cr 10s bed leveling 3d models

Saw a video were someone used this block instead of the piece of acrylic they send you to level his x-axis. Couldn't find the STL anywhere so i made one. ...Can print two, one for each side, makes it a little easier

I designed this 3D model so I could release the binder clips and utilize more of the print bed. I did leave one clip on the back, near the heated bed wiring. ...I've had positive results printing these horizontally with some small supports, but they...

The CR-10s comes with a glass bed held down by metal paper clips, which don't exactly inspire confidence in their durability. I decided to replace these flimsy clips with sturdier plastic ones that would provide a more secure hold. However, my search...

... https://www.thingiverse.com/thing:2782177. ...Semi-Leveling is designed specifically for CR-10 and CR-10S printers using Marlin software. ...I've included an option that prompts you to press a button when leveling one side of the printer is complete.

A guide to help remember the direction of the bed leveling knobs on the Cr-10

This is an inward bed bracket. ... Fits the CR-10S bed size 310x310, if using hypercube inner dimensions for 255x255 2020 extrusions Also fits the CR-10S m4 bigger nut. ... PRINTS ON SIDE WITHOUT SUPPORTS.

A precision tool designed specifically to fine-tune the bed leveling on popular CR10 series 3D printers.

The Leveling File for the CR10S4 Bed Leveling Process is a basic document designed to assist users in adjusting their printer's bed to achieve precise and consistent printing results. ...It takes approximately forty-five minutes to finish, allowing...

... the line separation. After printing, adjust your bed and print again. Repeat this process until all squares appear almost identical. Perhaps you'll need to rotate it 90° since I created it at an incorrect level. ...Sorry, that's my First Attempt.

This bed calibration test has been tailored for the Creality CR-10S PRO, which measures 300 by 300 millimeters in size.

A convenient and robust upgrade for earlier Creality CR-10S models lacking a rear bed/heater cable support, providing a secure solution to prevent damage or tangling.

I consistently forget which way to twist the thumbscrews to fine-tune my bed's position, so I designed a compact reminder that I can easily refer to whenever necessary.

2) manually level with a piece of paper on all 4 corners, then auto-level (if you have a CRTouch/BLTouch) and save to eeprom. 3) use the attached .STL file (super quick, super low filament usage) to run a test print and adjust the corners as...

2) manually level with a piece of paper on all 4 corners, then auto-level (if you have a CRTouch/BLTouch) and save to eeprom. 3) use the attached .STL file (super quick, super low filament usage) to run a test print and adjust the corners as...

This bed calibration test has been adapted for the Creality CR-10S PRO, whose dimensions are 300 x 300 mm. ... Este test de calibración de cama ha sido adaptado para la Creality CR-10S PRO, cuyas medidas son 300 x 300 x 1 mm.

This versatile cable strain relief and bed restraint is designed specifically for the ** CR-10s 4 **, but its compatibility extends to other CR-10 printers as well. It seamlessly integrates with stock hardware. The modification features a press-fit...

This design was made to retrofit onto the stock hot bed of a Creality Cr-10S Pro. I made (as pictured) a lot of newbie 3D-printing mistakes that ruined this bed, so I decided to by a new Wham Bam Flexible Build System bed to replace it. After the new...

... mini-camera mounting system. ...I created it for capturing time-lapse footage with my GoPro on a Creality CR-10S Pro V2. The 65mm gap fits snugly onto the stock bed. ...To secure the camera, I use a strong double-sided tape to attach it to the mount.

I designed a 90-degree strain relief for my Creality CR-10s Pro bed to save desk space. This way, the printer can fit comfortably without hanging too far off the front edge. Simply lay it flat on the build surface and print it with no support needed....

Made to fit perfectly under the bed of a CR-10S, this setup is tailored for a stock Mosfet or a TH3D high-amp 12V/24V Mosfet Heated Bed or Hotend. I incorporated a Noctua 40x20 fan for enhanced cooling, but the stock case fan will also work...

90 degree strain relief for Creality CR-10s Pro bed. I created this to save a little space so the printer can fit on my desk without hanging to far off the front. Lay flat on build surface and can be printer with no support. ...I used PETG but it...

Made to fit snugly under the CR-10S bed, it's designed for a standard Mosfet or a TH3D high amp Mosfet. A Noctua 40x20 fan has been added, but the stock case fan should also work fine. bottom_stock_mosfet_v0.0.6 is tailored for the stock Mosfet,...

This design was crafted to seamlessly integrate with the stock hotbed of a Creality Cr-10S Pro. After succumbing to numerous rookie mistakes that rendered my original bed unusable, I opted for a brand new Wham Bam Flexible Build System bed as a...

CR-10S Pro Heater bed cable strain relief. Along with normal printing I have run some torture tests to check for layer shift or excessive friction. I have had no issues. As a result of not having to drag the cable from the case there is in my opinion...

CR-10S Pro Heater Bed Cable Strain Relief. In addition to standard printing, I've conducted rigorous torture tests to verify that it resists layer shift and excessive friction. Fortunately, no issues have arisen. By eliminating the need to drag the...

CR-10S Pro Heater Bed Cable Strain Relief. I've run some grueling tests alongside standard printing to scrutinize for layer shifts or excessive friction, and I'm pleased to report that I've encountered no issues whatsoever. As a result of not...

A buddy of mine owns a CR-10S and shared with me that his glass was a sturdy 4.5mm thick, giving my own 3mm glass a run for its money. To make up for the extra thickness, I added an additional 1.5mm to the height of my print. My friend confirmed it...

I designed these spacers for my CR-10S that attach to the side rails at the rear and serve two critical functions. Firstly, they keep the printer away from the wall, preventing the clip's handles from hitting the wall when extended rearward, which...

... screws to fit through (sized to 4.5mm in the .STL). These are specifically designed for users with automatic bed leveling. If you don't have this feature, it's still recommended to use the spring system to fine-tune your bed leveling for each print.

CR10s PRO (V2) -Cable touching bed adjustment wheel fix -Nicer appearance -No need to disassemble anything! Would recommend supports only for "Cablemount". ... Credits for cable chain link and its cover: https://www.thingiverse.com/thing:2920060