cord pulls for blinds 3d models

For some reason It got modeled at only a 10th of the size so you need to resize to 1000%

... stand. ... The power cord goes through the center of the stand and out the back to help with cord placement. I printed it on its side with tree supports for the cord openings. ... I used a .6 nozzle to print using Tinmorry Silk PLA Orange/Blue/Green.

This is a valance clip with .5 inch extension so you can install your valance over the SwitchBot Blind Tilt. ... When you load the file in your 3d printer software, make sure the size of the object is 26.89mm on the X .

This is a new design for grab the power cord for Apple Macbook. This was design for keep safe the cord avoiding bending at right angles. It add the feature of being able to wind both the usb cable and the power cable. ...It allows wide twists that...

Then slide the end of the cord into one of the slots for storage. If the cord is too thick, the tab can be bent slightly. When it is time to use the Power Supply, unwrap as much cord as needed using the slots to hold the correct amount of slack. ...

I needed a small spool to store the rubber cord for my FiBo filament boxes (https://www.thingiverse.com/thing:4702315). So, here it is. inner diameter: 3cm outer diameter: 7cm should carry at least 30 meters of cord. ...on the image, there are 10...

An electrical cord wall-mounting clip for easy installation; a practical addition to any setup. Despite searching, I couldn't find a suitable option compatible with drywall anchors. Hence, I designed this one. Personalize the OpenSCAD file by...

I designed this because the aftermarket metal extruder does not have a cord holder. I've included the Blender file and the STL. This thing is 4 pieces, two halves to the shell and two clamps top and bottom to hold it together. ... Because its two...

I designed this straightforward template as an alternative to drilling holes for mounting an extension cord. You can use it to secure the cord to walls or desktops without having to drive screws. ... If you appreciate this concept, kindly show your...

To replace the pulls on some blinds. The profile lets you see if it matches yours. ... If you wish to modify, the model is available on TINKERCAD: https://www.tinkercad.com/things/lReAYyKe9sE#/

This is a replacement dial cord wheel for the ASA-1147 vintage tube-receiver I'm currently restoring.I'm sure this model will get a lot of downloads and makes, haha!

Designed in Inventor, used to hold excess cords for the Speedcom communicator when used between cars for HPDE motorsports instructors. The system is great but the cords are not designed to be portable I am including a shallow cord reel version (in...

The stock one that came with my Snow Joe snowblower is too small for a 12 gauge extension cord, and it arrived broken anyway. This design works the same way but is made for larger cords. I upgraded its structure to make it more robust after breaking...

This is designed for a 4" diameter rocket and 3/8" wide shock cord, although it will work down to 2" and up to about 1/2" wide shock cord. I've included .stl files for that size if you don't want to mess with the customizer. I haven't tested this...

... have experienced with the model.NOTE: There are multiple extension cord models sharing the same name. This clamp is specifically designed for the extension cord with item numbers 902.808.26 / 204.642.54. ...It's unlikely to fit any other model.

Designed this as a simple replacement for the supplied retainer as I had little room. 

Attach two tiny finishing nails to your wall or window frame and you're good to go. ...No need for any overhanging parts. ...The dimensions are roughly 2 inches by .4 inches by .2 inches.

Printed in vibrant white ABS plus plastic, it has the ability to produce a wide range of colors and designs. ...The user may choose to utilize a slightly higher temperature filament for printing near windows due to potential exposure to direct sunlight.

This is a fully parametric model (in Autodesk Fusion 360) for a hook to support a power extension cord - mostly for outdoor applications (e.g. to thread an extension cord along your fence, or wall). Designed for standard drywall screws, can be...

... ear straps. ... The design was specifically for an elastic strap 5mm x 2mm. This is just a simple design that allows a cord to slide up or down for tightening, but does not require a spring snap. ... Needs to be in flexible filament for best results.

... if you try it out on a different one, please share your model number in the comments below. Check out the Post-Printing section for step-by-step pics showing how to remove the broken cord holder and install the new one after printing this design.

Holder for an extension cable that screws onto the IKEA LACK. ...Designed for https://www.alza.cz/oem-kf-fb-03-d6128122.htm.Extension cord dimensions lenght 53mm, width 39mm, height doesn't matter.

This device fits tightly onto the droplight cord to stop the cord from retracting. In my case, my droplight has failed and will no longer stop itself. ... This ball prevents the cord from retracting.

This is a quick model (source code included in openScad) for a nozzle attachment that fits a popular Conair 1875 Cord-Keeper hair blower. I printed this in ABS because of its high temperature properties on a Voron Zero. ...Not recommended to print in...

A compact, easy-to-use cord grip designed to fit snugly around 12AWG wire securely. It features 3x10mm screws that firmly close the grip. Crafted for M5 mounting bolts, this device ensures a reliable hold. Print with support on build sheet. ...Thanks...

This handy device ensures that extension cords stay securely connected at all times.

... for elastic straps that are 5mm x 2mm thick. This simple design allows a cord to slide up or down for tightening, without the need for a spring-loaded snap. ...To achieve the best results, this feature should be made from flexible filament.

This is a new design for grab the power cord for Apple Macbook. This was design for keep safe the cord avoiding bending at right angles. It add the feature of being able to wind both the usb cable and the power cable. ...It allows wide twists that...

by Segasonicfan Designs https://segasonicfan.wixsite.com/retro @SegasonicfanDesigns on youtube: https://www.youtube.com/@SegasonicfanDesigns -- simple cover for the bright LED on my GFCI extension cord. ... Best to print with support for the top 100%...

Here's a Replacement Solution: Three-Dimensional Print Designs for a New One. The Main Mount and Cable Protector Are Separated into Two Distinct Parts - A Half-Shell Design. The 3D-Printed Main Mount Is Assembled Using Four Micro Stainless Steel...