cr 10 fan upgrade 3d models

Hello there :) This is my upgraded Fan Shroud for my X5SA (I love that thing) managed to print at ~300mm with 8k acceleration. ...Just need a appropriate cooling solution and the dual 5015 fans are up for this task.

Modification for the original Creality CR-10 control box; replaces the three loud fans inside with either one or two 120mm fans. Print 2 of these stands and fit either one or both with 120mm fans (no screws required). If you only fit one fan, I...

Feet for use with replayreb's awesome CR-10 Dual 120mm fan bigery case remix ( https://www.thingiverse.com/thing:2839191 ). He designed his for use with rubber feet that you can buy online. I didn't have any rubber feet so I used the dimensions and...

I compile a selection of practical models and redesign them to create something entirely new. ... This compilation is specifically tailored for the CR-10 Stock HotEnd setup. ... I hope you find this revised design appealing.

I gather relevant models, rework them, and integrate them into a cohesive whole. ...This particular iteration is tailored to the CR-10 Stock HotEnd setup. ...I'm eager to hear if you find this solution satisfactory!

I am designing a chimera+ mount for my creality cr-10. My attempt is to design a mount which does not reduce the print volume (and prints with minimal support with my old, one extruder only, setup). Probably 1-2cm z-hight is lost, but at least x and...

... of the underside of that overhang test print, but unfortunately, I used clear filament and those pics are pretty much useless now. Print Settings: Printer: Creality CR-10 Rafts: Don't matter Supports: Yes Resolution: 0.1 to 0.2 mm Infill: 35%

I designed them to be used with the original rubber feet from the CR-10 frame that I had removed and switched to squashball feet, but wanted to reuse them. The feet are designed to be glued on to the box after it is attached. There's a small port and...

Here is a remix version of Imagine That Titian/Atlas, Creality CR-10, Afinibot A31 Print Cooling by RebelRousingProps. Here are the improvements I've made. 1. The original design fails to accommodate my 50 x15 mm part fan due to its actual thickness...

We're excited to announce that a revolutionary new cooling system is on its way, designed specifically with CR-10 owners in mind. Say goodbye to overheating worries and hello to smoother, more efficient prints. ...Stay tuned for more information on this...

See my previous designs here: - [Satsana Ender 3 Fan Duct](https://www.thingiverse.com/thing:4369859) - [Satsana 5015 Fan Duct for Ender 3 / Ender 5 / CR-10 ](https://www.thingiverse.com/thing:4528533) ## Dual 5015 Part Cooling Blowers Hopefully...

I discovered it easier to remove and adjust the fan duct mounting height, which allowed better cooling of the two screws on the CR-10 and heat break if desired. Having a thin layer of cool air around and not being touched by plastic that heats up...

This is a remix of [CR-10 Fang for 40x40x20mm Fan Cooler](https://www.thingiverse.com/thing:2683629) by SanderPuh. #Why this remix? The main reason was that when I printed the original fang, the support (meant to be fixed to the two hotend screws)...

**UPDATES:** I added v3 -> plate thickness increased from 2.2mm to 4mm and changed angle of legs to fit the full width of 140.2mm [![noise comparison](http://public.kraxner.tirol/CR-10_LautstaerkeMods.jpg "Noise...

This upgrade enhances printers such as CR-7, CR-10, Ender 2 and Ender 3. The PTFE insert is secured by an additional extrusion that seals off the gap in the extruder where TPU normally gets jammed. Adding a rubber to the steel-roll also optimizes...

This Upgrade Includes A Triple Fan Nozzle Cooler. **Critical Information Ahead!** As Per The Attached Picture In The Files, We Have Connected Two Fans Together To Maximize Cooling Performance. The Specifications For Each Fan Are Listed Below: We...

It's not flawless, but it functions with a 40 x 40 mm fan (10 or 20 mm). The setup includes two screws on top and either two or four 15 mm M3 screws to secure the fan in place. To minimize vibrations, some rubber or silicone is required to create a...

- I can actually carry the entire psu just by grabbing the fan :) For those of you who are worried about vibrations: I have mine running and can only tell that it is, when putting my ear right next to it. (So no problem at all!) Please ignore bad...

I've been running a Fang fan duct for a while now, but after considering switching to a direct drive setup, I realized that the high, top-mounted fan would obstruct my extruder. So, I drew inspiration from the Ultimaker 2 fan configuration. My...

This is a soundproof cover for the rear exhaust fan on a CR-X base. ... Reference https://www.youtube.com/watch?v=RRbvASlom4A&t=91

... my CR-10s and continue to use them with great satisfaction. All of these mods or enhancements are essential for anyone just starting out with a CR-10s - I'm convinced they're also a must-have for CR-10s S4, CR-10s S5, and even the standard CR-10.

Or view the image in full resolution at https://spaxi.at/CR-10_LautstaerkeMods.jpg If you have any questions, feel free to message me. ... UPDATES: added v3 -> plate thickness increased from 2.2mm to 4mm and changed angle of legs to fit full width of...

New version with 404010 fan. ... More air Flow and lighter.

Remix for smaller printer . ...2 x 92mm fan

2 x 120mm Fan 4 x M3 x 30 2 x M3 x15 1x LM2596S LED

NOCTUA fan support for motherboard; valid for Noctua models NF-A4x10 and nF-A4x20

Micro Swiss dual blower and fan shroud - Will add directions soon

Micro Swiss dual blower and fan shroud Will add directions soon

The Xenofang Fan Edition for the CR10 comes in a 40mm size.

* * In the following example, the X and Y offsets are both positive: * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 * * +-- BACK ---+ * | | * L | (+) P | R <-- probe (10,10) * E | | I * F | (-) N (+) | G <--...