guide the filament out of the dryer and...

What ==================== Remixed parts for my CR-10S Pro V2 based on the following: * [Hero Me Gen 6 Base ](https://www.thingiverse.com/thing:3182917) * [ABL plate](https://www.thingiverse.com/thing:4888736) I haven't opted to use the remix button...

What Remixed parts for my CR-10S Pro V2 based on the following: Hero Me Gen 6 Base ABL plate I haven't opted to use the remix button as I can only credit one design. Why By the time you put the full Hero Me adapter/base plate and squeeze an ABL plate...

Synchronize your CR-10S Pro Z Axis steppers without sacrificing print capacity or risking damage to your printer! **Edit 3/3/19:** By request, I've added V2_Beta (untested at this point) to enable socket head cap screws for mounting the stepper...

This adapter is based on Jrjy3 work - https://www.printables.com/model/452757-creality-cr-10s-pro-pro-v2-e3d-revo-cr-adapter It mount to the original Creality CR10S hot-nozzle bracket. Exact fit to the two-bracket lug for stability and to prevent...

this is a remix of a few peoples cr-10 project, i converted it to the Pro V2 and cut the heat funnel for the bl touch,   Also if your looking for the noc fans you can combine a 12v fan with a 12v LED to get 24v power which this machine is running...