cr 10 mini enclosure 3d models

The CR-10 EZABL clip is a sleek cable management system designed specifically for CR-10 printers enabled with EZABL technology. This versatile clip expertly secures the bowden tube, extruder power cable, and the essential EZABL cable in one...

Some handwritten G-code for leveling your bed, Designed specifically for the Creality CR-10 and CR10-S. It navigates the four corners and middle point with precision, Carefully avoiding the very edges and clips along the perimeter. This code...

You can print all parts with a Creality CR-10 or CR-10S printer and purchase: 8 bearings (16mm outside diameter, 5mm inside diameter, 5mm width) 8 M4x6mm screws 8 M4 washers 8 M4 nuts The required fasteners can be found in this box:...

I purchased some 4x4 vibration isolation pads for the CR-10 printer, so I designed legs that would securely hold them in place. Additionally, I wanted to leave room on the bottom of the printer for easy access to the bed and potential future addition...

I've relocated the original CR-10 holder upwards, necessitating a new guide to direct the filament in an arc towards the extruder. Thanks to SLICKASICE1805's suggestion, I revamped it. This updated design allows for four positions, each with a...

This takes your TUSH and allows you to easily mount it on top of the CR-10 control box. Hmmmm, that came out wrong. ;) In case you don't have this wonderful spool holder already, find it here: https://www.thingiverse.com/thing:2047554 I love...

... is helpful to the community. Since Sketchup files aren't supported on Thingiverse, here's a direct link to the file on the Sketchup 3D Warehouse: https://3dwarehouse.sketchup.com/model/8e4a0a6f-5c9b-48ed-bc92-eb1d7d02c322/Creality-CR-10-S4

I created this micro SD to SD card adapter mount in Fusion 360 from scratch, customizing it to utilize the stock hardware on my CR-10 printer. This design holds an additional SD card while still granting access to the USB port without requiring any...

Replacement for stock CR-10 fan duct This upgrade is a breeze to print, requiring minimal effort. Utilizing entirely stock components, you can easily swap out the existing setup by simply unscrewing, replacing, and reassembling - a task that takes...

This support is designed for CR-10 printers. It allows users to easily attach the spool holder to the left-top of their printer. To minimize friction, I installed two bearings with dimensions 20x47x14 mm. The installation process involves securing...

This sleek and versatile light is tailored specifically for the Creality CR-10, delivering exceptional results with its cutting-edge design. The light securely attaches to the horizontal rail at the top of the printer, a feature that may also be...

I recently found that operating the CR-10 on an ordinary table causes strain on my neck due to looking down at a 90-degree angle from the nozzle to the glass plate. To alleviate this issue, I created custom support legs that elevate the printer to a...

This bracket allows for easy installation of a flexion extruder on your CR-10. Ensure you have a pass-through coupler for the bowden tube to ensure proper contact with the flexion, which prevents filament bending and escape from the extruder. I...

This is a bracket to let you put a flexion extruder on your CR-10. Make sure you have a pass through coupler for the bowden tube so the tube makes contact with the flexion. That is what stops the filament from bending and escaping the extruder. ...It...

This is a precision-engineered phone mount specifically crafted for Creality CR-10 printers and accommodating iPhones wrapped in thick cases, with an adjustable grip capable of securely holding any phone up to 13.5mm in thickness. ...Due to its clever...

As many CR-10 enthusiasts can attest, one of the most frustrating aspects of printing with this popular model is dealing with the paper clamps that hold the glass in place. The traditional method of attaching these clamps can be a major pain point...

I decided to tackle wisps of filament winding around my CR-10's hot end fan, which was causing heat creep. To prevent this issue from recurring, I designed a simple fan guard that snaps onto the existing fan shroud without obstructing airflow too...

A simple slide-on/slide-off screen cover for the CR-10/S. Please note, this is crucial: Print the frame size at 102% and the cover at 101.5%. It took a few prints to figure it out right and I haven't had time to go back and update the dimensions.

I've been dealing with a bigger model on my CR-10, but it reached a point where my filament spool dropped off its holder, resulting in a massive waste of filament. However, I came up with a simple solution to this problem. To implement it, just print...

I wanted to experiment with creating a vibration dampening support for my CR-10, but I didn't feel like purchasing two full packages of racquetballs. So, I cut two in half and instantly had a solution. The friction fit perfectly onto the 2040...

This attaches your TUSH directly to the CR-10 control box, making it easy to mount on top. I'm glad that came out right! ;)\r\n\r\nIf you don't have this fantastic spool holder yet, check it out here:...

Just created my own Cr-10 standalone version. Nothing special, but looks quite nice. Things are still in progress and will be updated soon. you´ll need a new cable for the standard display, an adapter for the sd card input, some...

https://www.paypal.com/pools/c/81EmSoZNia donate now Watch my latest video: https://youtu.be/LHWfNRmciHM Check out the quality of my work: https://youtu.be/QK8BMIYVKOo I wanted to give a heads up so you can modify the cr 10 to make it more precise...

I also rotated to the proper printing orientation to save everyone a step. A simple mount for BLTouch (Smart) for the stock CR-10 setup. ...I've reclaimed pin 31 from the SD card to use for servo control.</p> <h3>Print instructions</h3><p>Licence:...

I created this frame because I wanted to gradually move the contents of my CR-10 control box underneath the printer. I'm using 2040 aluminum extrusion. Two pieces were cut for the entire length of the "Y" axis, and two more were cut for the entire...

Filament Guide System Installed for Enclosure and Spool Holder

Print Settings Printer brand: Creality Printer: CR-10S Supports: Yes Resolution: .2 Infill: 50%

... Whether you're a seasoned professional or an enthusiastic hobbyist, the CR-100's redesigned enclosure is sure to impress. ...Its sleek lines, rugged construction, and user-friendly interface make it the perfect tool for any task or adventure.

My trusty old CR-10 was taking too much horizontal space with the separate command box, while I did not mind it taking more vertical space. ...I know there are a lot of all-in-one solutions everywhere, but they involve taking the control box apart,...

Things you need: * 2x DB37 connectors (male & female) * Some cable * Some screws (spare screws from CR-10 will do the trick) * Printed connector box * 2x printed DB37 housing * Some patience when soldering all the wires I've used an old printer...