cr 10 z axis 3d models

... side of the setup, and paired it with another damper. This configuration has proven to be quiet and reliable, and everything is now functioning smoothly. It's worth noting that the CR-10 S supports are not identical to those found on the CR-10 S5.

This is a custom build combining a Raspberry Pi Zero W with a camera mount and an X-axis arm for the Creality CR-10 3D printer. ... Original remixed items are: https://www.thingiverse.com/thing:2230707 https://www.thingiverse.com/thing:2772167

... of the part position a hole for ziptie Other parts are unchanged, download them from the original thing. Source code here (OpenSCAD): https://github.com/spegelius/3DModels/tree/master/CR-10_S5_Y-Axis_Drag-Cable_remix Category: 3D Printer Parts

Adjustable Z-endstop bracket for CR-10(S), I needed one because I lost the old stock one and I wanted it to be height adjustable.

A DIY solution to upgrade the CR-10S X Axis cover using a RAM mount compatible 1-inch ball.

I created this component to elevate the Y axis cable of my CR-10 S5 above the frame, preventing premature wear. This design is engineered to snap securely into the aluminum side rail and lock in place with ease. Use the two round knobs to align it...

I created these custom Cura start and end gcode to assist with the well-known Z-axis alignment issues on the Creality 3D printer Cr-10 v2. These cutouts are designed to avoid the sensors and wiring. This process has been incredibly helpful for me by...

I've created a new X-axis pulley cover for the CR-10 and Ender 2 that's uniquely designed to work seamlessly with either four posts or just two. Unlike other covers available, this one is specifically tailored to accommodate both configurations. To...

I made a new X axis pulley cover for the CR-10 and Ender 2, others only work with the 4 posts, and I have installed dampers, this works with either the 4 posts or just 2. print simply on end (edge with half moon cut out down) with no supports. ... If...

If You Notice The CR-10 Y-Axis Extrusion Is Longer Than Side Supports, This Should Eventually Allow Us To Make A CR-10 Clone Without Any Cuts, Just Using All 500 Mm Extrusions. In Addition To Adding A Top Piece To Screw Into The Y-Axis Extrusion And...

Installing an additional Z-axis leadscrew on a CR-10 printer requires careful planning and execution to maintain optimal performance. To begin, locate the existing Z-axis assembly, typically situated near the print bed. Identify the mounting points...

... material from the aluminum profile. See the picture with the slot. I had to make the slot both wider and deeper. Source code here (OpenSCAD): https://github.com/spegelius/3DModels/tree/master/CR-10_S5_Y_Axis_motor_bracket Category: 3D Printer Parts

... apart and remove some material from the aluminum profile. See the picture with the slot. I had to make the slot both wider and deeper. Source code here (OpenSCAD): https://github.com/spegelius/3DModels/tree/master/CR-10_S5_Y_Axis_motor_bracket

This part is to replace the original in case of breakage. ... This smaples was printed on Creality CR-10 Smart

Linear rail bracket set I designed for the CR-10 v3. You will lose about 30mm of y-axis on print bed. I pared this down as far as I could without compromising support and integrity. Without the loss the left carriage/bracket will hit the stepper...

Y axis belt tensioner for Creality Cr-10 S4 & S5 only. 3 main piece all self locking, sturdy and hand adjustable. Reuses standard parts, No bolts to buy. This unit greatly reduces shock, jerking and noise of printer especially at high speeds and acts...

This is an X-Axis camera mount for the Creality CR-10 and Alfawise U20 printer, which attaches either a web or action camera to the X-Axis, allowing it to follow the movement of the printer. This provides interesting timelapse views that can be...

Move Z-Axis up about 25 to mount and then move Z-Axis back down until it touches so you can zero it out. Then, move the Y-Axis to desired points to check for level. Move mount along the X-Axis and repeat for the bed where you would like to check for...

It has been thoroughly tested on Ender 3, but it should also fit Ender 2 and CR-10 with equal ease, as well as any other printer that features the same x-axis carriage. To get started, you'll need a 70x29mm circuit board with approximately 1.5mm in...

This Y Axis Limit Switch Mounting Bracket for the Creality CR-10 S5 is uniquely designed to overcome two significant shortcomings of the OEM bracket provided with the printer. The OEM bracket falls short in its inability to adjust far enough back,...

Remix from Z Sync Tensioner for 852mm belt for my CR-10 V3,i made it longer for my need,so I can set different belts if i want. ...:) Original file: https://www.thingiverse.com/thing:3988905

I've been using this fantastic X-Axis drag chain end from pgraff (https://www.thingiverse.com/thing:2850432).\r\n\r\nTo get my Petsfang Bullseye (https://www.thingiverse.com/thing:2759439) to fit perfectly on my CR-10, I needed to make some...

I designed this switch box around the cr-10 stock Z-axis end stop switch to work seamlessly with Octoprint. Originally removed from my cr-10 to install the ABL auto leveling sensor, it's now being repurposed as a filament run-out switch. The T-like...

changed : - size - removed cr-10 litter to print it more easily remix from Mars1307 https://www.thingiverse.com/thing:2501854 thanks to him

Modifications have been made to accommodate the [_Mk6__-_CR-10_-_GT2_-_X_Tensioner_-_Screw.stl file, sourced from the website https://www.thingiverse.com/thing:2854971.

... to detail. Begin by aligning the rail guides of the MFN12 with the corresponding slots on the CR-10 frame. ...Securely fasten the mount using the provided screws, making sure they are tightened evenly to avoid any potential instability issues.

The large bed of my CR-10 S5 used to hit the mount of the Y-Axis idler on the front of the lower frame so I could not use the full extent of my printer therefore I designed a similar mount for the idler, but with a lower profile and also capable to...

To eliminate the nuisance of hanging and rubbing cables on your CR-10 printer's back frame, install our Drag Chain Assembly. ...This innovative solution requires minimal hardware: * 2x T-bolt hammer slot nuts and bolts to connect securely to the frame...

If you have a CR-10 Smart Pro you know the hotend cooling fan is loud.  There's a 40mm fan adapter out there for the Sprite hotend but it interferes with the X Axis cover.  Well, this keeps everything working and even adjust the alignment...

This is a custom faceplate for the CR-10 x-axis cable chain by junaling, engineered to fit the following:\r\nBLtouch 3 pin and 2 pin JST connectors\r\nCooling fan 2 pin JST connector\r\nHeatsink fan 2 pin JST connector\r\nThermistor 2 pin JST...