cr 10 max 3d models

Here is a bigger version of gulfcoast_robotics' handle bar freshly modeled and sized for the CR-10 Max. ... I'd suggest support on this one, and you'll need the Max to print it due to its size.

Here is a bigger version of gulfcoast_robotics' handle bar freshly modeled and sized for the CR-10 Max.I'd suggest support on this one, and you'll need the Max to print it due to its size.

Needed a model for my CR-10 Max to plan out dimensions for an enclosure. Can't find any anywhere so I did my own (mostly). Measured it by hand with a measuring tape so the only dimensions I am fairly certain are correct are the extrusions, the...

PTFE Suport for CR-10 MAX

I didn't like the bed cable rubbing on the frame of my CR-10 Max so I designed a cord saver. I am not a fan of the cable chains so this was my simple fix for it. This was designed to work with a 40mm x 20mm aluminum extrusion. Not sure if...

This tool holder was designed specifically for use with Creality's CR-10 Max, utilizing Solidworks 2019 as its development platform. The accompanying Solidworks Files, in addition to the .IGS, .STEP, and .X_T formats, can be found within a compressed...

This is my design for a CR-10 MAX extruder relocation system. To move the extruder next to the hot end, you'll need: A cable to extend the extruder motor and filament sensor Several extended M3 bolts The rest of the parts can be reused. You can see...

Here is the cable chain for the CR-10 Max that we developed in-house. The bed cables will need to be extended. Open the control box and the heater wires are bunched up and can be lengthened outside the control box without splicing. The thermistor...

... x-belt tensioner nut while leveling. I'm currently printing with this mount and it's working fine. If you're looking for the firmware, check out Marlin firmware for Creality CR-10 Max. I'll post my settings when I finish testing. ...Almost there.

This is a hard stop for the Creality CR-10 Max Y axis. The hard stop is attached to the inner part of the opposite rail where the limit switch is mounted. 3 M5x25mm screws and 3 slot nuts are required to hold it in place. ...This will protect the...

CR10 MAX extended feet. ...for when your printer is just barley bigger then your table. made for my CR10 max will fit on all printers that have enough space for them. also works great for silencing the printer a bit. ...

Filament guide for cr-10 max

The CR-10 Max Hotbed Line Support is designed specifically for use with the CR-10 Max printer's silicone-covered hotend.

For three-dimensional printing purposes, successfully printed and thoroughly tested on a CR-10 Max printer.

..since someone requested a cover for a CR-10 Max use the base form: https://www.thingiverse.com/thing:5177951

Created this insert to replace the spool holder that comes with the CR-10 Max. Created in Freecad. ...

Support for a filament detector no more sensor problems, the filament changes more easily. ... Hoping to help CR 10 Max 3D printer owners :)

Reworked and reinforced fan duct for stock Creality CR-10 Max. Holds securely in place with 3 M3x25 screws. ...Prints well without supports.

The CR-10 MAX edition features an upgraded Hemera Mount with integrated Filament Sensor and a dedicated BLTouch Mount for enhanced precision and reliability.

Reworked and reinforced fan duct for stock Creality CR-10 Max.Holds securely in place with 3 M3x25 screws. ...Prints well without supports.</p><p>Category: 3D Printer Parts</p>

I have created a custom spool holder with a capacity of 3,000 grams specifically designed for use with the CR 10 Max. ... In addition, you'll also need four M4x10mm hex screws and four T-Slot M4x10x6mm nuts.

I could not find a temperature tower g-code for the CR-10 Max, so I created one. WARNING: This is a g-code, which is specific to printer type. Do not use on any printer besides the CR-10 Max. If you want the STL to code yourself, use the...

I'm designing a custom bracket specifically for my CR-10 Max to stabilize the z-axis motors and address the inconsistencies in 3D printing quality caused by motor wobble. ...This modification aims to improve print accuracy and resolution, ensuring more...

https://youtu.be/mkPdSdNtDsk This cable chain for Creality CR-10 Max from extruder to hotend you will need: Four M3*15mm and nuts one ziptie Files to be printed: 1 Hotend top mount 1 Hotend bottom 1 extruder mount 1 C Clip 22 chain piece 22 chain...

This is an update regarding the X-Over to noisy 40mm fans on the CPU box of my CREALITY CR-10 MAX. I'm still in the process of upgrading, so please verify the dimensions before printing. ... https://youtu.be/lFZsA1jtPVQ

DONATE: https://paypal.me/JuanCMedina21?locale.x=en_US DOWNLOAD FILE HERE: https://www.prusaprinters.org/prints/97475-cr-10-max-y-axis-linear-rails If you are annoyed by the v-slot wheel on the y-axis, linear rails are the best solution for the CR-10...

Needed an e3D V6 drop-in mount for CR-10 MAX. This remix will not interfere with BL Touch mount and will let you keep the OEM fan. ... Supplies: (3) M3 Nuts   1x for top slot on backmount   1x for rear hexagonal hole on backmount   1x for lower...

Fan shroud for the PSU unit on the CR-10 Max. Model is done to minimise the material used, thus the wall is thin. I printed it with 0.6mm nozzle with 0.8mm line width (the wall thickness) and 0.3mm layer height. ... you can use a 0.4mm and push the...

Cable support for stock Creality CR-10 Max. It securely holds bowden tube and cables from the hotend/extruder. Avoids wearing of the cables due to the movement of the carriage. Prints in two parts, no supports. For attaching the parts together...

Cable support for stock Creality CR-10 Max. It securely holds bowden tube and cables from the hotend/extruder. Avoids wearing of the cables due to the movement of the carriage.</p><p>Prints in two parts, no supports. ...For attaching the parts together...