cr 10 upgrade 3d models

Creality CR-10 Upgrade Suite. This kit features an upgraded extruder with enhanced ergonomics and functionality alongside an improved bed level adjustment system. New as of January 25th, 2018 is the inclusion of a E3D-V6 hot-end adapter, which...

Check out my brand new upgrade for my printer! I'm really excited to share it with you all and hope you love using it too! Here are the parts you'll need: 1. Rubber legs, M8x1.25 x 40 - these will give your printer some serious stability 2. Washer...

I created this frame because I wanted to gradually move the contents of my CR-10 control box underneath the printer. I'm using 2040 aluminum extrusion. Two pieces were cut for the entire length of the "Y" axis, and two more were cut for the entire...

MDG CR-10 V3 UPGRADE PROJECT Official Site: **[MAKERS DEVELOPMENT GROUP](https://www.makersdevelopmentgroup.com)** MDG CR-10 V3 Project Link: **[MDG CR-10 V3 UPGRADE PROJECT](https://www.makersdevelopmentgroup.com/cr-10upgradeproject)**

This is the collection of remixed and aggregated items for a pro upgrade kit designed specifically for the CR-10. This package should help you resolve most issues with maintaining a clean setup for your CR-10, allowing you to achieve optimal...

The CR-10 Nozzle Cooling Fan Duct Upgrade allows for increased airflow through two substantial ducts, strategically positioned at a plenum beneath the fan. ...This design directs cooling air toward the nozzle's tip, enhancing efficiency while keeping it...

This is my attempt at dual-Z upgrade for CR-10 using a single stepper motor. It uses a 600mm lead screw kit such as this one: ...

The CR-10 hotend performs perfectly, whereas I and several others have encountered numerous issues with the Monoprice factory hotend. No additional hardware is necessary. Simply print the backplate with supports facing upwards, as the faceplate does...

The fan mount is adjusted upward to accommodate larger and more powerful 40mm fans.

This upgrade enhances printers such as CR-7, CR-10, Ender 2 and Ender 3. The PTFE insert is secured by an additional extrusion that seals off the gap in the extruder where TPU normally gets jammed. Adding a rubber to the steel-roll also optimizes...

This is an upgrade for CR-10[s] to mount as you prefer: - 2 x 120mm fans - 1 x 120mm fan and a RaspberryPi - 1 x 120mm fan - Just the RaspberryPi - Nothing, because the base can cool itself alone According to your choice, print only 2 x "CR10 - Base...

There are some alternative solutions for this already but I wanted a simpler design so this Cable Holder (for the upgraded metal extruder for Creality Ender 3/5) simulates the original cable holder on the plastic extruder that comes with the printer....

for the creality_ender3 series 3D printer upgade to ceramic clay 3d printer pneumatic kit part, holder(cradle) more information refer to this link: https://www.aliexpress.com/item/32763502524.html ...

This is my take on an upgraded fan shroud for my CR-10. It fits a 40mm fan and a 50x15mm blower for part cooling. I included a custom fan duct for this mount. BLtouch mount is built in and the offset is 7mm forward and 24mm to the right, or...

I designed a high-performance upgrade for my CR-10's fan shroud, accommodating both a 40mm fan and a powerful 50x15mm blower for optimized part cooling. A custom fan duct is seamlessly integrated into this design. The BLtouch mount is thoughtfully...

... part thinner so it properly fits over the hotend. ...There is some clearance, but just enough Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No Supports: Yes Resolution: 200 Infill: 20 Filament: Jayo PLA Black Category: 3D Printer Parts

This upgrade builds on the Filament Feeder found in edwardchew's CR-10 Spool Holder Top Mount & Upright Filament Guide. Every aspect of the original design is exceptional, except for one thing; the filament feeder itself. Due to excessive friction...

The CR-10 V2 already comes with a super quiet stepper controller, but the stock fan included are extremely loud, so I replaced them all with Noctua fans. Here's what I used: * Noctua NF-A6x25 FLX x2 - one for the PSU and one for the casing *...

... for improved airflow is a breeze, thanks to easily replaceable parts. ...To get started, check out these innovative designs and installation guides at https://fdproj.wordpress.com/2018/01/22/cr-10-silent-new-fans-vibration-dampers-and-design-upgrades/.

Here is a revised version of the original text: This upgrade takes the ["Cr-10 Guide wheel"](https://www.thingiverse.com/thing:2666347) by Gazz001 to the next level, reinforcing screw holes to prevent breakage that I experienced firsthand and adding...

These are some upgrades i designed for my CR-10 S5. With these feet you get about 11 cm of clearance below you printer. It is easier to acces the bedleveling screws. You need 12 M4 x 25 mm screws and 4 squash balls (or any other Ball with a...

I am no designer, engineer or expert designing parts for 3d printers, I just adjusted the original parts design by DaVinci2000 to make them work with the Creality CR-10 V3 using the stock parts it comes with. If you find this useful you can...

SCALE to 1% (sorry about that) I have made the clamping part thinner so it properly fits over the hotend. ... There is some clearance, but just enough

As I fell in love with SanderPuhs's Cr-10 Fang design and printed it for my customized CR-10, I had to acknowledge that one small thing wasn't functioning properly. Sander did an excellent job designing the BLTouch mount, but because of its...

To facilitate this upgrade, I designed some easy-to-mount components that enable you to attach the laser directly to the printing head or use a second bracket mounted on the frame of the CR-10. ... These parts should work seamlessly with the laser I...

Upgrade your CR-10 OEM spool holder for a smoother printing experience. Say goodbye to spools that sit off center, swing erratically and misbehave. This upgrade likely works for many brands as the arm is standard on numerous models. The insert is...

This modification is specifically tailored for CR-10 printers, allowing them to work seamlessly with flexible filaments like TPU by sealing the gap in the extruder with a PTFE insert. This clever solution prevents jams and ensures smooth printing. ... I...

The Hictop CR-10 printer is notoriously loud, and I've lived with it in my room long enough to know its persistent humming can be a real nuisance at night. It was time for an upgrade - one that would hopefully silence the racket once and for all. I...

Automatic mechanical shutdown after print completion for the 3D Creality CR-10 printer is a crucial feature that ensures your machine shuts down safely and efficiently once a print job has been completed. This prevents overheating, unnecessary energy...