cr 10 e3d v6 upgrade

A compact and efficient hotend designed specifically for use with a 40mm cold-end fan and a powerful 5015 blower for optimal parts cooling. This hotend is engineered to fit seamlessly within the x-carriage dimensions, allowing for a streamlined...

This text appears to be a set of update notes and installation instructions for a 3D printing project, specifically a custom duct system for a 3D printer called "Hero Me." The updates cover various changes made to the design, including improvements...

Ender 10S Upgrade Power Supply Control Unit Stand Best Creality CR-10/S/V2 Upgrades & Mods elevates the control unit about 2.8 inch - 7.3 cm helps in good unit ventilation and better cooling easier access to the sd card avoid grounding electric...

... specifically suited for 30mm fans. However, users might want to consider upgrading to a 5015 blower for enhanced performance, as the current 30mm fan may be insufficient; nevertheless, any improvement over the original is beneficial.

This is for someone who wants to upgrade their Da Vinci Pro 1.0 to direct drive and to work with the E3D All-metal v6 HotEnd. I used the E3D Titan extruder with a modified heatsink cover to fit the E3D v6 Volcano. This requires cutting off the old...

My TinkerCAD parts include: 1.75mm E3D v6 Extruder ver03 rev06 [supports removed], 1.75mm E3D v6 Extruder ver03 rev06, and 1.75mm Extruder Idler ver02 rev05. The Idler Latch is ver00 rev00, and the Extruder Washer is ver00 rev01. From LulzBot:...

Printable Mount Kit Compatible with CR-10S Pro, CR-10 Max, and E3D Hemera - Includes Fan Duct, BLTouch, and EZABL Mounts. ...EZABL Mount Requires Additional Testing Based on Detailed Measurements

When upgrading to the E3D V6 hot end, it is strongly recommended to also replace the original power supply, otherwise the printer won't be able to "feed" the hot end power demand. I've replaced mine with a 12V/20A power supply. The hot end is...

While a metal heat break swap might be sufficient, this upgrade is intended for those who want to replace the entire stock hot end assembly with genuine E3D parts. You will need (for each side): (4) M3 bolts that are 8 mm long for mounting the...

DEUTSCH:Anycubic Vyper - Adapter for V6 E3D v.1.0 upgradeGenervt vom ewigem Nacharbeiten des Adapters von RyanMaverick, habe ich den Adapter nochmal nachgearbeitet und den unnötigen Steg herausgenommen.Nun passt der Adapter ziemlich gut (auf jeden...

I designed parts for Trianglelab 3:1 geared extruder, E3D V6 hotend, and Nema17 pancake stepper motor upgrade. The controller board is CKY-V6-191017 The stock extruder motor from Tronxy uses about 1.4 A, which was overheating the Nema17 pancake...

I designed this quick release spacer after the one I tried to use was very loose and not designed correctly. ...This one is as close as I can get to the original factory model except with the correct thickness for the E3D V6 Hotend.

This mod utilizes existing components (extruder plate, blower fan) for the E3D v6 hotend, BMG (clone/original) extruder, and pancake NEMA stepper motor - standard NEMA steppers also work. The design guarantees that no space is lost on the X axis due...

Humans fill the space completely at a rate of one hundred percent absorption.

The fan mount is adjusted upward to accommodate larger and more powerful 40mm fans.

This new version is as close as possible to the original factory model, but with the precise thickness required for the E3D V6 Hotend. ... Print Settings: Printer Brand: Robo 3D Printer Model: R1 ABS + PLA Model Rafts: None Supports: None Infill...

DEUTSCH:Anycubic Vyper - Adapter for V6 E3D v.1.0 upgradeGenervt vom ewigem Nacharbeiten des Adapters von RyanMaverick, habe ich den Adapter nochmal nachgearbeitet und den unnötigen Steg herausgenommen.Nun passt der Adapter ziemlich gut (auf jeden...

... The E3D Threaded Bowden Coupling can be found at https://e3d-online.com/catalog/product/view/id/8625/. When using this version, I've discovered that trimming the filament at an angle is necessary so that the point aligns with the side of the gear.

... The shroud fits perfectly against the heavy-duty CR-10S/E3D-V6 mount, courtesy of Graham - https://www.thingiverse.com/thing:2471011. ... If you've tried several CR-10S part cooling fan shrouds without success like many others, give this one a shot!

Added air nozzles for Volcano V6 hotend. I changed the horseshoe so screws M3 x 20 mm are long enough to reach nuts in the pocket. I realize this problem after print testing model. This is second version of the effector for Anycubic Kossel Linear...

I'm excited to create a remix of Kakadus original fanduct, utilizing his mount points and fan position/angle - but in a much more straightforward way to print. Version 1: I opted for a 40mm fan, secured with two holes on the flat side. As for my X...

I opted to steer clear of all the unconventional conversions floating around, instead choosing to keep my printer's design refreshingly straightforward. To achieve this, I crafted a spacer that effortlessly takes care of the task at hand when...

As I wanted to avoid bowden in my printer, I modified Don1337's design so it could be used as a direct extruder. The fan duct for the heatbreak I'm using is from IsmaelPR1's model. I'm also sharing the blender file here for anyone who wants it.

Compact hot end mount design, easy instalation, recommended adding connectors close to the head for hotend swapping, requires M3 threaded inserts. ... *added another version for no inserts Probe offset Nozzle-to-Probe offsets { X, Y, Z } #define...

Required screws 2x M3 x30mm for the hotend, 4x M3 x20mm for the fan and the strap.

Manufactured with reinforced walls and precision-cutouts for secure mounting. ...Crafted from high-quality PETG material.

I compiled a collection of parts I used to assemble the E3D Hemera on my CR-10 V2. You can access all files from this Thing's files page, but please give credit to the designers as listed (see links). This compilation consists of: The primary...

Update: To further enhance functionality, I integrated the upgraded Double Fan Mount v2.0 for E3D v6 fusor, seamlessly incorporating the BLTouch mount within the design. ...Following this revision, I reconstructed the entire model to address previous...

This extruder mount is crafted to maintain the nozzle's position in close proximity to the stock's original placement, thereby ensuring that your printing area remains unaffected. It boasts a sturdy yet lightweight design and features a designated...

It's a version 2 mount for E3D V6 Volcano Titan Direct Drive Extruder (Right Sided), designed for replacing original X axis aluminum mount. Might need to accomplish whole set with another left side Fan Rack design in my library. Better use...