cr 10 lcd screen 3d models

It's a fully printed enclosure for the CR-10 that really works well! I had tried ABS and nylon on the printer before with some pretty bad warping issues, but it was all about keeping the heat around the part instead of letting it float away and warm...

We connected the main power line from the CR-10 to relay 1's center post using 16 guage wire, then linked relay 1 to the main power on the motherboard with smaller wires. We used the following components: Raspberry Pi 3b:...

This is primarily a remix of Kiayoto's CR-10 enclosure. I removed the lower section of that enclosure and modded several pieces of the original. I had printed all of the original parts then made adjustments to suit my needs. I also modded the...

Hopefully this beacon will speed my CR-10s up when I throw some speed 3 modules in it. ... It might not be compltely flat so it wont hurt to lower it down into the build plate .1mm or so https://youtu.be/-ptA6_WomfQ

Hopefully this beacon will give my CR-10s a boost in speed when I install some speed 3 modules. It might not be perfectly level, but lowering it down into the build plate by just 0.1mm should make no difference at all. ...Check out this video for more...

My CR-10S has been converted to be all-in-one, so the feet dimensions are probably different than a stock CR-10S. Additionally, there is no control box that needs space to the side. It screws in with #8 1/2" wood screws to assemble the back supports...

I did a fair amount of searching and wasn't satisfied with the cost or design of several of the enclosures available for the CR-10 and other larger printers, so I decided to design my own. This enclosure is fully-customizable and can be scaled up or...

My CR-10S has been converted to be [all-in-one](https://www.thingiverse.com/thing:3513661), so the feet dimensions are probably different than a stock CR-10S. Additionally, there is no control box that needs space to the side. It screws in with...

... you need to print all additional parts - door and hinges.) Print with support and skirt. Pictures are from the first design with 2 mm walls. The second design comes with 3mm walls. https://pinshape.com/items/44114-3d-printed-cr-10-s-enclosure

I created this frame because I wanted to gradually move the contents of my CR-10 control box underneath the printer. I'm using 2040 aluminum extrusion. Two pieces were cut for the entire length of the "Y" axis, and two more were cut for the entire...

Ventilation cut-outs on the CR-10S proved subpar; I had to enlarge holes for improved airflow and install wire-mesh guards around each fan. A custom adapter plate was 3D printed for seamless integration with these new guards. Additionally, I drilled...

Although I had already replaced most of my printer's original extruder and hot end parts, I wanted this new setup to reuse as many of the original parts as possible from my Creality CR-10S when I bought it. The resulting system consists of two main...

A humble light fixture that required only a brief 10-minute creative spark to bring to life.

Initially, I found the concept intriguing but realized it wouldn't suit my Creality CR-10S due to its relatively low profile. ... To rectify this issue, I embarked on a complete redesign, incorporating several key modifications: -the ring has been...

I then came across tinymachines shipping their CR-10s equipped with spring caps, which got me thinking. So, I quickly whipped up some caps using Tinkercad. It's probably a good safety precaution to prevent springs from digging in and causing...

... screw for one that's approximately 8mm in size. Cut a foam pad to 34x49mm and attach it securely to the piece. Keep in mind that the hole needs to be precisely 10 mm deep, so make sure to purchase foam that's thicker than this minimum requirement.

A precision-cut hole, measuring 10.5mm in diameter, securely cradles the pen in place with a clamping screw that keeps it firmly attached, all without requiring removal of the metal fan box. ...This thoughtful redesign also elevates the pen holder above...

The wood piece sizes are as follows: Front/Back - 18 inches by 25.5 inches (the door is however big you want it to be) Right Side (Front) - 12.5 inches by 25.5 inches Right Side (Back) - 11 inches by 25.5 inches Left Side (Front) - 12 inches by 25.5...

Firmware: https://www.dropbox.com/s/04qdk2hp6wgbifb/Firmware%20-%20Cr_10_TMC%202100.rar?dl=0. ...Links:...

Slim Case for LCD Screen Discount RepRap Full Graphic Smart Controller, Part Number 12864 - A Ubiquitous Screen Option. 4mm Thick Plates Are Assembled with 10 Units of 4-1/2" Walmart Wood Screws. ... Designed Exclusively for the Reach 3D Printers...

Keep in mind that the area surrounding the LCD screen must be clear of any obstacles, as it doesn't touch the buttons but covers the actual LCD screen. Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.15 Infill: 10% Notes:...

The "Anycubic Kobra LCD Screen Protector" rotated, so you don't have to rotate it

Utilize a full-screen 3D printer LCD display or an equivalent model of similar dimensions.

LCD Screen 5 inch 640x480 display mount for 737FMCCDU V3 by dotsha747

I designed this simple Ender 5 LCD Screen Relocation plate to make my life easier

... function at its best, it demands a precise distance to pull up the screen into its flat position. ...A notable height discrepancy exists between the original LCD screen on the Anycubic Photon S and the Elegoo Mars screen, measuring between 0.7-0.8mm.

For each one missing, you are losing 0.25 to 0.50mm of LCD pixels from the screen's mask. Use this to calibrate your slicer's printing envelope. The normal screen size is: 120.96x68.04mm. ... Resolution | 2560x1440 Pixel Pitch | 0.04725mm by...

Cr-10 smart e3d CR Revo mount for the auto leveling

Cache Courroie X (Belt Holder) for CR-10/CR-10S. ... Standard Unmodified Version Shared.

Elevate the CR-10/CR-10S enclosure by raising it. ...Prevent overheating issues effortlessly.