cr 10 mods 3d models

This is a straightforward cooling mod for the Creality CR-10 that delivers top-notch print quality. By directing fan airflow directly onto the nozzle tip, it prevents overheating and maintains optimal temperatures. For those seeking exceptional...

This is an easy-to-mount cooling mod for the Creality CR-10, the other CR series, and the Ender 3. This mod redirects fan airflow directly to the tip of the nozzle without being too large or obstructive. If you are looking for the best print...

This is a custom modification of Spotone's ABL mount for the Ender3/CR-10 to accommodate the CR-10 hanging fan mod for MicroSwiss and E3D hotends. The mount is designed specifically for an 18mm proximity sensor. For reference, please visit: ...

Remixed Design with Lower Build Plate. ...I modified the original design to clear the heated bed of my standard CR-10, ensuring a safe and smooth printing experience.

... extra length of the E3D volcano hotend. ...The Spacer fits perfectly, attaching directly to your CR-10 using an existing bolt. To quickly install a Volcano hotend on your CR-10, just follow this easy guide: https://www.youtube.com/watch?v=mdj4UXfna7g

<p>A spacer, that compensates for the additional length of the E3D volcano hotend. ...Mounts directly to your CR-10 with an existing bolt. How to easily install a Volcano hotend on your CR-10: Category: 3D Printer Parts

... the Nozzle. ... You can print either a 3/4 round version or a full-round version of this mod. Mounting this mod is incredibly straightforward - no additional parts are required. ...Simply swap out the original mod with two screws and you're done.

These are the parts I designed to boost stability on my CR-10 S5. Included are brackets that you can 3D print to use as the joints for attaching the extrusions. For the extrusions, I got them from openbuildspartstore.com. To assemble the double...

Thanks to xxricsxx standalone mod my electronic is nicely hidden under the heatbed. I just want to add a cover to prevent filament parts falling down into the electronic parts and decided to use 0.5mm ABS sheet to cover both sides. Size is 14cmx46cm....

I've been developing a fan modification that complements the standard fan perfectly and outperforms its predecessor in terms of efficiency. ...To secure the top screws effectively, I suggest drilling a hole at the top for the first two bolts, however,...

This modification is based on nuggyblake's fan creation, which can be found at https://www.thingiverse.com/thing:2303102/#files. To improve its fit, I've added fillets to the screw holes. ...Additionally, a curved section at the front allows for...

For a donation, please visit https://www.paypal.com/pools/c/81EmSoZNia. https://youtu.be/VjhWu9qpSKg. Today, I've published an update that allows you to replace the teflon wheels with a linear 40 mg mgn driver. The improvements are substantial, and...

My Customized Extruder Cable Mount with Integrated Filament Channel. Updated on October 15, 2017: Increased cable support thickness to enhance structural integrity. ...I've also designed a dedicated slot for PTFE tubing, serving as the filament guide.

My Customized Extruder Cable Support with Integrated Filament Guide. Edit October 15, 2017: Enhanced Strength by Adding Thickness. ... Introduced a Built-in PTFE Pipe Seat to Serve as the Filament Guide.

Replace the boot liner's blanking plate with a light insert to illuminate more space in the vehicle's trunk. ... Reduced by 1 mm to prevent impact during printing.

For cases where you don't have clearance for t-nuts, this version simply presses into the end of a 2020 extrusion.

This is my CREALITY CR-10, fully upgraded and functioning with numerous modifications. Mod 1: Extruder Mod 2: BLTouch Auto Bed Leveling System Mod 3: Glass Bed Upgrade Mod 4: Insulation to Achieve Stock Temperatures of 115c Mod 5: Custom Firmware...

To upgrade your CR-10's cooling system, using the original stock hotend, you'll require two 40x20mm blow fans mounted side by side.

To upgrade the CR-10's cooling system using its original stock hotend, two 40x20mm "blow fans" are required and should be positioned side by side for optimal airflow.

This is a minor revision to Gabriel3DCaster's Creality CR-10 Fan Mod 0.8mm shorter. My original fan duct broke at the screw mounts. When I ran Gabriel3DCaster's, I broke the fan mounts again just while cleaning it up after pulling off the printer. I...

WARNING: This design may exceed the clearance of Ender3 Stock Airflow due to its increased height. The original airflow has a fixed height of 9-10mm, while this remixed version stands at approximately 16mm. Verify your nozzle's height from the...

This is a remix of this https://www.thingiverse.com/thing:2792260. I first tried the MGN12H rails and they flexed a bit, so I decided to go bigger and use MGN15's instead. Keep in mind that you may need to upgrade your stepper motor to overcome the...

Here we are, folks! I've got some exciting news for you - the first prototype of the Y tensioner for the S5 version of CR10 is finally here! This baby's designed to work with a 10mm wide belt and an M5 bolt. I'm super curious to hear your feedback...

Some users requested this model, so here we are. The initial prototype of the Y tensioner for the S5 version of the CR10 is now available. Designed specifically for a 10mm wide belt and an M5 bolt, feedback is eagerly anticipated. Unfortunately, I...

WARNING: This may not fit on Ender3 Fan/Hotend Stock configurations because of its height. Ender3 Stock Airflow has 9~10mm Height, this remixed version is around 16mm height. Check your nozzle height from Airflow piece before printing this version or...

Mounted perfectly now! ...Photos are on their way too!

Photos are coming soon, by the way, the print turned out great, just not yet framed.

The Microswiss hotend sits a tiny bit lower than original Creality. ...This remix has a 1 mm lower nossle and reinforced screw ears.

I adjusted the x body from Cornely_Cool by loosening the tolerances by .3 on the body for where it fits into the 2020 extrusion because the tolerances were too tight. This made it easy to slide in very easily right after print without any extra...

I used the Z-axis linear rail mount from here (I used the spacer I created since the one located there appears to be the wrong size): https://www.thingiverse.com/thing:2974225 I used the Y-axis linear rail mount from here:...