cover for ender 3 3d models

Modified version of paulhaines screen cover supports: https://www.thingiverse.com/thing:5363536/remixesMade to fit snugly on the ender 3 screen if you have this LCD PCB Cover on: https://www.thingiverse.com/thing:2858209Requires supports. ...Recommend...

Ubgrade display holder ender 3 v2 for small cover to reduce the width of the ender 3v2

This has mods for plastic printing.For the original Creality Ender 3 Extruder Fan Cover design file, see this printable:https://www.printables.com/model/91411-original-ender-3-extruder-fan-coverNeeds supports for the screw hole tabs.If you're doing...

This has mods for plastic printing.For the original Creality Ender 3 Extruder Fan Cover design file, see this printable:https://www.printables.com/model/91411-original-ender-3-extruder-fan-coverNeeds supports for the screw hole tabs.If you're doing...

A nice (or at least, I like it), cover for the creality ender 3 (pro) V1. ...Adds to the aesthetics IMO.

Compatible with "Ender 3 60mm Board Fan Cover": https://www.thingiverse.com/thing:4902986

This is a remix of 'Ender 3 V2 & Pro Silent Motherboard' by scaryPug which is a remix of TerraVestra's design Designed to fit Ender 3 V2, but will fit Ender 3 Pro also. This cover houses 60x25mm fan. This cover adds 15mm, so you'll need to raise...

The thinner design of the Ender 3 Pro PSU compared to the Ender 3 PSU meant that the Noctua fan couldn't effectively extract all the hot air due to its proximity to the PSU board, so I designed a new cover with increased ventilation and more space...

Friction fit fan cover (no extra screws needed!) designed to protect the hot end fan for the Satsana fan duct for Ender 3. It took me a couple of iterations to eliminate amplified fan noise when grills are too close to the fan. You may have to...

Noctua fans I used for the MB and PSU: Noctua NF-A8 FLX (80mm) I printed both parts (MB and PSU cover) in PLA. PS: If you prefer to add a fan cover - here you go: https://www.thingiverse.com/thing:4837562 Btw. ...you also need those feet to lift up...

Use this as a base to remix or glue on an attachment and use the rail as a support structure. ...Designed for the Ender 3 V2

This is a custom cover designed specifically for the Ender 3 Pro, allowing users to install a quiet 60mm Noctua fan in place of the stock jet engine. The Noctua fan has a thicker profile than the original, which necessitates this modified cover. I...

Noctua fans I used for the MB and PSU: Noctua NF-A8 FLX (80mm) There's also a mount built in to fit a LM2596 buck converter (43mm x 21mm) I printed both parts (MB and PSU cover) in PLA. PS: If you prefer to add a fan cover - here you go:...

I love working with quiet noise and the first thing I designed for my Ender3Pro was a brand new power supply cover for an 80mm Noctua fan. In my case, a buck converter isn't really necessary because the power supply already has a 12-volt output;...

I used the Ender 3 model found on Github to design this piece. Measured the rough distance necessary so that the new fan stays a few millimeters away from the heating block. The interior walls of the spacer are at an angle in an attempt to direct...

Next, I carefully placed a hole for a 90-degree Mini USB to USB cable for my Raspberry in a rail mount case on the left side of the Ender Controller. ...This cable is exactly what I needed: ...

I put a hole for a 90 deg Mini USB to USD cable for my Raspberry in a rail mount case on the left side on the Ender Control. ... this is the cable i used: https://www.amazon.ca/gp/product/B004YD6LW0/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 ...

Another remix of this fantastic motherboard cover.Remixed to fit 60x25mm fan and modified/enlarged air vents and walls as well.Included is modified leg to make everything fit. (https://www.thingiverse.com/thing:4603075)Print SettingsPrinter...

I remixed this to fit my Ender 3 v2 PSU and mount it outside of my enclosure, but I ended up not using it because I only had ABS to print at the time and the print failed. If you print this, let me know and show me! ... If you want to have a go at...

... this from scratch in Fusion 360. https://www.thingiverse.com/thing:3670360 Step file included Changes: - Smoothened out every edge for a smooth feel on fingers - Shortened the protruding part to just clear Snap-On's LCD door for that linked cover

This PSU cover increases the depth of the PSU to allow for the installation of a Noctua NF-A6x25. The cover is split into two parts to make it easier to print while still allowing the original bottom panel to fit over the PSU case. I friction...

Use original screws for the cover and 4x M4x15* bolts (no nut required) for the fan. ***BEWARE*** to the length of the M4 bolts! They may touch inside components. It's better to use a bushing or some washer. Or you can print a PETG M4x20 bolt...

The additional space in the new housing is used (optional) for: - LM2596s => Reduce voltage to the fan OR use power for additional LED strip - BBT Relay V1.2 => automatic off after printing - DC/DC 24V - 5V/3A USB => Powering Octopi The Cover is...

Another remix of this fantastic motherboard cover. This time to fit 60x25mm fan and modified/enlarged air vents and walls as well. I also had to modify the leg to make everything fit. ... (https://www.thingiverse.com/thing:4603075)

This system was engineered to streamline the process of routing cables for a high-intensity lighting array.

I added the micro SD extension to give myself a spot for it. Now I can keep everything organized. ...I set it up vertically, making sure the curved side faces upwards.

Should be ok for any Pla print. The fan can be mounted with normal case fan screws from the boardside. The 2 original frontscrews can be used, the backside can be screwed with a profile on the 40 with a profile nut. Cables you want to route to the...

This is a custom cover for the power supply of an Ender 3 printer. If you wish to upgrade to a MeanWell LRS 350 - 24v power supply, or one similar, this design will accommodate your needs. Key benefits of using this cover include: 1. Compatibility...

This cover may also fit on an Ender 3, but you must check that beforehand. Warning: Opening a power supply is extremely hazardous. Do not attempt it unless you are certain of what you're doing. THERE ARE FIVE DIFFERENT OPTIONS: 1: PSU-Cover with...

So, this project is a remix of "Double LCD drawer Ender 3 / Pro " by DaVinci2000 and "Creality Ender 3 Pro - Raspberry Pi 2/3/4 + LCD Enclosure " by eoyilmazI was searching for a enclosure for the back of the LCD with drawers and couldn't find one,...