corexy ender 5 plus 3d models

Just needed a measuring stick holder for my Ender 5 Pro. The hole is 20mm x 6mm. Should fit for the most types and fits very tight on the 20mm side of the profile. ... I add the Fusion360 file as well.

Just needed a measuring stick holder for my Ender 5 Pro. The hole is 20mm x 6mm. Should fit for the most types and fits very tight on the 20mm side of the profile. ... I add the Fusion360 file as well.

Due to the Ender 5 Plus's independent Z screws, they can easily get out of sync, making it a challenge to maintain proper alignment. Removing any part can cause the bed to fall and become misaligned. If you're like me and don't run auto-bed leveling...

---------------------------------------------------- This is my design for a kinematic self levelling bed system for the Ender 5 plus. This design allows you to fully automate the levelling of your bed to a very high precision - meaning you only...

ebder 5 plus microswiss mount setup. 3 screws mounting. you need 2xm4x60 2m20x4 and one screw and nut from an original roller wheel. this braket is used to be mounted under the cariage. each exoslide on the y axe must be mounted as shown...

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus.NotesRecommended parts have “rev4” present (except for the buttons).  Alternatve parts (refer to “Earlier Revision Options” above) have "rev2" or "rev3"...

This is a complete overhaul of the ender 5 plus's gantry. After trying the Merc One core-xy mod, I found that the belts were far too long to prevent ringing, and the belt path too complex to avoid problems. Also, the stock belt arrangement really...

I needed led strip holder for my Ender printer.

I tried using the original design on my Ender 5+, but unfortunately, the tabs for the screws were slightly too thick. Printing it with resin proved to be a challenge as well - the logo required extensive support structures, which made the process...

... for heavy and expensive devices. Use an M4 x 25mm (or longer) screw and nut to mount it to the cornerpiece of your Ender 5 rack. For your camera, simply add the right screw (e.g., check this one: https://www.thingiverse.com/thing:595837). ...

So I started Freecad and adapted the template to my needs. This is a combination of the Parts from paydayxray (https://www.thingiverse.com/thing:4310609) and Andrea_Botti (https://www.thingiverse.com/thing:4710174) Ich wollte einen...

You may think that it's not Ender 5+ any more, but almost everything from the original kit is reused with minimal adjustments.That was the design intention:- no hassle with electronics: 100% ender5+- sturdy frame: I use locally available "Kombi...

This is a linear rail mod for the Ender 5 Plus. It encompasses the XY&amp;Z axis. I designed these parts because I was unhappy with most other mod variations of them.</p><p>Z Axis - The Z axis part were designed using the BLV MGN Cube as a starting...

This is a Creality Ender 5 Hot Bed Cable Relief that I Remixed in TinkerCAD. I took the zip tie design and designed an attachment around it. The reason I designed it is because a lot of the other designs took way too long to print and took extra...

Just added a side car for the BL touch since I imagine that most people have the BL touch as it came stock with the ender 5+. I printed the adapter in PLA, but you may want to go with PETG as it sits really close to the hot end, so we'll see how...

Prolunga per sensore filo di crality ender 5 plus.

Plate to mount a Biqu H2 to the Ender 5+ Old nozzle to New Pictured above Nozzle to Probe -33,-11, Z should be same as stock mounts using 2 M3 x 8mm botls for the H2 and 2 M3x 8mm bolts (may want use a washer) and 2 m3 nuts for the Bl touch Bracket.

This is a linear rail conversion for the Ender 5 Plus. It encompasses the XY&Z axis. I designed these parts because I was unhappy with most other mod variations of them. <b>Z Axis -</b> The Z axis parts were designed using the BLV MGN Cube as a...

This will help with that. This spacer is long enough that the stock Ender 5 + hotend will not be able to touch the bed when you tighten the z axis, so no fear of it crashing. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't...

... you were homing your z axis then you need to re-level your bed carriage. This will help with that. This spacer is long enough that the stock Ender 5 + hotend will not be able to touch the bed when you tighten the z axis, so no fear of it crashing.

The original part designed be Xerber https://www.thingiverse.com/thing:4727217 did not work with my Ender 5+, my Z rails are an extruded aluminum design and have an extra bit on the edge, instead of the flat bars pictured on the original design. ...

Dual Gear Extruder: This design was specifically developed for: https://www.amazon.com/WINSINN-Extruder-Creality-Upgraded-Aluminum/dp/B07SY745CF/ref=sr_1_2?dchild=1&keywords=dual+gear+extruder+ender+5&qid=1590272315&sr=8-2 This mount securely...

Also, I don't know if this would work on the normal ender 5. I don't have one so I can't test it, but it should fit so maybe. Parts list: 2x 60T-20T closed loop GT2 belt and pullies, 5mm bore 2x 20T GT2 Pully, 5mm bore 6x 20T GT2 Pully idlers,...

... If you like my Design please give me a like or a make. Thank you Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0,12 Infill: 99 Filament: CR-3D PLA Gold Category: 3D Printer Parts

Filament runout sensor required a spacer to retain usability with a dual gear extruder. ... This spacer uses the 4 original screws, plus an additional 4 M3x6 screws through the back side.

... a smaller version to fit the right-front corner and the back-center. A M3-.50 nut is required. -------------------- front fan 4010 ender5 plus default fan 4010 fan grill right 5015 blower fan ender5 plus mod fix 2021-09-23 add all in one hotend

First time doing something like this, and there's still some unnecessary artifacts from my quick hob-job. Print Settings Printer Brand: Creality Printer: Ender 5Rafts: No Supports: NoResolution: .2 Infill: 100 Filament: [...

I upgraded my E5 Plus to a SKR Mini E3 V2.0 and the Bigtreetech TFT V3.0. I printed this: https://www.thingiverse.com/thing:4421077, but the screw holes of the PCB didn't align, so I remixed it with M3 threaded holes, shifted 1mm from the place...

Not sure what would be needed to get it to work with the stock Ender 5 + display The advantage of this is a slightly cleaner setup as the plate and red adapter Micro Swiss provides to attach the PTFE tubing are eliminated. This sensor detects if the...

This is for mounting a BigTreeTech TFT35 E3 V3 (originally designed for Ender 3) with cutouts for SD card and USB port. Hardware Needed: 4 x M3x8 screws 2 x 4mm T-nuts with 2 x 4x8 screws When printing, take a 2.5mm drill bit and drill the four...