cpap stand 3d models

This model is designed for a project on Hackaday, specifically for creating individualized nasal CPAP cannulas for preterm babies in critical care units (NICUs). The goal is to address the issue of limited available sizes for these delicate devices,...

This is an adapter which will allow you to attach a standard CPAP hose to a Versaflo M-200 mask (I'm guessing it will also fit other Versaflo models, but the only one I have is an M-200). The tolerances are pretty tight (intentionally, since this is...

By combining the driver with a half-mask featuring modified exhaust valves to create positive pressure, CPAP NIV ventilation is achieved. Adding a solenoid valve for controlling compressed air flow allows for BiPAP functionality. With a differential...

CPAP PPC Sleep Apnea Apnée du sommeil Hanger Holder support

Refactor of the RatRig electronics_wire_guide_rear to support a CPAP hose.

This is a remix of: https://www.thingiverse.com/thing:5202213 For a Biqu H2 V2S Lite allowing a CPAP hose to be used for cooling. ...Using the standard 22mm cpap hose

... infectious transmission risk. Advantages of CPAP: * Sufficient supply * Mature solution * More advanced than original ventilators * Low price Disadvantages of CPAP: * Ineffective for critical patients * Requires prevention of aerosol infection

Replacement strap clip for a BMC iVolve F1A full face mask.

I designed a clip and socket combo that would come in handy for securing a strap. To ensure structural integrity, I printed it with supports enabled on every layer, resulting in a robust final product. ...The model was printed upright, with the closed...

<p>A hose coupler for a Mirage Quattro mask.</p> Category: Replacement Parts

the original looked great, but the mask my spouse uses was a bit smaller. ...so I did a dirty trimming on the hook so it would fit without having to Dremel off the excess

I wanted to be able to use this compact dryer without dealing with tangled cords, adapters or cumbersome power supplies. This portable version of the smaller dryer leverages the innovative 9-volt battery sleeve designed by JimbalNy. ...Most...

I always struggle to fill my hose with water and vinegar for cleaning without getting trapped air in part of the length, so I designed this cap to seal off one end when filling the other. ... Scale up or down in both dimensions if your hose is 22...

I spotted the elbow by jrhaggis and decided I needed one just like it for my project - a HEPA filter adapter that I'll be uploading here (4125993). I prefer to print without supports, so I gave it a redesign. Since I work with PLA and don't have TPU...

A hose coupler for a Mirage Quattro mask. ...

I got tired of putting my mask in a nightstand drawer full of crap. ...With this gizmo the mask hangs neatly on the side of a drawer or shelf.

PrusaSlicer prints with 80% rectangular infill and PLA material will result in a 22mm Cap that leaks between 20-90lpm when PEEP is set to 5-20cmH2O, possibly leading to varied results.

Wall suport to AirSense 10

With hardware (4 m3x8 SHCS) this solution should weigh roughly 13 grams. I designed it with the attributes of polycarbonate in mind. - I have only printed it in polycarbonate - If you print it in another material please let me know how it works...

I couldn't help but play with the design. Size is 29 mm approx. I printed with no raft or supports, and first layer size was .8.........You might need to use a knife or small screw driver to separate the teeth. ... Category: Parts

I always wrestle with getting my hose completely submerged while washing it in vinegar and water, but it inevitably flops around and gets stuck with air pockets, so I designed these clips to keep the hose straight and allow air to escape freely.

Customized version of https://www.thingiverse.com/thing:1571860 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1571860

Customized version of https://www.thingiverse.com/thing:5789087 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5789087

The clips attached to headgear have a tendency to crack at the front edge after multiple uses. When they do fail, it's usually not at an opportune moment, so I took matters into my own hands and decided to create my own instead. To print this, I've...

<p>This is a print for a bracket to mount a hose. ...&nbsp;This is designed specifically for the ResMed Climate Line Air 11 hose but as most hoses are universally sized I'm sure this will work for most.</p><p>I included two prints, one has an inner...

The original was just a little too long to fit in my mask. ...Shaved 0.25mm from the end and then added 0.25mm to the the opposite face to keep the size the same.

Customized version of https://www.thingiverse.com/thing:2974719 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2974719