cr 10 e3d v6 upgrade

Installing an E3D v6 hot end to Anycubic Kossel is a challenging task that requires more than just a few compatible parts. Many claim it's easy, but this is far from the truth. The genuine v6 hot end has distinct differences compared to Chinese...

The fan fits securely, but still has some clearance to rotate freely around the E3D heatsink. ... I printed this design in NylonX for its flexibility, which I believe is ideal for this application, although all materials should work well too - I just...

CR-10 carrier is https://www.thingiverse.com/thing:2789191. I am extremely grateful for the designs! I'm also considering those fan mounts by https://www.thingiverse.com/thing:3017420. Update 12.06.19: The bracket hole was modified in v2, which...

... temps will not be true at 215C! My settings are now "M305 P1 T93500 B4388 R4700 " I broke my extruder drive plate finding this out, so have included the plate, & a motor spacer upgrade which allows you to use a M3x16bolt to reduce the plate strain.

Please note if you use stock E3D V6 'cartridge' sensor you will need to change it in the firmware to value no. 1 from 5. You can find and replace with the code below. ... #define TEMP_SENSOR_0 1 If you're looking for the connectors on the board...

CR-10S Pro E3D V6 Mount. You can utilize the petsfang with either a single fan or dual fan from https://www.thingiverse.com/thing:2759439. I've modified the mount points for the petsfang, as I use the standard E3D V6 Hotend. Note: Apply Aluminium...

This conversion plate resolves the length discrepancy with E3D hotends and their replicas supplied by Anycubic. To implement it, simply insert this adapter between the standard housing and the original "ring" that fits into the hotend. ...It functions...

I created this duct to be used between the original E3D duct and the E3D fan, so you can still use the original part on your MendelMax 1.5+ with a 50mm X axis spacing. To print it out: - Use at least three walls and two top/bottom...

Minimal changes required easy upgrade, requires a couple of M3 threaded inserts>Z_PROBE_OFFSET_FROM_EXTRUDER -0.95 # Z offset: -below +above [the nozzle] >X_PROBE_OFFSET_FROM_EXTRUDER -20 # X offset: -left +right [of the...

In my adaptation of the upgrade plate, featuring the original fans and an 18mm capacitive sensor, I drew inspiration from various other projects. Unfortunately, there were errors in my previous design; I aimed to place the sensor at the lowest...

This is my updated upgrade plate, featuring the original fans and an 18mm capacitive sensor. It's based on a few other projects, but I made some critical mistakes in the previous version that needed correction. My goal was to position the sensor at...

... pass through the print sideways, be extremely cautious with your tap and go slowly or the part may crack. Try increasing your print temperature by 10 degrees when printing the sliders; the extra layer adhesion should make them slightly stronger.

We upgraded an existing hotend mount on Thingiverse for better fit and ease of use. This hotend mount correctly mounts a titan extruder, while the original version did not (the stepper mounting plate was too thick for proper tightening of the titan...

Unfortunately, while he includes a version which fits the E3D V6, it seems that there was a slight design revision in E3D's heat sink in 2022 which means that his model does not fit.I took the opportunity to make some changes:Now fits the E3D V6 heat...

Crisis Pro E3D V6 Mount Needs M3*20 screws, three in total. ...Additionally, four to five M3 screws are required, each about two inches apart.

The result is a rock-solid build that perfectly pairs the E3D V6 hotend with a robust 5015 fan and a stylish light. You can find the same light I used here: http://a.co/7q8d69D, http://a.co/2nyPGR8 - it really makes this build shine! ...This was just a...

This mount enables me to install the E3D V6 on my Creality CR10S Pro while reusing existing parts; it does not affect anything else besides the hotend swap, making it the simplest solution I've found and one that works flawlessly. The original...

Remixed bed level mount to accommodate the Creality CR touch. ... The modification needed was a small notch for the cabling and expanding the channel near the mounting screw.

A mount for an E3D V6 All Metal Hot End to fit on the CR6-SE. I had found another but it was built for a clone, and the geometry of one I have appears to be different at the top where the mount would go, so I had come up with something on my own. The...

For those who've already been using the CR-10 Heavy Duty customisable modular e3D V6 mount Volcano 5015 ABL by Chito, but want to leverage the new Petsfang duct, this remix seamlessly integrates the mount points of the Petsfang to fit the Chito...

This is a Direct Drive mount for Ender-3 & CR-10 using the original X-Carriage plate for my particular combination. ... I am using the original X-Carriage plate with the dual-gear extruders (Winsinn) and J-Head V6 with Volcano Hot-End.

A new hotend and Orion Piezo mount bolt onto the existing CR-10 metal mount, allowing the use of an Orion Z-probe with fans for cooling E3D and part cooling. Uploaded two prototype mounts adding Zesty tech Nimble support to this mount on 22/10/2019....

There is a space to the left of the stock E3D V6 fan for all the wires to run. Marlin Code ------------- • For the BLTouch, use the below. Measure after installing in case of printing variations. X_PROBE_OFFSET_FROM_EXTRUDER -46 (was -49 prior to...

This mount will work with the new 40mm nema 17 that now ships with the updated Titan Aero from E3D. You can also use the mount for the 25mm pancake motor too. Loosely based on the mount my CNCKitchen here: https://www.thingiverse.com/thing:2756792...

Upgrade for CR-10 with BTT TFT35 new 3D printer for small money.

MDG CR-10 V3 UPGRADE PROJECT Official Site: **[MAKERS DEVELOPMENT GROUP](https://www.makersdevelopmentgroup.com)** MDG CR-10 V3 Project Link: **[MDG CR-10 V3 UPGRADE PROJECT](https://www.makersdevelopmentgroup.com/cr-10upgradeproject)**

This is a model of the coupling that threads (M10) into Creality's modified version of the E3D V6 heatsink for mounting to the E3D Titan direct drive extruder. I suppose you could print this, but my intention of sharing is for it to be used as an aid...

I've built an upgrade for the subpar filament holder on my Creality CR-10 2. The gap between the ball bearings can be customized using a hand crank. The main bracket is secured in place by a large nut. ...To get started, you'll need two ball bearings...

Upgrade your CR-10 OEM spool holder for a smoother printing experience. Say goodbye to spools that sit off center, swing erratically and misbehave. This upgrade likely works for many brands as the arm is standard on numerous models. The insert is...

Fan Duct for CR-10 Designed to Work with E3D V6 and V6 Volcano Features: 1: Adjustable Nozzles Can Be Moved Up and Down, Rotated for Complete Air Direction Control. After Setting, Tighten a Small Set Screw in Front to Prevent Movement. 2:...