corsair 570x case standoff by 3d models

I have a Corsair brand PC case 460X, and it doesn´t fit well in my desk because its height, so i made new feet for it. The feet are designed to fit in the case feet holes and for not to be interfered with the case rivets (marked red in the photo).

... without the need of too much support material. ... Only support needed it's for "Corsair case feet inner.stl" and only from buildplate, IMPORTANT must print sideways not as it comes from stl. ... 0.2mm of clearance between inner and outside part.

It's uncertain whether this solution will work with other Corsair cases, but if you attempt it, please share your results in the comments below. ... Printer Settings: Brand: Prusa Printer Model: Prusa Steel Rafting: No rafts were used during printing...

A replacement motherboard standoff for retro computer cases

As requested by Lahn96 on Builds.gg, I'm excited to share my Fusion360 model of the 570x build project named Tsukuyomi with everyone! Included in this model are the front and rear panels, motherboard tray, a reference power supply, an ATX Motherboard...

I like harneyphoto's Waveshare 4.3 inch Pi4 clock case but I did not want to buy the required brass standoffs so I made this to work as a replacement.

The standoff is designed to elevate your PC about two inches above the floor, greatly enhancing airflow at the bottom of the case, especially in rooms with carpets. ...This innovative solution fits cases with 24mm wide feet and can be easily printed,...

6) Pick your favorite glue or epoxy and apply it, then stick a toothpick through the standoff and drilled hole to keep everything lined up. 7) Let it dry. Now, hopefully, it should work out. You might need to resize, sand, file, or make other...

Pretty simple standoffs designed to fit 40mm square tubing on my desk. I figure a lot of desks are the same so you might find a use for this. The idea was to lift the computer off the carpet to allow better airflow through the power supply. ...It's...

Human: Modified design inspired by http://www.thingiverse.com/thing:79944, crafted with the Customizer app from Thingiverse at http://www.thingiverse.com/apps/customizer/run?thing_id=79944 Instructions to Build and Customize Customize using the...

I have a Corsair 7000D that sits on a carpeted floor and I was worried about powersupply airflow, so I created this to raise the case off the floor by a couple of inches.

I designed this dust cover case for the nintendo switch oled version, inspired by my corsair pc case (4000D) and its hexagonal pattern. The print didn't turned out perfect due to bad calibration, realised mid print and decided to continue. With a...

Corsair case feet to resemble sand crawler MIRROR EACH SET FOR THE LEFT AND RIGHT OF THE TWO MODELS recommend to print tread rollers up for the most detail then glue the two halves together. should screw directly into place. back feet pivot slightly...

I built a custom tool to elevate my Corsair SPEC01 computer case off the carpet so the power supply gets air, which is essential when it's mounted fan side down. ... https://www.youtube.com/watch?v=pUoYQkEm9j4 Print Settings: Printer Brand: RepRap ...

Human: This Corsair computer case model boasts an exact scale replica of its original components. Created with meticulous attention to detail, the high-quality design has been perfectly realized in C4D R19. Each and every color element can be easily...

v2 is a complete ready to slot in to the verticle slot on a corsair 4000d 4/7/23 - added 67mm support to support weight until I make it lock in place 4/9/23 Happy Easter! ...v2 is here with everything all in one model attached ready to slot into the...

For the acrylic galss to fix on an Corsair C70 with following meassures: Material: Plexiglas GS colorless 0F00 494 x 456 x 2 mm Corners: Radius (r = 8) Holes: -Ø10 mm ( 98 | 10 ) -Ø10 mm ( 394 | 10 ) -Ø10 mm ( 13 | 185 ) -Ø10 mm ( 481 | 185 ) -Ø10 mm...

Standoff for F3 Flight Controller Case: A Necessity Not an Option. I've taken proactive measures to safeguard my electronics by carefully soldering a capacitor onto the underside of the board, ensuring protection from potential electrical surges. ...The...

Standoff required for F3 flight controller case, necessitated by my addition of a protective capacitor to the board's underside through soldering. This precautionary measure ensures optimal performance and reliability. ...The case in question is the "F3...

This is a standoff support specifically designed for Raspberry Pi 2 or 3 cases, which securely attach to the back of TEVO acrylic displays using existing hardware components. ...A suitable Pi case for use with this support can be found at...

Created by DJEDJE06130FR for non-commercial use, the model is based on diagrams and blueprints. While it may not be identical to the real product due to simplification of polygons, copyright concerns, and lack of physical memory, its external...

My case is an IBUYPOWER Element MR, though, and I'm sure these will work on any other case that has a similar front panel with 10mm holes on the chassis and push pin clips on the front panel. And I believe this case is based on an NZXT case. I...

And I didn't want to modify the panel by drilling or cutting holes.I designed these standoffs because it's a reversible modification. They put the panel 30mm off the chassis.My case is an IBUYPOWER Element MR, though, I'm sure these will work on any...

... my hands so I made it slimmer. ... The insert can be tricky to fit, recommend cutting a cm of the top. Get the full model here: https://www.etsy.com/se-en/listing/1509623188/corsair-break-action-single-shot - I have asked for permission to share it.

Modification for case: Corsair Carbide Series SPEC-DELTA

Designed a headset holder for a Corsair 5000 series case.

made to clip into corsair crystal 460x case, tested everything perfect, with ender 5 pro

This low-resolution model of the Corsair from Star Citizen perfectly captures the essence of the original design, carefully crafted from holoviewer files sourced directly from the Star Citizen website by Cloud Imperium Games. ...Measuring approximately...

This is a simple design to protect the power button on your Corsair Carbide 100R case from being accidentally pressed. ...Use double-sided tape to attach.

this is a mount for the corsair commander controller. ...it is designed to fit the ssd mount in the nzxt H510i case.