cr 10 z axis 3d models

Simple and affordable to construct, a Z-axis frame brace for the Creality CR-10 features built-in fine adjustment, allowing precise setting of the geometry of the z-axis frame to exactly 90 degrees relative to the base frame on both sides. This setup...

Here is a simple Z axis brace for the CR-10 I modelled in Fusion 360. It mounts behind the Z axis extrusion on the right side, out of the way. I used 1/2 dia aluminum rod drilled and tapped for 1/4-20 in each end but any stiff material could be...

Here is a simple Z axis brace for the CR-10 I modelled in Fusion 360. It mounts behind the Z axis extrusion on the right side, out of the way. I used 1/2 inch diameter aluminum rod drilled and tapped for 1/4-20 in each end but any stiff material...

Add this Z-Axis Offset to free up space for a 4 mm thick sheet of glass on the bed.

This is a Z-axis gusset I created to boost rigidity and minimize vibration. It's installed on the rear of the right side Z upright. Take a look and share any suggestions or improvements you might have. ... Hardware (4) M3 x 8 socket head cap screws (4)...

For those of you that have installed the dual Z upgrade on your CR-10 I have reworked the brace file to mount to the side of the printer. The rod length is 20 1/2 inches. You will lose about 1 1/2 inches of Z height with this setup. ...Please refer to...

For those who have installed the dual Z upgrade on their CR-10, I've revised the brace file to securely attach it to the side of the printer. The rod length measures exactly 20.5 inches. With this setup, you'll experience a loss of approximately 1.5...

After upgrading my CR-10 with dual-z, I discovered that the two factory-supplied lead screw top mounts varied in size by several millimeters. These replacement mounts keep the lead screw at the same distance as the stepper motor at the bottom,...

Designers unveil sleek new Z-axis knob concept. The innovative design prioritizes functionality and user experience. Aesthetically pleasing lines and clean edges create a visually appealing interface. ...Intuitive tactile feedback ensures effortless...

As I examine my Z-Axis Stepper, I notice that it's not precisely aligned with the threaded rod. This misalignment puts excessive stress and force on the Z-Axis Coupler. To correct this issue, I created a simple 1mm spacer that fits between the stock...

This upgraded component is specifically tailored to enhance the capabilities of the Creality CR-10 3D FDM Printer. The bar collectors in question are engineered to accommodate tubes with a diameter of either 10 millimeters or 19-20 millimeters. ...If...

I installed an e3dv6 clone with Volcano on my CR-10, and while things worked out okay, I had to adjust maybe 3 or 4 threads to get my bed just right. At some point (2-1) the bed started flapping around, so I didn't feel comfortable being at the edge....

The only way I was able to successfully print perfect threads on the wheel was by using specific print settings: printing the wheel in a flat position with the z-axis location boss facing upwards, and printing the knob upright with pins pointing...

it need 2 10mm X 50mm bar and 16 M3 bolt and nut

This two-piece part supplants and amplifies the acrylic stock cover on the Creality CR-10's Z-axis lead screw; It allows you to manually control the hot end up and down when steppers are disabled, a feature I have found extremely useful at times. For...

CR-10 Mini Z-Axis Brace Brackets, Designed for Maximum Versatility These brackets will probably fit other CR-10/Ender series printers with some threaded rod length adjustments. The upper bracket is long enough to clear the print head assembly and a...

For this makeover, I utilized the following components: 1pc Machifit 500mm Lead Screw with an 8mm thread and a 2mm pitch lead screw featuring a copper nut -> https://goo.gl/cKueAs 1pc 608ZZ bearing - OD22xID8xH7 -> https://goo.gl/ePWxcj 1pc Flexible...

Creality Ender 3 users please read the last update below #ZKNOB This two piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw; It lets you manually control the hot end up and down (when steppers are...

**#ZKNOB** This two-piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw. It lets you manually control the hot end up and down when steppers are disabled, which I have found to be very handy at times. For...

This thing is a mount I designed for implementing linear rails on the Z axis of a Creality CR-10 printer. You will need to print two, please mirror the second one. ... Each mount requires 2 x M5 bolts of 40 mm and 4 x M3 bolts of 30 mm

#ZKNOB This two-piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw. It lets you manually control the hot end up and down when steppers are disabled. I have found this to be very handy at times, such as...

A new Z-axis endcap for the CR-10 is now available, unlocking its full height potential. This upgrade will give you a maximum build volume of 420 millimeters or an additional centimeter with ease. The new endcap features a snap-fit design that easily...

This is a custom designed cover specifically made to fit over the motor switch of your trusty CR-10 3D printer's Z-axis. The cover protects the electrical connections and prevents accidental damage or tampering with the delicate components inside.

Here is a bracket designed to mount a vibration damper on the bottom of the Z-Axis Stepper Motor for the Creality Cr-10. This bracket replaces two of the bolts at the bottom of the stepper motor with longer M3 x 30mm bolts, which can be easily found...

It enables users to assemble a linear rail on the right z-axis pillar, replacing the stock plastic wheels with more reliable components. This modification should significantly improve stability and accuracy. ... To complete this upgrade, you will need...

Fit the new block to the printer with the screws on the top and move the Z axis all the way to the top. Tighten the screws. This will hold the bearing in the correct Y direction. Home the axis and then remove the new bearing and refit with the screws...

The knob design created by baschz does not fit my leadscrew, and the Z-axis bearing on his machine is different from mine as well. I have redesigned it to create a completely new bearing that will fit all printers. This new bearing block utilizes...

Printer: Creality CR-10 Rafts: No Supports: No Resolution: 0.2 mm Infill: 30% Notes: Print the knob upside down. No supports needed. Pictured parts are printed in Das Filament PLA at 190°C/50°C on the Creality CR-10. You can probably print it...

I added height to this knob to clear the top of the frame braces I just printed and installed on my CR-10 https://www.thingiverse.com/thing:2123233

New: Combo YZ Bracket for Efficient Cable Management on CR-10 Printers When utilizing this combo along with the design from Thingiverse (https://www.thingiverse.com/thing:2708420), a drag chain assembly is required to manage cabling from the X...