cr 10s max 3d models

This design was crafted to seamlessly integrate with the stock hotbed of a Creality Cr-10S Pro. After succumbing to numerous rookie mistakes that rendered my original bed unusable, I opted for a brand new Wham Bam Flexible Build System bed as a...

Hi everyone, This optimized fan duct for Creality CR-10S PRO 3D printer is ready for printing. For best results, print it using ABS or PETG. A support structure is required, as shown in the image above. Printing with 100% infill and a layer height of...

For owners of the CR-10S Pro who have drybox and are seeking to connect the tube from the drybox to the extruder, there is currently no viable solution available. The tube simply hangs loose, swinging randomly. To resolve this issue, you can install...

I've got a modified CR-10s Pro with a Microswiss AllMetal Hotend and a BLTouch Sensor. I purchased a Zimpure Filter System to combat UFP and VOC emission. Since no suction head was available for the cr10spro from the seller, I designed this one...

This part helps straighten the filament before it enters the switch on the Creality CR-10s Pro printer. Be cautious when printing, as you're new to this process - print at your own risk. You might need to shave a little from the finished piece,...

I edited it to fit with the filament sensor that comes with the Creality CR-10S. I made some improvements on the hole sizes and the part where you screw it into place, making it a bit bigger to prevent breaking of the small parts. The original...

A new upgrade is available for the CR-10s Pro frame brace. This update fixes a slicing issue that was present in S3D and also includes cosmetic upgrades. To perform this upgrade, you will need the following items: * Two M8 Threaded Rods (75cm each)...

... the print cannot enter the fan. To secure the duct in place, I utilized Scotch double-sided glue. This design is specifically tailored for the Creality CR-10S PRO, but it should also fit other fan guards with an outer frame of approximately 43mm.

After reprinting the original Creality fan duct for the CR 10S Pro because the bottom was too rough and could cause problems, I also noticed a slight deformation of the beak due to heat from contact with the hot-end. In order not to distort the...

... cooling fan(50mmx10mm), but removed the 20mmx20mm exaust fan from the control box. Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Rigid ink PLA Category: 3D Printer Accessories

Premise: After having reprinted the original Creality fan duct (for CR 10S Pro) because the bottom was too rough and could create problems, I also noticed a slight deformation of the beak due to heat from contact with the hot-end (see photo)...

This design was made to retrofit onto the stock hot bed of a Creality Cr-10S Pro. I made (as pictured) a lot of newbie 3D-printing mistakes that ruined this bed, so I decided to by a new Wham Bam Flexible Build System bed to replace it. After the new...

This is a custom filament adapter designed specifically for the CR-10S printer, tailored to accommodate Hatchbox 1.75mm PLA filament. After experimenting with various adapters and taking on the challenge of designing my own, I'm pleased to share the...

This is a premium filament guide designed specifically for the Creality CR-10s Pro. It's engineered to prevent tangles by featuring a pivoting feed tube that adjusts its angle in real-time as the Z axis moves upwards. This innovative design ensures...

This is a precision-designed spool holder replacement for the Creality CR-10s Pro printer. It perfectly accommodates spools with compact diameter center holes, such as high-quality filament from AMZ3D. To ensure maximum strength, print it with at...

This guide is designed specifically for use with the Creality CR-10s Pro. It prevents tangles by featuring a pivoting feed tube that adjusts its angle automatically when the Z axis reaches higher heights. The mount requires no screws or removal of...

Hi, Wanted to create a Raspberry Pi holder that fits perfectly on my CR-10S Pro. I used this case - https://www.thingiverse.com/thing:2786498, then designed the side mount that clicks easily into place. I carefully drilled holes at the bottom of the...

I needed a tool rack that wouldn't obstruct my print height on my CR-10S Pro, as most designs seem to do. I stumbled upon this fantastic design (https://www.thingiverse.com/thing:2607518), but it lacked a few features I wanted. To fix this, I added...

I recently installed Cornely_Cool's fantastic belt tensioners on my CR-10s (https://www.thingiverse.com/thing:2869114 and https://www.thingiverse.com/thing:2854971). After making adjustments and increasing belt tightness a little, I began to worry...

I recently installed Cornely_Cool's awesome belt tensioners on my CR-10s (https://www.thingiverse.com/thing:2869114 and https://www.thingiverse.com/thing:2854971). After installing them and increasing belt tightness a little, I started worrying about...

I have included the files for the PSU enclosure as complete or in 2 parts depending on the size of printer you are printing these parts on, The 2 part files fit on a Prusa MK3 sized bed and the complete parts will fit on a CR-10s. Printing I have...

I've included the files for the PSU enclosure in two separate versions: one complete version that can fit on a CR-10s-sized printing bed, and another two-part version that's suitable for smaller printers like the Prusa MK3. Printing these parts...

I'm running a CR-10S with a Titan Aero and Volcano heater block, and my final configuration consisted of the following parts. * [Titan Aero CR-10 Mount by CNC Kitchen](https://www.thingiverse.com/thing:2756792) * [Titan Aero CR-10 Volcano Fan Shroud...

Created a Wyze Camera mount for my Creality CR-10S Pro printer. I give props to Monica Mitchel (https://www.thingiverse.com/justmonica/designs) for this design on the CR-10 (https://www.thingiverse.com/thing:3934208) as it gave me the idea for it! I...

The solution addresses a common issue affecting CR-10S and upgraded CR-10 models: when the Z axis moves, the X beam's downward motion causes the right carriage lower edge to brush against the second motor support slightly before the left carriage...

I created a Wyze Camera mount for my Creality CR-10S Pro printer. I give credit where credit is due, Monica Mitchel's design on the CR-10 (https://www.thingiverse.com/thing:3934208) gave me the idea to make it. I redesigned it in Solidworks and...

Found persuadu's Dial mount, but it's specifically designed for a CR-10, not a CR-10S Pro. So I decided to make one that fits over the front of the extruder myself. WARNING: The extruder fan is partially covered by this mount. Be cautious when...

Please note that this design can be challenging to print on a stock CR-10 or CR-10s without proper calibration and assembly. I recommend printing at high resolution, such as 60 microns for PLA, for tolerance and cleanliness reasons. However,...

-Print off this very cleverly designed mount (Thanks for sharing b03tz!): https://www.thingiverse.com/thing:2843893/files -12V Power Supply: https://www.amazon.com/gp/product/B076PMMH3B/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 -LED Strip...

I'm running a CR-10S with a Titan Aero and Volcano heater block and my final configuration consisted of the following parts. Titan Aero CR-10 Mount by CNC Kitchen Titan Aero CR-10 Volcano Fan Shroud by CNC Kitchen Volcano Z Endstop Spacer by CNC...