cope and drag 3d models

Designed from scratch is a Sunoco Hood Scoop to suit drag cars, hollowed under side for engine clearance and flat bottom to shape to your hood. High in detail, ideal for scale modeling (currently in 1/24 and 1/25 scale). Perfect for those drag...

These are three attachment fittings for to add drag chains to many Atomstack laser engravers such as the X20 Pro, S20 Pro, A20, Pro and I think A7 and any laser engravers with the same stepper motor mounts. These are designed to work with the drag...

i made this to connect drag chain i found on thingiverse to my printer cr-10 v2 profile without using screws or insets but it can connect any 40mm rail anyway holes are prepared for those who want to use them but it is very strong no need for any...

Designed from scratch is a Comp 7 drag racing front wheel, high in detail, ideal for scale modeling (currently in 1/24 and 1/25 scale). Perfect for those drag racing builds! Designed as a 1 piece for faster printing, details include a spindle...

https://www.aliexpress.com/item/32757260673.html?spm=a2g0s.9042311.0.0.20614c4doIw4cPContains JN5.5B link, JN5.5B-XJT-N and JN5.5B-XJT-W mount end parts.This is 5x5mm cable drag chain I drew for mini 3D printer design.If you want a printer-friendly...

This is an alternative top nut for Laisch's CNC drag knife holder for cheap drag knifes. It mounts directly to an ER11 spindle nose, interfacing with the M14x0.75mm thread and collet taper to give reasonable rigidity. It's also slightly lower profile...

Liyu Style Drag Knife Cap for Mostly Printed CNC Print this Liyu style drag knife cap, designed by Allted on Thingiverse (https://www.thingiverse.com/thing:724999). It fits snugly to shield the blade from chipping or accidental cuts. I encountered...

This drag chain contains the z-axis wires, endstop, and could also have your router/laser/probe wires if you want to.This drag chain rests on a narrow aluminum extrusion (15x10mm) which is mounted to truck_clamp_c_primo_raised.stl and...

Drag chain rail mount for MPCNC with Nema 23. ...

A lock-less design of Cable/Wire Carrier Drag Chain

Centerline Auto Drag Wheel (16 x 7-inch)

Drag Chain (15x40) male connector with M3 holes.

The *drag chain will slide on the "roof"* and therefore maintain its clearance as long as it sits on the "roof". So there will remain a (much) shorter part of the drag chain that is unsupported till it reaches its mount at the printhead, thus...

The drag chain will slide on the "roof" and therefore maintain its clearance as long as it sits on the "roof". So there will remain a (much) shorter part of the drag chain that is unsupported till it reaches its mount at the printhead, thus bending...

This Build Requires Some Bolts And Nuts (T-Hammer And M3) For Attachment. "Drag Cable - Bed Connector V07" Attaches To The Bed By Using A T-Hammer Nut To The Metal Frame/Track Underneath. "Drag Cable - Bracing Mount To Ground V01" Attaches Directly...

Holds a 10x15 drag chain securely to the laser head carriage, keeping air assist hose and any laser pointer wires tightly contained within. I purchased a 10x15 drag chain from Amazon (Black Plastic Drag Chain Cable Carrier 10 x 15mm for CNC Router...

I also turned the servo 90degrees to minimise the height of the cutter in the enclosure and also make the cable run into the drag chain easier. Used drag chain purchased from Amazon. My Y axis chain is fastened to the base of my enclosure so didn't...

Main reason for it are the shark like fins (aka winglets): They reduce drag and turbulence, at least for an airplane... The unique shape of an airplane wing also causes a pressure differential for uplift No clue what all of this means for the fan,...

designed to fit on custom 1/10 scale RC drag racing chassis' probably to narrow for a Traxxas slash or drag slash although may work, it is about 8.9 inches wide (about the same width as an axial SCX10ii) although you could scale it up or down to fit...

I used this $16 drag chain: https://www.walmart.com/ip/Drag-Chain-Cable-Carrier-Open-Type-with-End-Connectors-R28-15X15mm-1-Meter-Plastic-for-Electrical-CNC-Router-Machine/947227151 UPDATE: I found that my original bracket drooped after about a...

This is a Remix of Boothy's Manta MK2 duct system for the Ender 3.I updated some parts to fit better with my setup, as I have a drag chain on my hotend, and wanted to add a connector for the chain.Summary of changes:- Rear_Mount_Plate - Replaced...

For anyone building a drag car and running a small block, a set of long tube headers is a must. This file set represents a wider set of long tube headers than the Hooker setup also available. These have a different bend pattern, attachment angle,...

I used the following drag knife from V1 Engineering: https://shop.v1engineering.com/products/drag-knife-vinyl-cutter I also used (2) left over 3mm nuts and 12mm long screws from the CNC build. I printed the parts with the parting line face down,...

Apart from the attached stl files for 3D printing, you will need several parts to complete the build: a 1mm x 18mm x 40mm compression spring (you can find an example on eBay), two 6mm x 70mm linear rods (available on Aliexpress), and two LM6UU 6mm x...

Here is the rewritten text: Summary I recently created a simple mount for my Vulcanus V1 (2016) cable drag chain and thought others might find it useful. The part attached to the x-carriage (specifically the 2016 model) is secured with acetone, while...

These brackets use standard hardware from the original drag chain and are compatible with right-hand side mounted control boxes. A key feature of these new brackets is the addition of a box on the X-plate to organize long cables and connectors, which...

... it was all I had available. I used a 2" long #10-32 screw and nut to join the two pieces together. Normally, I would print holes for attaching the drag chain, but since there are various styles out there, it's simpler to just drill what you need.

Designed from scratch is a Gear Vendors Overdrive unit as used on many high power drag & drive event cars, high in detail, ideal for scale modeling (currently in 1/24 and 1/25 scale). Perfect for those drag racing builds! File is for the overdrive...

... use for the cable clip (cable clip can be used in combination with the mount). I inserted 3 M3 bolts in the frame mount and pushed them in carefully with a soldering iron so that they they stay firmly in place when you bolt in the drag chain.

The mount is designed for a 20x10mm drag chain, I just ordered this one: http://www.aliexpress.com/snapshot/7852889247.html?spm=2114.13010608.0.53.AkDCg8&orderId=76585111359057 I also uploaded the .stp files, so you can edit the model, if you are...