corsair 4000d front panel replacement 3d models

Decided I wanted to make my own woodgrain front panel for my Corsair 4000D, in the spirit of the Fractal North. I've included the CAD file as well so you can make whatever changes you want and adapt your own front panel design. Might need to rotate...

I ordered a non-Airflow 4000d PC case in hopes I could buy an airflow panel in the future. Unfortunately they have been out of stock for awhile now so I decided to design my own. In an improvement over the stock panel, I wanted to make it easier to...

I wanted more airflow for my front fans, so I have tried to order the AIRFLOW front panel available for 4000D series cases direct from Corsair but: 1) they seem to be permanently out of stock and 2) they don't ship outside the US even if they were...

Custom Elite Dangerous version of my Corsair iCUE 4000X Front Panel design showing the 3 base Elite badges, Combat, Exploration and Trading (from top to bottom) This will fit the Corsair iCUE 4000X & 4000D cases as they are the same chassis. If...

Custom Elite Dangerous version of my [Corsair iCUE 4000X Front Panel design](https://www.thingiverse.com/thing:4889085) showing the 3 base Elite badges, Combat, Exploration and Trading (from top to bottom) This will fit the Corsair iCUE 4000X &...

Replacement side panel mount, for Corsair 4000D case. Will replace the stock, ball mount. This is a copy of the original, no modification have been made. Print with PTEG at 100 infill and 0.15 layer hight. ...

Designed a new front panel for my Corsiar computer case to improve airflow. My CPU (Ryzen 5 3600) and GPU (AMD RX480) each run about 10 F degrees cooler and the blower style GPU is runs much more quietly. It is designed to be printed in 3 pieces...

Designed a new front panel for my Corsiar computer case to improve airflow. My CPU (Ryzen 5 3600) and GPU (AMD RX480) each run about 10 F degrees cooler and the blower style GPU is runs much more quietly.</p> <p>It is designed to be printed in 3...

Tray to mount extra single ssd in front as well as the back of corsair 4000d case

With certain fans placed in the new Corsair 4000D cases (I have the airflow and have Noctua NF-P12 redux-1700 fans, but I assume it happens with the non-airflow as well), sometimes the front mesh panel can contact the center fan's centerpiece and...

If you don't use a radiator in your case, the shroud has a pretty big gap. ...This piece will fill that gap. Will fit the Corsair 4000D case, with a 120/140mm fan installed.

I always wanted a honeycomb pattern on my front panel, but by the time I got a new case I couldn't find any models with one. Then I got a 3D printer. Instructions: 1. Set top & bottom layers to 0 2. Set a decent number of walls (3 was fine in my...

I always wanted a honeycomb pattern on my front panel, but by the time I got a new case I couldn't find any models with one. Then I got a 3D printer. Instructions: Set top & bottom layers to 0 Set a decent number of walls (3 was fine in my case)...

I have OCD for the Corsair 4000D. So I made a cover plate to cover the big hole for the radiator. The slot in the front is for a 20 x 2 x 5 magnet if you so desire. ...Print instructionsI used the Prusament PETG signal white at 240-250 and bed at 85 -...

CORSAIR 4000D Motherboard Accessory Tray for install ICUE Commander PRO, Commander CORE, RGB Fan LED Hub or another of any brand

These are covers for the rear of the corsair 4000D. I created them to prevent outside light from entering the case. There are two models. One is for the replacement pcie covers and one is for the mesh above the fan. Note, that you will only be able...

v2 is a complete ready to slot in to the verticle slot on a corsair 4000d 4/7/23 - added 67mm support to support weight until I make it lock in place 4/9/23 Happy Easter! ...v2 is here with everything all in one model attached ready to slot into the...

Corsair 5000D/X Front Top panel

vibration dampers for the front panel of the corsair 275R, under certain conditions it vibrated in low frequencies, adding these fixed the issue for me. They print out quickly, and you can fill them with anything heavy, I used plaster. ... Used a 0.4mm...

Replacement door clip for Corsair Obsidian 450D/750D/900D cases. Remove the original from behind the plastic front bezel. This part just fits in the existing hole. It clips on the door with enough force to be able to pry it off with your fingers. ...

Hello, Following a defect of my panel of fixing of face. A fixing lug was broken. I drew and printed the fixing tab in order to repair it. ... Sincerely

Cover plate for the Corsair iCUE 4000X / 4000D / 4000D Airflow cases. It is literally a slab of plastic but it does the job for hiding the cables. Measurement in case you want to use the Ai file or SVG File as a template: X: 158mm Y:...

This allows you to mount an additional 3.5" hard drive in your Corsair 4000D on the surface above the power supply using readily available tool-less hard drive rails (make sure you still have adequate airflow and cooling). It can also be used to...

I made a bracket that bolts to an SSD slot to hold the RGB hub in my Corsair 4000D case instead of shoving it in the basement like all sane people do

Supports a card inserted into the vertical riser slots on the Corsair 4000D. The holes are aligned for the front vertical slot and a LINKUP - Ultra PCIe 4.0 X16 Riser Cable. ...There's a mounting hole that will get attached to the case to keep the...

Summary: Wifi antenna mount for Corsair 4000D Airflow with minimal design hidden from sight and minimal space required. Mounting: Refer to the pictures for mounting location. The antenna will slide into bracket similar to the OEM and will be held...

You can mount the intake with the extra hardware provided by corsair with the case. 2 fan screws and 1 ssd plate mount screw (2nd smallest screw in the bag). The fan must be in the bottom most position for the intake to fit, all the way to the floor....

One of mine UPS hit the ground and broke front panel. I decided to prepare replacement. If you own that kind of UPS you should be interested.</p> <p>You may choose to print version with or without our logo. ...Enjoy!</p> <h3>Print...

Tronxy Prusa i3 printer owners quickly find that installing a new front panel is essential for repairing their machine on a sturdy base plate.

One of my UPS units crashed to the floor and shattered its front panel. I have made up my mind to build a brand new one. If you possess this type of UPS, you definitely will want to know about it.\r\n\r\nYou can opt for a printed version with or...