coroplast cutter 3d models

I wanted a Coroplast cutter, The professional ones are great, I don't use one enough to order one. I do have plenty of box cutter blades. I tried to set it up so the blade cuts as close to the edge as possible. I will start with the blade holder: ...

This tool combines a standard single-edge razor blade with a Coroplast sheet for rapid and safe slicing in the extrusion flute. It was created specifically for use in my heat recovery ventilator project on...

Super useful tool, but the RSDOC files meant that I needed to install DesignSpark, which is Windows-only. For users that might be on Mac or Linux, I figured it might be helpful to upload the STLs. ...I printed these parts at 0.12mm myself; a tight fit...

I crafted a DIY project that enables users to create their own storage bins from coroplast sheets. ...This innovative design is still under development, and future updates will include additional size options for maximum versatility.

A simple screw together connector for corrugated plastic (coroplast) for use in things like small animal cage liners. Long enough to secure two layers of standard weight coroplast. Easily screws and unscrews by hand. Because there's no flex in...

Coroplast 90 deg holder for smaller corrugated coroplast. I use these to hold the coroplast in place and glue a decorative piece on top or bottom for structure. I print in PTEG but any filament will work as these are only to hold in place until...

Building something with coroplast? These corner (and related Edge) brackets worked great for me to build nice, solid enclosures. ... [Edge Brackets: https://www.thingiverse.com/thing:5284272]

I designed this latch specifically for my Coroplast box used for delivering food orders on my trusty scooter, the Honda PCX. The goal was to create a fast and seamless locking and unlocking mechanism. ...It's just a rough sketch, but a solid proof of...

This is a joint that I designed to hang coroplast squares for a stage design. The loop on the back is designed to slide snugly onto pvc pipe that is 21.6mm in diameter. ...The holes are sized for m6 bolts ( I bought white nylon ones on amazon).

I was building an enclosure for my Ortur LaserMaster laser engraver and needed a set of brackets to hold the coroplast together. There were some on Thingiverse, but some were too thin, some didn't fit well, etc, so I made yet another version. These...

After all my other coroplast panels were assembled with my designed brackets, I found the lid was sagging. I built an interlocking edge support that could span across the lid and is supporting the drooping edge fairly well. I was limited by print...

... this guide. Simply place it against the edge of coroplast, secure with duct tape on both ends, and utilize an exacto knife instead of the conventional vinyl cutter. ...For optimal results, use the thinnest blade available to navigate around corners.

If your Nano Drone crashes or lands harshly, damaging the Coroplast's holes, print out this design to reinforce the hatch and support the fractured areas.

If you have ripped the holes in the Nano Drak Coroplast after a crash / hard landing like I have then print this to cover the top part of the hatch and support the holes.

I made these to go along with a colorplast clip set to build a coroplast enclosure. ...I glued in a magnet to allow for a door that is held closed or open with magnets.

For cutting coroplast sheets, acquire two 4x8ft x 4mm Coroplast corrugated plastic from Home Depot (available online), with a minimum order of ten sheets at $11 each. Note that the design for the heat exchanger remains unfinished and untested, so...

Humans were designed to function as organizational tools, streamlining complex tasks and creating order from chaos.

My neighborhood coffeehouse needed to display some signs, so I created and produced a custom-made pressure-fit hook that allowed them to easily hang 4mm coroplast signs using magnetic hooks attached to the ceiling.

Two arcs create removable doors made mostly from 4mm coroplast. Neodymium magnets are pushed down flutes to affix doors to frames. The bottom arc has a hook profiled to plastic base of Overlord Pro and Overlord. Parts work as is, but improvements...

A versatile 90-degree connector perfect for corrugated plastic sheets. ...Ideal for crafting printer cases and photo display lights.

Different style of coroplast edge clip that allows for embedding of magnets to hold door closed or open.

cutter

Cutter

Cutter

cutter

cutter

Christmas Cutter

knife, cutter

grass cutter

A Cutter