cr 10 dual z sync 3d models

Adjustable Z stop for the Creality 3D CR-10 Large FDM 3D Printer. ...

You will either need to have longer Z screws or a slight reduction of Z height. It also has a bearing pusher in the model included so you use it. ...If you dont use it and you push on the center, you will kill your ball bearings (If your a mechanic,...

You will either need to have longer Z screws or a slight reduction of Z height. It also has a bearing pusher in the model included so you use it. ...If you dont use it and you push on the center, you will kill your ball bearings (If your a mechanic,...

Install a mounting bracket onto the CR-10 using this setup to enable dual extrusion capabilities. ...The secondary extruder is positioned directly to the right of the primary unit.

Typically, the upgrade utilizes a 760mm timing belt, but I opted for a 784mm strap instead. Preparation was necessary to accommodate it. ... To execute this modification, you will require these components: * Two GT2 Bore 8mm 20 Teeth Timing Aluminum...

The ultimate solution to perfectly calibrate your Creality CR-10 S5's Z-axis is undoubtedly the ingenious "ZMatic".

This is a Remix of baschz's Z-Axis adjustment knob for the CR-10. I reused the cover plate, which works perfectly and "reverse engineered" the thread from his STL file since I couldn't find a suitable thread profile within Fusion 360. Instead of the...

Please consider upgrading to a dual Z-axis setup or using a stronger stepper motor for better results. I personally use the original stepper motor with single lead screws, and it works fine as long as the stepper drivers are active. Print this...

I've bought a Dual Z kit for my CR-10, and before installing all the pieces, I took some measurements and drew them in 3D. My plan is to take precise measurements of each piece that might come loose from the printer for any reason. Here's the OEM...

Adjustable Z-endstop bracket for CR-10(S), I needed one because I lost the old stock one and I wanted it to be height adjustable.

This is to improve the Z-axis sensor on Creality CR-10. ... The devices allow the sensor to have an adjustable height.

) dual z-axis upgrade or using a stronger stepper motor for Z-axis.please print this with ABS as PLA will become soft if your motor overheats temp is high or you do long prints.zip ties are required to hold in the Wires.a little bit of bends is...

Dual Extrusion System Upgrade: Installing a CR-10 Linear Rail Mount Upgrade your 3D printing experience by incorporating a reliable and efficient linear rail mount system designed specifically for dual extrusion setups. This innovative solution is...

... once I have time to create them. WARNING: The Wanhao Di3 doesn't come with dual extruder support, so my board and several other parts aren't standard. CR-10 Micro Swiss Hotend: https://store.micro-swiss.com/products/all-metal-hotend-kit-for-cr-10

I recently purchased a Dual Z kit for my CR-10, taking precise measurements before installing all the components to ensure accurate assembly and future disassembly if needed. As part of this process, I'm documenting the OEM support 34mm Nema 17...

Due to the fact I've purchased a Dual Z kit for my CR-10, before installing all the parts, I took some measurements and drew them in 3D. Really, the plan is to take measurements of all the parts that will be casually dismounted for any reason from...

This two-piece part supplants and amplifies the acrylic stock cover on the Creality CR-10's Z-axis lead screw; It allows you to manually control the hot end up and down when steppers are disabled, a feature I have found extremely useful at times. For...

**#ZKNOB** This two-piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw. It lets you manually control the hot end up and down when steppers are disabled, which I have found to be very handy at times. For...

Creality Ender 3 users please read the last update below #ZKNOB This two piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw; It lets you manually control the hot end up and down (when steppers are...

This plate mounts under the CR-10 V2 runout sensor and aligns it with the new extruder.The extruder I am using is a Redrex brand. There are two versions of the model. One has countersunk holes and mounts to the CR-10 using 4 M3x12 flat head...

I purchased a Dual Z kit for my CR-10, so before installing all the pieces, I took some measurements and drew them in 3D. My plan is to take measures of every part that might get dismounted from the printer at any time. Here's the OEM support for...

#ZKNOB This two-piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw. It lets you manually control the hot end up and down when steppers are disabled. I have found this to be very handy at times, such as...

This is a Dual Damper Bracket for the CR-10, inspired by https://www.thingiverse.com/thing:2793110. Key Features Include a Filament Sensor Holder. Bolts Directly to the Carriage. Mounts Using Existing Hardware - We Recommend Getting Slightly...

Redesigned E3D V6 mount and dual cooling system now perfectly fits Creality CR-10. A precision cutout accommodates the bolt on the bottom of the stock carriage. I've yet to print this design, but a detailed mock-up provides a clear visual reference.

Creality Ender 3 users please read the last update below #ZKNOB This two piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw; It lets you manually control the hot end up and down (when steppers are...

This sensour housing is a littlebit mor wider, so that the tube matches directly into the extruder of the CR-10 V3 if you use this holder: 4934731_CR-10_v3_Filament_Sensor_Holder

This mount has a dual extruder setup with one filament cooler and, once both E3D V6 are installed, it's about the same height as the original CR-10 Extruder. The Hotend Coolers come from this source: https://www.thingiverse.com/thing:354723, but...

This easy-to-print Z-axis stabilizer is designed specifically for CR-10 and CR-10 S4 printers, allowing users to utilize 1 inch tubing as the Z-axis reaches its maximum height. A modified left-hand top stabilizer has been added to accommodate full...

This dual fan filament cooler has the same height as the original CR-10 Extruder after mounting the E3D V6 and optimizes airflow for cooling the filament, not the hotend. I've also modified the Hotend Cooler https://www.thingiverse.com/thing:354723...

Designed a custom CR-10 Direct Drive mount by merging ideas from two pre-existing Thingiverse mounts and tailoring it to meet my specific requirements.