controller headset stand 3d models

Update 02.08.2021: New boat stand by Landon_L was added to the Mods_for_M-Jet_Sprint folder. Thanks for sharing! Update 10.08.2021: New bilge pump mod by Landon_L was added to the Mods_for_M-Jet_Sprint folder. Thanks! Update 14.9.2021: New single...

From a tiny necklace to massive totems standing at the entrance of the building, cutlery, dinner wear and everything in between could be used as a lucky totem. In addition to varying sizes of the tikis, they could also be made in varying materials...

Just stand in front of the mirror at home, place the beard template on the face at the desired location, and then shave at the edges to get your own beard. It is definitely best to use these templates as they can help avoid unnecessary shaving...

N Scale Train Trestle Display I put together these trestles to use as display stands for N gauge engines. One is 10.5 and the other is 5 inches long, but one could easily be made to any length. It is loosely based on a Great Northern Railway Standard...

From a tiny necklace to massive totems standing at the entrance of the building, cutlery, dinner wear and everything in between could be used as a lucky totem. In addition to varying sizes of the tikis, they could also be made in varying materials...

You may want to use the Cura support blocker to remove supports from the pockets for the M3 screws (6th and 7th pics), they should not need supports and getting those small pockets cleaned of supports can be difficult. 0.2mm resolution support brim...

Now including a nice little display stand and a magnet backer.v23.02: Added square divet to support magnets/Velcro in the rear. Meshes have been merged together for optimization.v23.01: Complete ground-up rebuilding of the model for accuracy. Higher...

*Barrel: print standing on the breech, like a smokestack. *<strong>Axle</strong> (2): print with axle tip pointing upward. *<strong>Wheels</strong> (2): print flat. *<strong>Wheel Caps</strong> (2): print with opening pointing upward. *<strong>Spring...

(Don't rely on a wall to be thermally uniform, as there may be conduits or pipes inside.) Run the following command and wait about 5 minutes for it to finish: ~/ctrlr thc This stands for Thermal Calibrate. It takes one thousand consecutive thermal...

The concept was originally inspired from the infamous $100 "Isoacoustic" decoupling stands I had used on an old audiophile system awhile back. What sets this design aside from other common open-baffle setups is that it uses fishing wire to mount...

The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C...

Since this will go in a car, do not use PLA - it won't stand the summer heat. I printed mine in PETG (Atomic Bright White), since it's rigid enough and temperature-tolerant. I do not know what other plastics will work here. Incidentally, the original...

The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C...

The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C...

This has been built in hopes to with stand that. This is 510+/-g at the lowest (LW-PLA-HT prototype; 3s 2200mah) on up pending the filament and battery size you use. Average time to print is dependent on your printer settings. I am able to get it...

From a tiny necklace to massive totems standing at the entrance of the building, cutlery, dinner wear and everything in between could be used as a lucky totem. In addition to varying sizes of the tikis, they could also be made in varying materials...

It currently stands as a prototype, a proof of concept that 3D printing is a viable option for manufacturing PCBs. On the other hand, for those who are interested to print and test the device, see the printer’s note and the components list, and to...

From a tiny necklace to massive totems standing at the entrance of the building, cutlery, dinner wear and everything in between could be used as a lucky totem. In addition to varying sizes of the tikis, they could also be made in varying materials...

The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division...

The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The Chiron stock is probably not worth your time, but it's my sunk cost fallacy fixer upper.The modified Chiron now has:Completely new wiring ditching their annoying proprietary-esque cablingAn SKR2Sensorless homingA HemeraPlated Copper Volcano Hot...

For small/thin parts you need to decrease the Speed by 25% - 50%.Print Speed: 50 mm/s    Infill Speed: 50 mm/s    Wall Speed: 25 mm/s          Outer Wall Speed:25 mm/s          Inner Wall Speed: 50 mm/sTop/Bottom Speed: 25mm/sSupport Speed: 25 mm/s  ...

For small/thin parts you need to decrease the Speed by 25% - 50%.Print Speed: 50 mm/s    Infill Speed: 50 mm/s    Wall Speed: 25 mm/s          Outer Wall Speed:25 mm/s          Inner Wall Speed: 50 mm/sTop/Bottom Speed: 25mm/sSupport Speed: 25 mm/s  ...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

I plan to try boosting that side with a higher-amp case fan tapped straight into my power supply once I work out the speed control. Durability: This design is pretty much brand-new, but I've been running it for about 20 hours of printing now and so...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

For small/thin parts you need to decrease the Speed by 25% - 50%.Print Speed: 50 mm/s    Infill Speed: 50 mm/s    Wall Speed: 25 mm/s          Outer Wall Speed:25 mm/s          Inner Wall Speed: 50 mm/sTop/Bottom Speed: 25mm/sSupport Speed: 25 mm/s  ...

&nbsp;However, I haven't tested this, and you would need to devise your own motor mount and control solution.Printing tips:READ THE STL DESCRIPTIONS!!!Slice the impeller with “union overlapping volumes" because I couldn't be bothered to solid all...