cr 10 v3 upgrades 3d models

MDG CR-10 V3 UPGRADE PROJECT Official Site: **[MAKERS DEVELOPMENT GROUP](https://www.makersdevelopmentgroup.com)** MDG CR-10 V3 Project Link: **[MDG CR-10 V3 UPGRADE PROJECT](https://www.makersdevelopmentgroup.com/cr-10upgradeproject)**

... part thinner so it properly fits over the hotend. ...There is some clearance, but just enough Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No Supports: Yes Resolution: 200 Infill: 20 Filament: Jayo PLA Black Category: 3D Printer Parts

I am no designer, engineer or expert designing parts for 3d printers, I just adjusted the original parts design by DaVinci2000 to make them work with the Creality CR-10 V3 using the stock parts it comes with. If you find this useful you can always...

SCALE to 1% (sorry about that) I have made the clamping part thinner so it properly fits over the hotend. ... There is some clearance, but just enough

Upgrade for CR-10 with BTT TFT35 new 3D printer for small money.

Combined and designed this setup from the best ideas and designs I could find (in my humble opinion of course)Features:Single piece backplate.No loss in build volume.Nozzle in original position.Cable routing thru backplate for nice cable...

... for improved airflow is a breeze, thanks to easily replaceable parts. ...To get started, check out these innovative designs and installation guides at https://fdproj.wordpress.com/2018/01/22/cr-10-silent-new-fans-vibration-dampers-and-design-upgrades/.

... v2 y listo A disfrutar. Pick up cable from the extruder of the cr-10 v3. I couldn't find anything and designed this piece. It is very fast and effective. ...With two screws it is attached to the extruder hole of the v2 and that's it To enjoy.

I was always annoyed with the control box being off to the side of my new Creality CR-10 V3 printer, so I decided to do something about it. The control box now sits underneath the printer and really cleaned up my workspace a bunch by giving the...

UPGRADE SPOOL FOR ENDER CR 10 V3 ENJOY

This is just the E3D Direct Drive extruder cover of the Creality CR-10 V3. ...The original part is a transparent injection molded piece, which breaks easily if you tighten the screws a bit too much.

Cadena para CR-10 V3, así se evita que se arrastren los cables y choquen contra tus impresiones, se necesita: - 4 tornillos m3x12mm - 4 tuercas m3 - 2 Bridas o cinchos

On my CR-10 V3, if I used the CR Touch as-is it would cause my nozzle to crash into the print-bed. This spacer adds 4mm headroom between the probe and nozzle. Works with the stock screws that come with the CR Touch. I printed with 50% infill,...

The CR-10 V3 Fan Base uses two 120mm fans. I attempted to connect the fans to the 12v fan connection port in the power supply, but discovered it is temp controlled (off until it heats up). I wanted the fans blowing air up into the control all...

there arent many people designing spool holders for the cr-10 v3 with direct drive without modifying the sensor so i just quickly came up with this. added more perimeters along the base and im glad i did because the t nut holes weren't big enough. ...im...

Here I bring you a small solution for that Creality CR-10 V3 filament sensor that produces too much friction. Having it at the top can cause a possible breakage underneath the sensor, the printer would still work without detecting it. It connects...

CR-10 v3 standalone (updated 16.06.2022) two versions of front LCD mountt, one for TFT35 one for original LCD You will need extra screws: M5x30 4 pcs for legs M3 x 30 5pcs for motherboard cover M4 x 30 5pcs for mother board box and power supply...

CR-10 v3 standalone (updated 16.06.2021) two versions of front LCD mountt, one for TFT35 one for original LCD You will need extra screws: M5x30 4 pcs for legs M3 x 30 5pcs for motherboard cover M4 x 30 5pcs for mother board box and power supply...

The CR-10 V3 sensor bracket is, to say the least, useless because the angle it makes with the spool and the extruder is generating a lot of friction. So, the basic idea was to put the spool above the sensor, but it is way easier to put the sensor...

Designed this to add to the back of the filament runout sensor mounted on top of the latest CR-10 V3 models. Uses a pair of 608ZZ bearings. I printed the guide wheels out of TPU however you could use any material. I made it so the filament feeding...

The CR-10 V3 sensor bracket is, to say the least, useless because the angle it makes with the spool and the extruder is generating a lot of friction. So, the basic idea was to put the spool above the sensor, but it is way easier to put the...

Please visit our build page for more details [MDG CR-10 V3 - Official Upgrade Mod Project ](https://www.makersdevelopmentgroup.com/cr-10upgradeproject) Requires (4) [M5 X 50mm Socket Head Cap Screws](https://amzn.to/37hNshW) Recommended 3D Printer...

... ...Perfect for mounting linear rails on the Y-axis of a CR-10. Please visit our build page for more details MDG CR-10 V3 - Official Upgrade Mod Project Requires (4) M5 X 50mm Socket Head Cap Screws Recommended 3D Printer Filament Material PETG

... more center mounted. print with brim, tree supports .2mm line v1.2 beefed up roller pins Print Settings Printer Brand: Creality Printer: CR-10 Rafts: Doesn't Matter Supports: Yes Resolution: 200 Infill: 20% Filament: Sunlu PETG Category: 3D Printing

I also changed the angle of the filament sensor to allow to be more center mounted. print with brim, tree supports .2mm line v1.2 beefed up roller pins Print Settings Printer Brand: Creality Printer: CR-10 Rafts: Doesn't Matter Supports: Yes...

there is not much place where this system could be used with V3 and especially to be from the front With this adjustable Endstop which can be moved to 2 sides, which allows you to precisely place the screw above the endstop, unfortunately you will...

Cover for the CR-10 V3 input voltage switch

... move the tension spring screw to the left, while cover 5 narrows and moves the bowden tube fitting to the left. Knob in image is from https://www.myminifactory.com/object/manual-filament-feeder-knob-mod-for-cr-10-and-other-bowden-3d-printers-52492

Updates: 8/8/2022: Added version of BLTouch mount with cable holder rod - - - Здесь представлены изменённые детали из [K3D Printhead for Ender-3/Aquila/CR-10](https://www.thingiverse.com/thing:5172583). Включает в себя: 1) изменённую версию...

This thing helps to cut bowden tube exact lenght 82mm for Creality CR-10 V3 with Titan extruder