cr 10 v3 extruder upgrade 3d models

The filament sensor on the CR-10 V3 is has a mechanical flaw that can cause one of the following to happen: - you can't insert filament through the sensor (jammed) - the sensor indicates no filament when there's filament in there, which can happen...

... for air flow. - On the opposite side close all openings and holes with tape - place two 120mm fan's on the new bottom plate. Put 2x 12V fan's in series to use original 24V - Screw all togeher and hear the silence It's designed to print on CR-10 v3

CR-10 V3 have some issue with filament sensor giving too much drag & strain on the filament I designed this mod so i can mount the sensor directly under the filament spool I never had to print things higher than 300mm, but you should note that this...

CR-10 V3 pi mount that clears the support arm and no hardware is required ! I hate when I have to track down nuts and bolts, etc.. This holds my pi cam v 1.3 perfectly and allows me to adjust the lens focus without removing the camera board. You...

Linear rail bracket set I designed for the CR-10 v3. You will lose about 30mm of y-axis on print bed. I pared this down as far as I could without compromising support and integrity. Without the loss the left carriage/bracket will hit the stepper...

With that in mind, I've created a new spool holder that slides into the 2020 v-slot extrusion on the top of my CR-10 v3 printer. \#1 is solved but it simply sliding to clamp the spool in place, and \#2 is solved by having two "rods" instead of only...

This thing allows you to mount a Phaetus Dragonfly BMO to your CR-10 V3 without the bulky stock housing. The fan mount can be used with the stock hot end as well. I wanted to have a mount for the fans that wasn't integrated in to the hot end...

Extruder Knob for the Creality Ender 3 / Ender 3 Pro / CR-10 Remix

Recent adventures necessitated I move from my Robo3D R1+ (an antiquity at this point) to a newer platform - hence the CR-10 V3 (I like direct drive). Having already printing a [cable chain](https://www.thingiverse.com/thing:4725258) to fix an...

Extruder Crank for the Creality CR-10. ...Body Dimensions: Ø 35 mm x 8 mm External Top Dimensions: Ø 8 mm x 7 mm Internal Top Dimensions: Ø 5.2 mm x 12 mm Flat Area: 4.5mm

For the CREALITY CR-10 V3 printer. The original Creality Silicone Dampers are too short for this printer resulting in the print bed being too far away from the nozzle. This spacer fixes the issue, fits perfectly into the Creality damper and moves the...

CR-10 M4NOT COMBATIBLEAny Ender 5 model, Any Ender 3 V3 model======================================================================================================= BILL OF...

This adapter plate offers the possibility to install a BigTreeTech SKR2 mainboard in the electronics housing of the CR-10 V2/V3. The plate is screwed in place of the original mainboard (Creality V2.5.2) with M3 screws (use the existing screws) and...

This is a 120mm fan adapter for the new style CR-10 V3 control boxes with 2mm cooling holes on the sides instead of slots. It snaps securely into place and replaces both the 50mm and the 40mm Creality fans. Please be aware that the power supply...

If you want the longer sides front and back, check out this remix: https://www.thingiverse.com/thing:4864920 Complete system to mount a BIQU H2 to a Crealty CR-10 V2 or V3. Route heater and thermistor wire between mount and plate. Heater wire should...

If you want the longer sides front and back, check out this remix: https://www.thingiverse.com/thing:4864920 Complete system to mount a BIQU H2 to a Crealty CR-10 V2 or V3. Route heater and thermistor wire between mount and plate. Heater wire...

Remix of CallJoe's Creality CR-10 Bed Leveling Indicator V2, modified to fit above the air cooling exhaust for a sleeker design.

This is a set of clamps designed to replace the hinged metal glass clips included with the Creality CR-10 V2/V3. These clamps will hold your glass in place with the added benefit of not obstructing **any** of the print surface. Never worry about...

I think I've got the final version of my plan to relocate the extruder on my CR-10 to feed filament up from below. I combined an extruder body, a relocating bracket, and a drag chain mount, giving me a solid foundation for this upgrade. To increase...

I am no designer, engineer or expert designing parts for 3d printers, I just adjusted the original parts design by DaVinci2000 to make them work with the Creality CR-10 V3 using the stock parts it comes with. If you find this useful you can always...

Place a decorative item atop your CR-10's extruder to inject some whimsy into your 3D printing experience.

CR-10 S4 Direct Drive Extruder Mount Rev. ...01 Watch this video on YouTube: https://youtu.be/drFjboCvHf8

Add a whimsical touch to your CR-10 by placing a creative accessory on top of your extruder!

Designed up this fan duct as I bought the CR10 V3 and the extruder was very frustrating to access when needed. Hot end cooling fan cowl is optional, i thought it looked pretty. ... Please note this is a work in progress, I'm still testing and...

... PETG or ABS, for heat resistance. Sometimes the extruder stepper motor can get hot, and the last thing you want is for your extruder to get soft and melty.The part I remixed was itself a remix, so the licensing on this follows that of the original.

this is a mod made for the cr 10 v2 and 3 as a flat design you can use to cut out and fold for metal and other materials you can get to work https://youtu.be/uubrlFYza9Q video link standoffs for screen and mother board files are also included

This is my first crack at a cable anchor/tie for my CR-10 V2, which is using a direct drive mount and had no convenient place to tie wires. ...I'm definitely still working on this one, but the current revision works rather well.

Design to mount a Voron Afterburner on a CR-10 v3. For BL-Touch mounting, it can be left off, or use the bracket that comes with the kit (or available as [Thing 3940873](https://www.thingiverse.com/thing:3940873)) There's also a cable...

It works with CR-10V3 with direct drive extruder. It also has a tunnel for CRtouch or BLtouch wires. Clip design allows you to install this chain links without removing any wires from the board. You can also remove the bolts on extruder and remove...

Dual Extrusion System Upgrade: Installing a CR-10 Linear Rail Mount Upgrade your 3D printing experience by incorporating a reliable and efficient linear rail mount system designed specifically for dual extrusion setups. This innovative solution is...