cr 10 psu 3d models
296063 3d models found related to cr 10 psu.thingiverse
This is a straightforward bracket designed to secure the CR-10 PSU beneath a desk, thereby freeing up valuable space. To install it, you simply need to use 4 wood screws. For added stability, consider attaching self-adhesive velcro strips to prevent...
thingiverse
I designed a custom spacer/adaptor to fit my Creality CR-10 power supply, allowing me to upgrade from the loud stock 60x10 mm fan to a super silent Noctua 60x25 mm fan. This modification greatly reduces noise coming from the PSU. For maximum...
thingiverse
This is a model of the Power Supply that comes with My Creality CR-10. The Hole Locations are As Accurate as Possible. ... Note: This Model May Be Compatible With Other Makes and Models, Including But Not Limited to.
thingiverse
This remix takes the PSU plate to the next level with reinforced walls that can handle the weight of a power supply unit (PSU) with ease. Built in just 15 minutes using Tinkercad, this design is still in the testing phase. If you download it, please...
thingiverse
... sure they are properly secured to prevent damage or obstruction. Finally, test the system thoroughly to verify that the PSU is functioning correctly under load conditions, paying close attention to temperature readings and overall performance.
thingiverse
Remove the rubber feet on the CR-10 PSU using a supplied allen wrench and attach this bracket with the same screws you just removed. I added slots to account for printer calibration differences. Both prints were fine at 30-35% infill settings. You...
thingiverse
I Created a Custom PSU Mount for My Controller Box, Drilling Holes as Needed and Upgrading the Front Panel for Better Wire Management. ... Updated designs are available in 123 formats, allowing users to tailor their PSU mount to any desired size.
thingiverse
Here's a mount designed specifically for the BTT GTR V1.0 board that seamlessly integrates with the Stock CR10 PSU. ...By creating this custom mount, I aimed to preserve the original appearance of the stock controller enclosure while still accommodating...
thingiverse
- I can actually carry the entire psu just by grabbing the fan :) For those of you who are worried about vibrations: I have mine running and can only tell that it is, when putting my ear right next to it. (So no problem at all!) Please ignore bad...
thingiverse
Fan shroud for the PSU unit on the CR-10 Max. Model is done to minimise the material used, thus the wall is thin. I printed it with 0.6mm nozzle with 0.8mm line width (the wall thickness) and 0.3mm layer height. ... you can use a 0.4mm and push the...
thingiverse
I've created this fantastic PSU air duct to significantly reduce noise (2dB!) and enhance cooling for your PSU. By doing so, the PSU is now drawing in cooler air from outside, rather than sucking in hot air from under the heated bed. Please...
thingiverse
Sink head screws are required.
thingiverse
This bolts onto your PSU cover so that you may add PVC pipes leading to the outside of your enclosure. ensuring your PSU gets cool air and not recirculated hot air. This is if you use an enclosure. ... I added a .DWG file to the download to make...
thingiverse
The CR-10 V2's Meanwell PSU operates at 24 volts, so you'll need a Buck Converter or other solution to provide the necessary 12V for the new fan. I've split the bottom cover into two parts for easier printing and ensured a secure fit when tightened....
thingiverse
It holds the original PSU coming with the CR-10, if you want to convert the classic CR-10 into a boxless version (similar to the Ender 3). The mains voltage section of the PSU is seperated from the output voltages and contains no screws/screwholes. ...
cults3d
... ...It holds the original PSU coming with the CR-10, if you want to convert the classic CR-10 into a boxless version (similar to the Ender 3). The mains voltage section of the PSU is seperated from the output voltages and contains no screws/screwholes.
prusaprinters
It holds the original PSU coming with the CR-10, if you want to convert the classic CR-10 into a boxless version (similar to the Ender 3). The mains voltage section of the PSU is seperated from the output voltages and contains no...
thingiverse
... have to raise the printer to house this mod, see my designs for a foot extension. Also you will have to design a power inlet that fits your needs, I've been sloppy so far, using a cut cable directly to the PSU. Don't be like me. ... Use PETG.
thingiverse
... ...I've added a mount for an SFX power supply to the cover of his "CR-10 Standalone Kit". Note: Untested yet. ... You can use, for example, the following SFX Power Supply: Corsair SF450, Thermaltake Toughpower SFX 450W, or Creality CR-10S 3D-Printer.
thingiverse
I made this to keep my control box out of sight. Print one and position it inside the control box. On top of the control box, I secured it with double-sided tape to prevent movement. ... Verify the cable length; you might require an extension kit.
thingiverse
This is my take at a CR-10 All-In-One control box replacement that will fit snugly under the heat bed and allow for a clean sweep behind the control box. This design is tailored specifically to the Raspberry Pi 4B, a high-capacity 60W power supply,...
thingiverse
My Simple Design to mount the Standard 12v PSU (power supply unit) CR-10/CR-10S. without any screw to attached the frame. just slide through the aluminum frame. ...Please Download & enjoy -Arcmal-
thingiverse
This cover enables you to put silent noctua 60x25 FAN.
prusaprinters
This cover enables you to put silent noctua 60x25 FAN. ...Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printer Parts
cults3d
This cover enables you to put silent noctua 60x25 FAN.
cults3d
It has IEC320 input with fuse and switch as well as an outlet for the mains voltage heated bed I switched my CR-10 S5 to. This has been such a huge performance improvement! This comes with a replacement port to let you use a 4 pin connector for 5v...
thingiverse
It has IEC320 input with fuse and switch as well as an outlet for the mains voltage heated bed I switched my CR-10 S5 to. This has been such a huge performance improvement! This comes with a replacement port to let you use a 4 pin connector...
thingiverse
This feature is ideal for crafting components that seamlessly integrate with the CR-10S and CR-10 rail systems.
thingiverse
Installation space lighting for the CR-10 / CR10S. Fastened with two nut blocks and M4 screws each, it provides a secure fit. Two 10cm LED strips are used in conjunction with an affordable LED dimmer to create the desired ambiance. Part three...