cool 3d prints

compatibility note: for my testing did it work for EGO’s and GEO’s the only thing to keep in mind is both those 2 have a slightly different hight so you do need to print 2 separate barrel mounts points in case you have both type of markers and like...

blue lines or infill) should be ignored. Post-Printing Assembly Guide Tools needed:* ca 10 wooden toothpicks, 2mm diameter white glue. The one that dries in 5 minutes works best for me.</li> <li>adhesive tape to keep pieces in place, while the...

Then print the 2 models and install them on the printer. For the sensor set it in retract mode and touch the nozzle and the bed. Then place the 2 mm (approx.) allen wrench supplied with the printer between the tip of the sensor and the bed and screw...

Print Settings Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and "Twin Turbo" letters...

... an STL file. The included STL was created while experimenting with TinkerCAD. It's still very much a work in progress, so suggestions and tips are welcome! Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: Doesn't Matter Supports: No

I wanted to print this awesome design by HexiBase on my Ender 3 but the two halves were too big to fit on the build plate so I split each one into two smaller sections. The two sections are joined together via a tongue and groove arrangement, making...

Once the bed has been measured, dropping the nozzle to print height will bring the nail back in range of the magnet and retract it to the stowed position. The M5 iron grub screw attracts the magnet back to center and also helps extend and...

Because of the height of the box, the width of non-snug sleeves, and the text size required to come out visible without a .25mm nozzle (and by Thor, I would not want to print all these separators with that!) it became necessary to make the dividers...

since printing orientations seemed to have a effect on this as well. when tolerances were getting to tight. and making these small lines is easy to do and make it so that you can remove some unwanted play in the parts in case you have some issues...

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

This is to allow for easy switching of 6V battery to USB power and vice versa, without any alteration on the wiring side.Caution: Make sure your LEDs polarity is correct before you solder them in place (refer to the manufacturer design drawing for...

Megacity Desert Habitat building for tabletop, expanded by rectangular build option.It contains:WallsRoof tiles with the capssome special sized doorssome basic bits for decorationYou may need to mirror the corner pieces in your slicer to get all...

If your looking for the original look the v1.0 release at my Github repository: https://github.com/kellyegan/Arduino-Mounting-OpenSCAD-Library The library uses tbuser's pin library for the pin mounts: http://www.thingiverse.com/thing:10541 There are...

Plus cardboard is an amazing garden soil nourishing element. PrintingPrint all the parts with a 0.4mm nozzle (or using the preconfigured files for PLA)  0.6mm for PLA-CF:Matrix : 0.1mm layer height for the bottom grid, then 0.2mm layer height, 20%...

Always turn it off after use and keep an eye on the battery charge.One battery charge should yield 6-12h of usage (depending on resistors and IR LEDs)If you want to use your Wiimotes with the Dolphin emulator on PC, you still need to connect them via...

... Uno. You may also write your own software. I'll also consider requests for a free copy. Send me your request. Print Settings Printer: HyperCube Rafts: No Supports: No Resolution: 0.1mm Infill: 80 Filament: HatchBox PLA Grey Category: Puzzles

On my version, I suggest that you start with 4 seeds in each of the 12 pits (print 4 copies of the 12 seed model and then separate them using nail clippers or small scissors). Increase the number of seeds in each pit progressively to increase the...

Tools ==== * Soldering Iron * Allen Wrench (M3) * Super Glue * hacksaw or carpet knife Assembly ======== * Print the top, bottom, switch bracket and optional hemera bracket * Solder the two pin header to the back of the Duet3d PCB board * Fasten the...

I have no idea if it will work with the wired version.\r\n\r\nParts needed aside from printed objects:\r\n\r\n- 4mm diameter chrome steel ball bearings (available in a package of 100 from VXB.com; you'll need no more than half that)\r\n- 623ZZ...

I printed it with ABS plastic, but PLA or other materials should work fine as well. To ensure it is strong and not prone to breaking easily on my first prototype, I used 50% infill (and four-layer walls) and might use less if I build another one. I...

Case for Atari 1050 / XF551 floppy power supply unit. Krabička pro napájecí zdroj disketové jednotky Atari 1050 / XF551. Print instructionsenglish text bellow ==== CZ ============ Napájecí zdroj pro floppy Atari 1050 / XF551 Jde o návrh napájecího...

**Gravitrax Ball wheel V1.5** - Difference in height 80mm - no support necessary - 2 pressure parts: wheel, pillar - Printing time approx. 5 hours - Select the STL file according to the length of the gearbox, 9.0mm or 12.5mm. - I recommend the...

Program it and what pc software to use to control it. Post-Printing Part List 1x Arduino Uno https://goo.gl/Ha2f1n or Nano https://goo.gl/YUGV6z 5x 9g servos https://goo.gl/J1YWQp 1x 5vdc 2A power supply https://goo.gl/56VuYa Jumper wires...

(Q-tips) Lubricate the sides of the piston with Shimano mineral oil (the same stuff that goes in the brakes) Push the piston back into the caliper. Repeat with the other piston. Park tool has this video available which explains the process without...

Requires 18mm or ¾" holes in the lid and tub for mounting - use a spade bit for a cleaner cut as these containers are quite brittle.A full unit requires 1x Post (Lower), 1x Post (Upper), 2x Sleeves, 2x Through bolts, 2x Bearing Cups, 3x Arm (Hole),...

You can choose to print these as they are, or you can watch our Blender tutorial for the method to easily seperating shells in STL files; Click Here 10 x Space Western heads that feature various stetson hats and bowler hats. All the hats are...

In a few million of years Eros could change its orbit to a lower Earth crossing one, becoming a member of the Apollo or Aten group. Depending on how close it became to the Earth, it could be a Potentially Hazardous object (PHO), an object capable of...

The main point is that the duel disk can now be printed from a single spool, depending on your settings. Then I added some extra features for quality of life. Features: - All slots (monster, spell/trap, graveyard, extra deck) support cards in...

Mount the printed heatblock with the front and back parts of the mold, fix the whole with 2 screws. Make sure it's tight enough. (pictures 7 and 8) 2. Put the freshly assembled block over the bottom part of the mold (picture 9). Make sure the holes...

Also (constructive) criticism or exchange of experiences is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)......