corsair 280x vertical gpu 3d models

The Wingtips and the Vertical stabilizers can have their bottom bits printed at .25mm layer heights, but they will look better if you switch to .1mm layer height for the tops of them. To aid in bed adhesion and add additional strength, I like to...

For stacking the tiles vertically, I experienced a very tight fit at first. However, it quickly worked loose with use and fits much better now. Circular Number Tokens Print one Round2 tile, one Round12 tile, and two of each of the others. I...

Hardware ------------- Linear Rails: • (24) M3x10mm socket cap screws • (24) M3 t-nuts X-Carriage Mount: • (4) M5x20mm socket cap screws • (4) M5 nuts • (2) M5 washers (reuse existing) X-Carriage Linear Rail Block: • (4) M3x10mm socket cap screws...

Attach the leftmost point of the arc to the right-most point of the arc preceding it.Eyes: add construction geometry off the top ~2.9cm~Draw circle Z on the construction line with proper dimensionsMirror circle Z onto the other side to make circle...

Because I only have FDM printers I needed to build this vertical to keep it smooth and avoid having complicated and hard to remove support structure in the printing. I ended up creating an X or cross-shaped detail in the middle of the sleeve to keep...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

I have given extra tolerance around vertical layers above the magnets to compensate for a lower roof where the magnets would go. it works great during my testing. This was designed with a printer that was calibrated using Cura's Horizontal Expansion...

At full power the glider climbs almost vertically. Some attention should be paid to the coloring on the underside of the wing. As a pure thermal glider, visibility of the model at higher altitudes becomes important so as not to lose sight of it. The...

A bed that is not square with the frame prints parallelograms in the Z-axis vertical plane, not rectangles with 90 degree corners. For that reason, I have created a probe extension and coupler that allows you to perfectly square your bed with your...

While I could have left the base as-is, I elected to cut the vertical bars on the base down so as to lower the OTA on the base. ... Extrusion Cuts OTA (4) 921mm rocker board (2) 303.5mm (2) 283.5mm (2) 180.5mm (1) 381mm ground board (2)...

Two offset LED assemblies within the fixture allow this explosion proof linear lamp to provide a brilliant 100° horizontal beam spread and 140° vertical beam spread while achieving a 10,800 lumen output to maintain a small form factor. The LED...

Sizes for even-sided n-gons are measured by the distance “from flat to flat” (apothem x 2), whilst for the odd-sided n-gons are measured by their greatest width (and thus protrude from the facing vertex, whilst even-sided protrude from the flank...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 7 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

I then soldered the 5V output wires onto the rear of the Raspberry Pi board to J8's pins 2 and 6 (see attached photos and diagams). The lid part has a slot in it, allowing the flat cable of the Raspberry Pi webcam to be fed in and folded at 45degree...

In addition, I decided to print the figure in life size, which meant not only enlarging everything, but also cutting out the legs, which did not fit vertically in my printer after enlarging. My printing space allowed without cutting other parts to be...

(I use the left and right walls to sort of hold the center wall in place vertically while it sets. 8. Glue the left and right walls to the floor and center wall. (The right wall has a hole for the cord). 9. Glue the back wall to the floor,...

I printed everything in the vertical orientation, except the pommel, and the handle base b, which was printed upside-down. this was dont to preserve the visible surface details and to avoid putting supports on the parts that screw together. use the...

This mounting component extends the fixture up to 6" from a flat, vertical mounting surface. Spacing between the mounting component and LED fixture's fins, which are located at the back of the unit, streamline cool operation. This wall-mounting...

It follows the same principles as the original dial gauge holder but also uses the screw head of one of the fan screws to vertically stabilize the mount.Additional materials required:1x M3x20 screw for icarus holder (can be a little bit more or less...

See section “Storage” below.April 11 2021:Added a third layout “vertical” for the plant tags (see photos)The STL files for tags now also contain the correct number of trays.Added links to my other related designs at the end of the...

All right reserved // web: http://www.RinkyDinkElectronics.com/ // // A quick demo of how to use my DS3231-library to // quickly send time and date information over a serial link // // To use the hardware I2C (TWI) interface of the Arduino you must...

When sawing out, one cut horizontally and one vertically are sufficient, these are inevitably somewhat slanted, the component is adapted accordingly. Towards the optical fiber, the old plastic parts are slightly fused, the whole thing can be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Uploaded Size 18.4 Download size 25MB Geometry Triangles 80.5k Quads 306 Total triangles 81.2k Vertices 40.9k PBR No Textures 1 Materials 1 UV Layers Yes Vertex colors No Animations 0 Rigged geometries No Morph geometries 0 Scale transformations No...

Like… very-nearly-the-whole-MK3s-build-plate-big, so don't be surprisedSettings (how I printed mine, at least):Prusa Slate Silver PETG0.4mm nozzle.2 layer height20% infill (resulted in some surface scarring, but it's not visible on mine when in...

All parts print without supports.AssemblyIn addition to the 3D printed parts, you will need:12 - airsoft BBs (or any other 6mm diameter metal or plastic balls) 5 - 6-32 x ½" socket cap screws (or M4 x 12mm long)4 - 6-32 nuts (or M4)Then proceed...

This mounting component extends the fixture up to 6" from a flat, vertical mounting surface. Spacing between the mounting component and LED fixture's fins, which are located at the back of the unit, streamline cool operation. This wall-mounting...

If mounting trays to the wall as well I would advise using the “Wall to Tray” Pieces to support the trays properly.Shelf Widths: 2in, 3in, 4in, 5in, 6inShelf Lengths: Short = 2in, Medium = 3in, Long = 4in or 5in, Extra Long = 6inFillers: 1x1in,...

See also http://youtu.be/7F2fIF9PNBk for a short demo video of the original version. To store a coin, you may release a coin from the rightmost top, and it will slide down the hill and go into the appropriate tube. Once a tube is full, remove the...