cr 10 bl touch 3d models

Clean up your sprite extruder equipped with BL-touch. ...Check out the bltouch cover in my designs.

Mount a replacement for the existing stop switch using a BL touch sensor, set to 802 milliamps.

This was modified to attach both the BL Touch and the Creality laser to the Ender 3 Pro.

I designed this BL-Touch Nozzle Calibration Aid to help you fine-tune the BL-Touch automatic bed leveling probe to the precise height above the nozzle's tip - exactly 8 mm from the bottom of the probe's body (not its tip) to the nozzle's tip. This...

This is a BL/3D/CR Touch mount that is shorter than normal to better fit in cases where the hotend is shorter than usual. This raises the touch sensor higher than with the mounts that come with the 3D Touch. It's made to fit the Creativity Direct...

Anet A8 BL Touch Mount A mount to hold a BL Touch Sensor to an Anet A8 I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then...

Anet A8 BL Touch Mount A mount to hold a BL Touch Sensor to an Anet A8 I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then...

Man benötigt bei beiden Haltern 2 Schrauben M3 die 10 mm länger sind als die originalen und zwei Schrauben M3 x 12 für den BL-Touch. Der Halter war ursprünglich 5 mm stark aber das war mir zu instabil, deshalb hab ich ihn 10 mm stark gemacht und noch...

Shaved off the front and rear to make it look less bulky, raised the BL touch by 2mm for better clearance while printing. ... Offsets: Define X_PROBE_OFFSET_FROM_EXTRUDER -28 Define Y_PROBE_OFFSET_FROM_EXTRUDER -40 Define Z_PROBE_OFFSET_FROM_EXTRUDER 2 ...

Wombot BL Touch Calibration Tool adjusts your BL Touch to sit precisely 1mm above your nozzle. Lower the nozzle gently until it touches the rounded section, being careful not to push too hard and causing any movement. Then, position the BL Touch onto...

After upgrading to the new extruder for my Cetus, I realized that I had to mount my BL Touch / 3D Touch in a different way. So, I designed this new mount, which isn't extremely complicated to print. However, I highly recommend using ASA or ABS, as...

I lowered the BL Touch mount just a bit because the original version was too high for me. ...I lowered it by a m3 nut's thickness

A minor tweak is needed to expand the cable passage. ...Unfortunately, attempting to force the BL touch connector caused damage to the mounting bracket.

Fokoos fan cover, has the bl touch mount what is adjustable and opened up the blower fan intake 3MF are the same parts

Fokoos fan cover, has the bl touch mount what is adjustable and opened up the blower fan intake 3MF are the same parts

another BL Touch mount for a lulzbot hemera I recommend removing the wiper pad or the wipe sequence from the start script to prevent damage to the probe

Designed up this mount to use BL touch for anycubic kossel. ... Set nozzle to probe offset (0, -36, XX) Printing: No support Infill 30% or full

Installing BL-Touch on Ulti-Chimera. E3D V5 and E3D V6 Variants. ...Offset Settings: X: Set to Zero Y: Positioned +19 Offsets.

As far as I am aware 3d touch that I have is a clone of the Bl touch so the Bl touch should work. Print on the base that you would mount the touch sensor and use supports, I tried it flipped with no supports and did not like turn out. I have...

This machine comes with Creality V4.3.1 Board which is similar to other Version 4.x board come with a stm32 (ARM) MCU, but with no farther detailed information if any pinout changes, also the machine comes with a nice touch screen which could be a...

This machine comes with Creality V4.3.1 Board which is similar to other Version 4.x board come with a stm32 (ARM) MCU, but with no farther detailed information if any pinout changes, also the machine comes with a nice touch screen which could be a...

A mount to hold a BL Touch Sensor to an Anet A8I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then screwed back in place over...

This print serves as a straightforward corner-to-corner, single-layer aid to facilitate precise Z-offset adjustments with your BL touch setup. ...It also functions without the need for BL Touch or ABL, enabling real-time bed level adjustments and...

The default klemco design has one arm for the fan and another for the bl touch arm.  This moved the bltouch to the far edge of the build plate. ... I combined them into one arm so the bl touch isnt on the edge of the bed.

... of Iamthebadass. ...This iteration swaps out the conductive sensor bracket for a BL Touch bracket. As I await delivery of my own BL Touch, this design remains untested. ...If you decide to give it a try, kindly share your findings – did I get it right?

... for an ADXL345 accelerometer to the permanent BL-touch mount. ... If you already have a permanent mount and cabling for a BL-Touch, might as well throw in a mount for an accelerometer. ... This is just a first go at it, no testing has been performed.

Support for CR-Touch developed for CR-200B hotend.

Unfortunately, the screw on my BL touch had worn out too much to adjust the height of the measure tip. ... As a substitute for the original sensor, I used this clone from Aliexpress: http://bit.ly/2McIHrB The approximate offsets for the new sensor are...

remixed this remix as the orig had errors in the stl shaved off the front and rear to make it look less bulky, raised the bl touch by 2mm for better clearance while printing offsets: define X_PROBE_OFFSET_FROM_EXTRUDER -28 define...

Summary The current release of EVA 3.0 needs another BL-Touch mount. Here is my design. ...This places the BL directly in front of the hot end nozzle Print Settings Printer: RatRig V=Core Rafts: No Supports: Yes Resolution: 0.2mm Infill: 55% Filament...