cr 10s filament sensor upgrade 3d models

1) Filament guide so that the filament does not rub at the entrance of the extruder 2) Designed to avoid blows in the unwinding of the coil (thus better fluidity) How it works: https://youtu.be/2AkbqLxv-2s It is a shock absorber and filament guide...

... the software and make modifications. (Cobnut3D model) Appreciation is due! Now featuring a solid base that positions under the filament runout detector, with an added bowden tube section for effortless filament feeding. ... Working flawlessly.

I made this because I found that certain types of filament would get enough slack in them during a print that they would slip off of the roller and I wanted a loop to keep the filament aligned. The mount and bearing sleeve are un-modified from...

The mount and bearing sleeve remain unmodified from sandeezy's files, included just for clarity.\r\n\r\nI glued the bearing cover/retaining loop onto the mount using the stubby post and the back edge of the loop, being careful not to block the...

so to avoid this future headache, I thought I would add a few guides to keep the filament where it was supposed to stay (even when retracting) so it would stay on the guide. I used SketchUP to modify the file and export it (so of course there are...

... $10-$15. The other weight ratings come in different sizes, so they might not fit. However, this specific 2KG setup can handle readings above its rating and even supports up to 1KG of filament plus the spool, holder, and housing without any issues.

wanted to use 2 bearings in the event i use a different filament holder. so it directs from the top and the bottom. uses 2x 625zz bearings (same as the ones used on v wheels, so if you printer came with an extra wheel you can use both of the...

Remixed to remove the text logo/name from the original. Print Settings Rafts: No Supports: NoResolution: 200 Infill: 20 Filament: PolyMaker PLA Category: 3D Printer Parts

Hi, This is actually a remix of: https://www.thingiverse.com/thing:2822322 by JohnFlimsey (remix section was not working) This is for going on a Sovol Svo1 with a BMG extruder upgrade. Works best with white PTFE tubes. You will need M3 screws. The...

Wehn homing the print head sometimes the filament curles up at the right side of the filament sensor. When you start a new print it can happen that the filamnet gets stuck on the connector of the filament sensor. Then the printer will pull on the...

xxFRESHxx's relocation plate and filament sensor is undoubtedly the best solution among all mods attempting to resolve the CR-10S filament-sensor-that-always-gets-loose issue. Every other mod I've tried shared the same flaw as the original: over...

Filament Sensor Guide for the Creality CR-10 V3 at original position. 4 Pulleys with Ball Bearings Type 608ZZ. Installation with original screws. ...

... the filament spool above the printer. ... In order to maintain a straight-through filament path and keep the filament sensor functionality I designed a sliding bracket and filament sensor cover to enable me to mount the sensor on the top cross bar.

... filament sensor broke. ...Changed my printer to an all metal gear feed and I wanted my filament sensor to be active again. A modification for CR-6 SE Filament Sensor made by Icelandian. ... Original design: https://www.thingiverse.com/thing:4623671

Human Utilizes Basic Filament Switch/Sensor (Stock Sensor If Purchased CR-10 with Sensor). Viewfinder Allows for Visibility of Filament When Threading a New One. Simplifies Removal of Old Filament from Extruder When It Exhausts. ... For Those Slicing...

This is a mount for the filament sensor(s) of the CR-X. The filament end-sensor is fixed to the The filament end-sensor mount with a M5 screw (you could use the Knurling Nut & Bolt included). The filament end-sensor mount is fixed to the frame with...

This is a mounting system for one or more filament sensors used in the CR-X. ...The filament end-sensor is attached to its dedicated mount via an M5 screw, and this mount can be secured to the machine's frame using the same two M5 screws that hold the...

A Mount for the CR-10S Filament Sensor Intended to Be Used with QuadBert's 2020 Rollers. The sensor box is designed to work seamlessly with one of my integrated relocation mounts, and I've successfully tested it on that platform. The 2020 mount is...

It will also come with a filament guide and unload filament protection (since if you will mount the tube directly at the outlet of the runout sensor the filament will be pushed back through the sensor wich may cause some damage to the micro switch...

Use this insert to avoid unwanted pause of CR-10 V3 due to the missed detection of filament. Printing: No special requirement. Installation: Remove the four screws on the filament sensor. Insert the printed part into the lever of the switch. ... ...

I bought a CR-10 Smart and it didn't come with a guide between the extruder motor and the filament runout sensor, so I figured I ought to make one. Has a little window cutout to see that there's filament in there; it doesn't affect feeding. ... This...

I aimed to create a CR-10 filament sensor that seamlessly integrates with my BMG extruder. To achieve optimal performance, I made some minor modifications to the housing for improved switch functionality. You can utilize the original screws from the...

I wanted a CR-10 filament sensor that can be fitted on my BMG extruder. I little bit modified the housing for a better work of the switch inside. You can use the screws of the original Creality housing. ...You only need a M6 nut to screw the Creality M6...

Upgraded filament runout switch for Creality CR-10 features an entire assembly made from aluminum, except the stainless steel tube through which the filament passes and the clear cover printed out of clear PLA. Prototypes were printed to test fit and...

Small riser to rise the filament sensor of a Creality CR-6 SE (probably fits a Max as well). Ha a clamp to fit the electrical connection to the extruder a bit better than the standard clamp as well. The extruder installed is a CR-10 style dual gear...

This is a Filament guide for the CR-V3 which goes on top of the filament sensor. It helps aligning the filament into the sensor, as the sensor has sharp corners where the filament can scratch and create particles. Would recommend using PETG as...

This is a Filament guide for the CR-V3 which goes on top of the filament sensor. It helps aligning the filament into the sensor, as the sensor has sharp corners where the filament can scratch and create particles. Would recommend using PETG as there...

I rewired the filament sensor for the CR-10 3D printer from scratch and bolstered its foundation with a sturdy C-clamp, ensuring it stays firmly in place. This design adjustment prevents the sensor from shifting around and coming loose during...

It completely replaces the included filament sensor. Simply remove the factory installed sensor, extract the internals and move them into this new housing, and reinstall onto printer. The hole in the top is to insert a clear 5mm LED head (just snip...

I required a way to lift the sensor to the BMG Extruder on the CR-6 SE using the filament sensor from https://www.thingiverse.com/thing:4635094. I no longer had the original casing. This was my first ever own 3d print design, so there might be...