cr 10s max 3d models

I've included a helpful diagram of the CR-10S Creality 2.0 board, which shows how the fan is wired to the bed heater output MOSFET terminals. This might seem counterintuitive, but it's not really an issue in practice. Materials needed: * Wire...

It's not rare for a CR-10 or CR-10s to arrive with a Z axis that's slightly out of whack. This can sometimes cause your Z screw to get stuck or jump around, leading to some serious frustration. The problem lies in the way the stepper motor is mounted...

I made this project because I got tired of the filament getting stuck in the Bowden tube while printing on my stock Creality CR-10s printer, even after upgrading to a BondTech extruder kit. With the direct drive approach, the filament is pushed...

CR-10S Pro Cable Chain Instructions. May 22, 2020 - Added a wider version for the V2 model. For assembly instructions, refer to the zip file containing photos. Assemble the chain by using the die and boss as shown in the photo. Start with the base...

This remix features a few tweaks in order to better fit onto a CR-10s Pro V2. It is highly suggested that prior to install, the fan shroud be mounted onto the base first, the two mount screws on the base be pre-threaded, and the four hot end fan...

https://www.ebay.com.au/itm/224167492478 Hemera Upgrade, CR-10S Pro 26-08-2020 Added .step File for V2 Plate Bl Touch Mount 20-08-2020 Updated Flat Pattern Added in .dxf File and BL Touch Mount for Updated Plate Included 30-07-2020 Get Ready for...

This is a fully printable enclosure design for the CR-10s Pro. Approximately 2kg of filament (I used PLA) and around 150 hours of print time are required. It's designed specifically for 1/8" wall panels, with hardboard used for all but the front,...

I recently acquired a Creality CR-10S 3D printer that performed flawlessly straight out of the box, until about halfway through its initial prints, when I encountered some issues with the Z-axis functionality. Specifically, the left Z motor would...

Bonjour, Sur demande voici un lettrage "Cr-10S Pro V2" en 4 versions différentes : 1 - 2mm d'épaisseur non-attaché 2 - 1mm d'épaisseur non-attaché 3 - 2mm d'épaisseur attaché 4 - 1mm d'épaisseur attaché Pensez à vous abonner à mon compte pour être au...

From the original design, I'm using (4) L brackets instead of (2), which eliminates tapping and threading the bottom of the CR-10s or CR-10 frame entirely. The brackets are secured using M5 T-Nuts and M5 machine screws. ... Below are links to purchase...

I was a bit let down by the original Creality filament sensor that came with the CR-10S, so I designed my own with a snap-on lid. No more screw-on lid, making it easy to pop open without tools to check if something's wrong inside, like a small piece...

This upgrade is specifically designed for the CR-10S spool holder, but it can easily be adapted to similar spool holders as well. The key features of this design are: - No extra parts required - Reuses the stock spool holder - Reduces friction for...

I upgraded MarvinPound Sticky’s Creality CR-10S CR10 frame brace stiffener, achieving no loss of Z height! https://www.thingiverse.com/thing:2808613 I customized it with additional support on both the front and back sides. I reinforced them to...

Be aware that it might only fit the first type of filament sensor and extruder motor, my cr-10s model is from late 2017.\ I was tired of the original filament sensor housing slipping when inserting filament; it was only being held on by the housing...

Renfort et stabilisation du portique de la CR-10s Pro Voyant le portique osciller sensiblement pendant l'impression avec des saccades rapides , j'ai décidé de renforcer la structure. Après quelques réflexions j'ai choisis d'adopter cette solution qui...

Renforcement et stabilisation du portique de la CR-10s Pro La structure de l'imprimante oscillait sensiblement pendant l'impression, avec des saccades rapides. J'ai donc décidé de renforcer la structure pour la stabiliser. Après quelques réflexions,...

This design was inspired by the model referenced in source by Sdsyc and is based on the Microsoft Lifecam HD 6000, modified to work seamlessly with the Creality CR-10 for supervising 3D prints. ...It can be easily operated using a computer or via...

Orange, There are many nice designs about CR-10/S filament guides, but I couldn't find one that is minimal and holds the extruder wires nicely. With this design, you won't need to remove the screws to put it into position. ...It simply slides right in...

The parts that build the walls of the base require the following: 60mm_support_Front_corner_mk2.stl - one for each corner 150mm_angle_vent_panel_mk2.stl - two for each side 85mm_center_support_side_panel.stl - one needed for each side...

Here's a customized GoPro mount designed specifically for the CR-10 3D printer. I carefully crafted this model to eliminate the need to remove leveling screws, instead relying on friction to secure it in place. This makes installation and removal a...

This filiment holder/dispenser is designed to fit snugly onto a Creality CR-10 S pro 3D printer using the OEM angle bracket and quick disconnect nut, providing a seamless integration. Three 22mm bearings are utilized, which can be sourced from local...

I wanted a sleek, lightweight frame brace design for my CR-10. I found Rick's design, which I really liked, but it's in inches and I found it a bit challenging to install since he designed sockets for the nuts at both ends. So I created my own frame...

CR-10S PRO Upgrade

CR-10S-Bondtech-Mosquito_Mount_-_Bl_Touch

Fan replacement for motherboard CR-10S Pro

Filament senzor case for Creality CR-10s

The evolutionary spool holder is designed to work seamlessly with multiple Creality printers, including the CR-10, CR-10s, CR-10s Pro, and Ender models. ...It's built to fit onto the original bracket of these machines.

Kamera Halter für Unifi G3 Flex am CR-10S

Modification of the original to fit the CR-10s

Here is a bigger version of gulfcoast_robotics' handle bar freshly modeled and sized for the CR-10 Max. ... I'd suggest support on this one, and you'll need the Max to print it due to its size.