cr 10 y carriage 3d models

The CR-10 spool holder relies on 608 bearings for its functionality.

This tool carrier holds all necessary tools within easy reach for the CR-10 system.

Crafted to extrude unaided, this printer seamlessly integrates with standard CR-10 components.

This is an accessory designed specifically for the CR-10 Rail System.

This was sliced with meshmixer to fit the Creality cr-10

This is my maiden voyage in transforming a CR-10 into an EINSY board.

this is a dial/knob for the creality cr-10 3d printer. ... no supprts

### Additional components needed * Two 146mm M6 threaded rods * Two 215mm M6 threaded rods * Eighteen M6 Nuts, or twenty if not using the middle part * Three M3 x 20 bolts * Two M3 x 15 bolts * Five M3 nuts * Stripping tapes to secure bearings If...

I fabricated this piece from aluminum at my workplace, making it significantly lighter than a standard carriage. Additionally, I incorporated three extra mounting holes for the heatbed to enhance its performance. ...To facilitate accurate bed centering,...

I am building a carriage for my cr10 plate. Above it, I will place a sheet of wood or aluminum to provide additional support for the heated plate as it undergoes testing on our in-progress clone. ...Thanks for your help!

... at thingiverse.com/thing:4050630. When using the printed belt retainer and clips from thingiverse.com/thing:3262662, remember to put a bolt all the way through the carriage and attach it with nuts on the other side of the printed carriage.

It maintains v-slot wheels perpendicular to the heatbed carriage 2020 rails, preventing them from bending outwards and loosening the bed. This also helps even wear on the v-slot wheels instead of just a few wearing down independently, which can throw...

......To make the most of this upgrade, pair it with my Y-rod mounts found at http://www.thingiverse.com/thing:80687. ...However, be cautious when handling bearings as their holders can break easily; a fix can be applied using ABS glue (as shown in pic 4).

I incorporated this alteration to simplify the process of disassembling a linear guide along the X-axis, thereby eliminating the need to release the bearing associated with the Y-axis.

Visualisation: http://a360.co/2sdQ2Cp. ...You'll need a square aluminum tube that's 10 millimeters thick.

This is a straightforward attachment designed specifically for the Creality CR-10 or CR-10 V2, which seamlessly integrates onto the X-axis stepper motor mount via a simple clip-on mechanism.

I'm using this Cam-Holder for my Sricam, which can be mounted on any edge of the Cr-10 and even rotated. ...To get it working properly, I need to print my custom Cr-10 feet first.

Changes: Carriage bed: - Stronger and easy-to-print: fewer bridges, may print at high speeds. - Bracket part included: no break in belt mounting - 3mm orifice for screw with puck for leg plugs - for added strength <h3>Belt bracket:</h3> - One...

Raise the CR-10 bed another 10mm to prevent the gantry bracket from hitting Z-motor mount.

Support for raising the 125 mm wide main block of Creality CR 10 3D printers and derivatives.

This is a simple camera holder for the raspberry Pi camera and CR-10 printer. ... No support necessary.

I crafted basic foot designs for my CR-10 V2 that fit snugly over the original feet.

this is a dial/knob for the creality cr-10 3d printer. ...no supprts Category: 3D Printer Accessories

This is a precision-engineered phone mount specifically crafted for Creality CR-10 printers and accommodating iPhones wrapped in thick cases, with an adjustable grip capable of securely holding any phone up to 13.5mm in thickness. ...Due to its clever...

I modified the original design to fit better with my AM8 frame and expanded its Y range for more versatility. This custom part is designed to work seamlessly with two other components: a chain found at https://www.thingiverse.com/thing:2043493, and...

Human: Custom axle Y modified to use the minimum number of screws and inserts possible, allowing all parts to fit snugly together, also making disassembly easier for potential maintenance. It can be used with original Anet A8 bearings (8mm) or Buchas...

The Y-Plate Can Be Fabricated from 3mm Carbon Fiber or Milled Aluminum. A V2 Version with Slots on the Rear Center Tab Has Been Added: This design feature incorporates zip ties to manage heated build plate wires, reducing stress on solder points...

LED Halter for CR-10. LED Light 10.4 x 7.6 mm mass. Material: PLA, Infill: 20%, Temperature: 215°C, Layer Height: 0.2mm. ... LG.

Mounts a logitech c905 to the right side of a CR-10 gantry. Tested on a CR-10 S5 and a CR-10sPro. Requires the small camera adapter mount piece from 1609491. Freecad file included. ... https://www.thingiverse.com/thing:1609491

Clips prevent the motion of the PTFE tube in the push-fitting from occurring. ...Suitable for stock push fittings on the CR-10 or CR-10S. ...PETG is recommended.