corsair 280x vertical gpu 3d models

The caps come off of the nozzles fairly easily if you lift from the bottom of the cap in a bit of a vertical twisting motion. Print them open end up. You will need cut three PVC tubes to the appropriate length to hold the filament spools. I found...

These terminals are rectangular rather than square, so you need to rotate them to put the two little screwholes vertically rather than horizontally or they won't fit.Now strip the ends of the wires. Solder the negative (spring terminal) wires to the...

Also, a brim is essential to help ensure it remains attached to the build plate for the duration of the print as you want it to print vertically, with the pocket on top. The highest stress I assumed for the lifetime of the handle is the hoop stress...

Two offset LED assemblies within the fixture allow this explosion proof linear lamp to provide a brilliant 100° horizontal beam spread and 140° vertical beam spread while achieving a 10,800 lumen output to maintain a small form factor. The LED...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

To help reduce stringing, print the top and bottom pieces separately in a vertical orientation.In order to give this some heft (and because my print bed would not fit the entire wand in a single piece) the split model has a stiffener slot for for a...

I printed on the textured sheet by Prusa and didn't need any brim.Activate “detect thin walls” in PrusaSlicer and make sure that the thin verticals support layer is sliced correctly (see picture) ASSEMBLYDisassemble one KLAMBY. You only need the...

That's why walls are mostly vertical, there are no overhangs, no supports needed, no subtle curves that would show layer lines , these will look the same with a standard .4 nozzle as they look with a .6 (given the same layer height) and be done...

They will stay where they are supposed to once everything is slotted in together.When I store the boxes Vertically, I place the Cards in the Base Game box and the Small Minis in the Monster box on the bottom. It just helps those components stay in...

 Print 2 x 70mm and 1 x 31 mm.Aligned vertically on the plate they will take ages but it'll save you having to source tubing or rods of 6.23 mm diameter.***********************************************************4 x rubber bands about 32 mm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Two offset LED assemblies within the fixture allow this explosion proof linear lamp to provide a brilliant 100° horizontal beam spread and 140° vertical beam spread while achieving a 5,400 lumen output to maintain a small form factor. The LED...

At full power the glider climbs almost vertically. Some attention should be paid to the coloring on the underside of the wing. As a pure thermal glider, visibility of the model at higher altitudes becomes important so as not to lose sight of it. ...

Also, a new vertical slot was created on one of the base's walls, to provide support to the side plates throughout its whole height.The former change should provide a stronger friction fit between the pieces, and the latter change should...

If it needs broken free place the "Main Body Pieces.stl" vertically with the print bed side on the bottom. Place it on a table and slide the slider off the edge of the table and tap the slider with something round and flat to break it free. The...

two 21x16 cm plates (vertical sides), and one front plate which is 52(w) x 30(h) and has a square hole cut in about 2cm from the edge. I also fixed a smaller piece to the top of teh frame to hold the electronics. The frame, when assembled, required...

The lamp can be easily adjusted vertically and locked into position.LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation and/or transportation. Instead of...

http://www.thingiverse.com/apps/customizer/run?thing_id=41274 Instructions Using the following options: pillar_translating_position_x_y_z = [00_pill_location_x,00_pill_location_y,00_pill_location_z] 00_pill_length_now_is = 2.5...

The back section has vents on the bottom - set up your slicer to print them as bridges (horizontal and vertical lines, not diagonal) and they will look like awesome vents when done (In Cura, you can do this by going into the Experimental settings and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

When reinstalling your lead screw, I've found that adding a 4mm ball bearing to sit between the lead screw and motor shaft does an amazing job with flexible couplers in stopping vertical compression and wobble issues. ...Check out this video for more...

In reality the handrails are all in the same plane, but that would make it an absolute pig to solder, so the jigs are set up to solder the second horizontal bar behind the vertical bars. To be honest, I have no idea how well a printed jig will work,...

On the left, one grub screw is vertical while the other is orientated towards the front.When the alignment is all good, use a bit of Medium Thread Lock and tighten the grub screws.Thread the belts through the rear brackets while access is still easy....

The main tradeoff, then, would be balancing how far to mount the wires from center on the uprights, because too far out would mean giving the anchors a big moment arm to translate the uprights' deviations from vertical into twisting forces on the...

Once the upside-down table top has all four corner assemblies bolted on, you should be able to attach not only the four vertical table legs, but also the four legs that get inserted horizontally (to gain the extra headroom needed for a B1). I...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

Orient the tee so that the two inline holes are vertical, the middle leg points to the left, and the curve of the middle leg goes from left to down. The vacuum will attach to the bottom (leg 1), the waste gate bottom and cover will be inserted into...

This is all done first, while the top of the enclosure in face down on your assembly area. Once the upside-down table top has all four corner assemblies bolted on, you should be able to attach not only the four vertical table legs, but also the four...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...